Engineering topics

Mckillip, Robert M., Jr.

Publications and source records attributed to Mckillip, Robert M., Jr..

6 records

NASA NTRS1992

Research on measurement and control of helicopter rotor response using blade-mounted accelerometers 1991-92

Preliminary wind tunnel tests of the hill-size Model 412/IBC rotor at the Ames Research Center, NASA, are described. Blade flapping motion was excited by swash plate oscillation, and the flapping response was measured using blade-mounted accelerometers and compared with flapping motion inferred form blade strain measurements. The recorded open-loop accelerometer signals were used as input to the flapping-IBC system in the laboratory. The resulting controller cyclic pitch outputs are compared with the original cyclic pitch excitation inputs, and the potential effectiveness of the controller in suppressing the original excitation is evaluated. Control of blade flapping excites blade lagging, and vice versa; the paper describes a theoretical investigation of these coupling effects.

Ham, Norman D.↗

NASA NTRS1991

Research on measurement and control of helicopter rotor response using blade-mounted accelerometers 1990-91

Wind tunnel testing of the full-size Model 412/IBC rotor performed at the NASA Ames Research Center is described. The use of blade-mounted accelerometers is found to be feasible for estimating or measuring blade flapping, lagging, and bending accelerations, rates, and displacements. Application of the imaginary swash plate concept to IBC systems leads to useful filtering of the blade accelerometer signals while permitting the control of a four-bladed rotor using measurements from any three blades. Rotor state measurements in the rotating system can be transformed to the corresponding nonrotating rotor states using the IBC algorithm with its associated filtering properties.

Ham, Norman D.↗

NASA NTRS1991

An analytically linearized helicopter model with improved modeling accuracy

An analytically linearized model for helicopter flight response including rotor blade dynamics and dynamic inflow, that was recently developed, was studied with the objective of increasing the understanding, the ease of use, and the accuracy of the model. The mathematical model is described along with a description of the UH-60A Black Hawk helicopter and flight test used to validate the model. To aid in utilization of the model for sensitivity analysis, a new, faster, and more efficient implementation of the model was developed. It is shown that several errors in the mathematical modeling of the system caused a reduction in accuracy. These errors in rotor force resolution, trim force and moment calculation, and rotor inertia terms were corrected along with improvements to the programming style and documentation. Use of a trim input file to drive the model is examined. Trim file errors in blade twist, control input phase angle, coning and lag angles, main and tail rotor pitch, and uniform induced velocity, were corrected. Finally, through direct comparison of the original and corrected model responses to flight test data, the effect of the corrections on overall model output is shown.

Jensen, Patrick T.↗

NASA NTRS1989

Helicopter flight control system design and evaluation for NOE operations using controller inversion techniques

A flight control system design technique is described that allows rapid evaluation of candidate control laws using computer simulated trajectories. The two-step technique first computes the optimum trajectory for the basic aircraft, and then reconstructs the pilot's control displacements necessary to fly this trajectory, given a particular control system architecture. Since the flight control system itself does not add to the acceleration potential of the helicopter, one may evaluate several proposed control laws in terms of the resulting stick inputs for the same maneuver. The method is illustrated through application to implicit and explicit model-following control laws designed for a battlefield helicopter with and without an auxiliary propulsor. It is shown that the technique is a valuable aid for selection of promising control laws for further simulator studies and flight investigations.

Mckillip, Robert M., Jr.↗

NASA NTRS1988

Active control rotor model testing at Princeton's Rotorcraft Dynamics Laboratory

A description of the model helicopter rotor tests currently in progress at Princeton's Rotorcraft Dynamics Laboratory is presented. The tests are designed to provide data for rotor dynamic modeling for use with active control system design. The model rotor to be used incoporates the capability for Individual Blade Control (IBC) or Higher Harmonic Control through the use of a standard swashplate on a three bladed hub. Sample results from the first series of tests are presented, along with the methodology used for state and parameter identification. Finally, pending experiments and possible research directions using this model and test facility are outlined.

Mckillip, Robert M., Jr.↗

NASA NTRS1986

Kinematic observers for active control of helicopter rotor vibration

A simple scheme for estimating the state variables of a helicopter rotor is presented. The method incorporates the use of blade-mounted accelerometers and/or position transducers to reconstruct modal displacements and velocities. The design of the observer structure and feedback gains is simplified by the fact that the method requires only knowledge of basic kinematic relationships between the various modal quantities. The observer structure described is particularly well-suited to control problems where the use of a traditional Kalman Filter approach would be too complex or costly. The technique can be viewed as decreasing the requirements on observer complexity while increasing the need for an enhanced sensor complement.

Mckillip, Robert M., Jr.↗