Search NASA⌕ Search

Engineering topics

Mcmillin, S. Naomi

Publications and source records attributed to Mcmillin, S. Naomi.

6 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Effect of planform and body on supersonic aerodynamics of multibody configurations

An experimental and theoretical investigation of the effect of the wing planform and bodies on the supersonic aerodynamics of a low-fineness-ratio, multibody configuration has been conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.80, 2.00, and 2.16. Force and moment data, flow-visualization data, and surface-pressure data were obtained on eight low-fineness-ratio, twin-body configurations. These configurations varied in inboard wing planform shape, outboard wing planform shape, outboard wing planform size, and presence of the bodies. The force and moment data showed that increasing the ratio of outboard wing area to total wing area or increasing the leading-edge sweep of the inboard wing influenced the aerodynamic characteristics. The flow-visualization data showed a complex flow-field system of shocks, shock-induced separation, and body vortex systems occurring between the side bodies. This flow field was substantially affected by the inboard wing planform shape but minimally affected by the outboard wing planform shape. The flow-visualization and surface-pressure data showed that flow over the outboard wing developed as expected with changes in angle of attack and Mach number and was affected by the leading-edge sweep of the inboard wing and the presence of the bodies. Evaluation of the linear-theory prediction methods revealed their general inability to consistently predict the characteristics of these multibody configurations.

Mcmillin, S. Naomi↗
NASA NTRS1990

Navier-Stokes and Euler solutions for lee-side flows over supersonic delta wings. A correlation with experiment

An Euler flow solver and a thin layer Navier-Stokes flow solver were used to numerically simulate the supersonic leeside flow fields over delta wings which were observed experimentally. Three delta wings with 75, 67.5, and 60 deg leading edge sweeps were computed over an angle-of-attack range of 4 to 20 deg at a Mach number 2.8. The Euler code and Navier-Stokes code predict equally well the primary flow structure where the flow is expected to be separated or attached at the leading edge based on the Stanbrook-Squire boundary. The Navier-Stokes code is capable of predicting both the primary and the secondary flow features for the parameter range investigated. For those flow conditions where the Euler code did not predict the correct type of primary flow structure, the Navier-Stokes code illustrated that the flow structure is sensitive to boundary layer model. In general, the laminar Navier-Stokes solutions agreed better with the experimental data, especially for the lower sweep delta wings. The computational results and a detailed re-examination of the experimental data resulted in a refinement of the flow classifications. This refinement in the flow classification results in the separation bubble with the shock flow type as the intermediate flow pattern between separated and attached flows.

Mcmillin, S. Naomi↗
NASA NTRS1990

A computational study of incipient leading-edge separation on a 65-deg delta wing at M = 1.60

A computational study on a 65-deg delta wing at a freestream Mach number of 1.60 has been conducted by obtaining conical Reynolds-averaged Navier-Stokes solutions on a parametric series of geometries which varied in leading-edge radius and/or circular-arc camber. The computational results showed that increasing leading-edge radius or camber can delay the onset of leading-edge separation on the leeside of a delta wing at a specific angle of attack. Reynolds number was varied from 1 x 10 to the 6th to 5 x 10 to the 6th for a turbulent boundary-layer and was shown to have a minor effect on the effectiveness of leading-edge radius and/or camber in delaying the onset of leading-edge separation. Both laminar and turbulent boundary-layer models were investigated at a Reynolds number of 1 x 10 to the 6th, and the predicted flow pattern was found to change from attached flow for the turbulent boundary-layer model to separated flow for the laminar boundary-layer model. Based upon these results, three wind-tunnel models have been designed to be tested in the Langley Unitary Plan Wind Tunnel.

Mcmillin, S. Naomi↗
NASA NTRS1989

The use of a Navier-Stokes code in the wing design process

The feasibility was determined of incorporating the Navier-Stokes computational code, CFL3D, into the supersonic wing design process. The approach taken is of two steps. The first step was to calibrate CFL3D against existing experimental data sets obtained on thin sharp edged delta wings. The experimental data identified six flow types which are dependent on the similarity parameters of Mach number and angle of attack normal to the leading edge. The calibration showed CFL3D capable of simulating these various separated and attached flow conditions. The second step was to use CFL3D to study the initial formation of leading edge separation over delta wings at supersonic speeds. This consisted of examining solutions obtained on a 65 deg delta wing at Mach number of 1.6 with varying cross sectional shapes. Reynolds number was held constant at 1000000 and the Baldwin-Lomax turbulence model was used. The study showed that through the use of leading edge radius and/or camber, the onset of leading edge separation can be delayed to a higher angle of attack than observed on a flat sharp edged wing. Based on the geometries studied, three wind tunnel models are being designed to verify these results.

Mcmillin, S. Naomi↗
NASA NTRS1988

Experimental and theoretical study of the effects of wing geometry on a supersonic multibody configuration

An experimental and theoretical investigation of planform effects on a low-fineness ratio multibody configuration was conducted in NASA-Langley Research Center's Unitary Plan Wind Tunnel at Mach number of 1.6, 1.8, 2.0 and 2.16. Experimental and theoretical values of lift, drag, and pitching moment as well as surface pressures were obtained on several configurations which varied in both outboard-wing panel and inboard-wing panel planforms. The three outboard-wing panels were a 65 -deg delta and two trapezoidal wing planforms. An unswept and a 60-deg swept inboard-wing panels were also tested. The purpose of the study was to determine the effect of wing planform on the supersonic aerodynamics. The large trapezoidal wing provided increased performance over the small trapezoidal wing primarily due to a reduction in the zero-lift drag coefficient. The swept inboard-wing panel planforms provided a slightly higher L/D than the unswept inboard-wing panel due to a minimal improvement in zero-lift drag. Linear-theory aerodynamic codes were used to analyze the effect of planform on the supersonic aerodynamics and were found to generally produce adequate results.

Bauer, Steven X. S.↗