Engineering topics

Meador, Mary Ann B.

Publications and source records attributed to Meador, Mary Ann B..

67 records · Page 4

NASA NTRS1998

Carbon-13 Labeling Used to Probe Cure and Degradation Reactions of High- Temperature Polymers

High-temperature, crosslinked polyimides are typically insoluble, intractible materials. Consequently, in these systems it has been difficult to follow high-temperature curing or long-term degradation reactions on a molecular level. Selective labeling of the polymers with carbon-13, coupled with solid nuclear magnetic resonance spectrometry (NMR), enables these reactions to be followed. We successfully employed this technique to provide insight into both curing and degradation reactions of PMR-15, a polymer matrix resin used extensively in aircraft engine applications.

Meador, Mary Ann B.↗

NASA NTRS1997

Electron Paramagnetic Resonance Imaging of the Spatial Distribution of Free Radicals in PMR-15 Polyimide Resins

Prior studies have shown that free radicals generated by heating polyimides above 300 C are stable at room temperature and are involved in thermo-oxidative degradation in the presence of oxygen gas. Electron Paramagnetic Resonance Imaging (EPRI) is a technique to determine the spatial distribution of free radicals. X-band (9.5 GHz) EPR images of PMR-15 polyimide were obtained with a spatial resolution of about 0.18 mm along a 2 mm dimension of the sample. In a polyimide sample that was not thermocycled, the radical distribution was uniform along the 2 mm dimension of the sample. For a polyimide sample that was exposed to thermocycling in air for 300 one-hour cycles at 335 C, one-dimensional EPRI showed a higher concentration of free radicals in the surface layers than in the bulk sample. A spectral-spatial two-dimensional image showed that the EPR lineshape of the surface layer remained the same as that of the bulk. These EPRI results suggest that the thermo-oxidative degradation of PMR-15 resin involves free radicals present in the oxygen-rich surface layer.

Ahn, Myong K.↗

NASA NTRS1997

Elucidation of the Cross-Link Structure of Nadic-End-Capped Polyimides Using NMR of C-13-Labeled Polymers

Solid NMR of C-13 isotope-labeled samples of PMR-15 was used to follow the cross-linking reaction of the nadic end cap. Some samples were labeled on one of the carbon atoms of the nadic end cap, and others on the methylene carbon atom of the methylenedianiline portion of the polymer. NMR spectra were run on these samples both before and after cross-linking. In this way, direct evidence of the major products of cross-linking under normal cure conditions is provided. The majority (approximately 85%) of the cross-linking derives from olefin polymerization through the double bond of the end cap. Approximately 15% of the products could come from a pathway involving a retro-Diels-Alder reaction. However, all of the products could be explained by a biradical intermediate without a retro-Diels-Alder reaction. Evidence is also presented that the methylene moiety in the methylenedianiline part of the polymer chain also participates in the cross-linking, albeit to a small extent, by a radical transfer reaction. Different cure conditions (higher temperatures, longer times) could change the relative distribution of the products.

Meador, Mary Ann B.↗

NASA NTRS1997

Electron Paramagnetic Resonance Imaging of the Spatial Distribution of Free Radicals in PMR-15 Polyimide Resins

Prior studies have shown that free radicals generated by heating polyimides above 300 C are stable at room temperature and are involved in thermo-oxidative degradation in the presence of oxygen gas. Electron paramagnetic resonance imaging (EPRI) is a technique to determine the spatial distribution of free radicals. X-band (9.5 GHz) EPR images of PMR-15 polyimide were obtained with a spatial resolution of approximately 0.18 mm along a 2-mm dimension of the sample. In a polyimide sample that was not thermocycled, the radical distribution was uniform along the 2-mm dimension of the sample. For a polyimide sample that was exposed to thermocycling in air for 300 1-h cycles at 335 C, one-dimensional EPRI showed a higher concentration of free radicals in the surface layers than in the bulk sample. A spectral-spatial two-dimensional image showed that the EPR lineshape of the surface layer remained the same as that of the bulk. These EPRI results suggest that the thermo-oxidative degradation of PMR-15 resin involves free radicals present in the oxygen-rich surface layer.

Ahn, Myong K.↗

NASA NTRS1997

Oxidative Degradation of Nadic-End-Capped Polyimides: Evidence for Reactions Occurring at High Temperatures - 2

The oxidative degradation of PMR (for polymerization of monomeric reactants) polyimides at elevated temperatures was followed by cross-polarized magic angle spinning (Cp-MAS) NMR. C-13 labeling of selected sites in the polymers allowed for direct observation of the transformations arising from oxidation processes. As opposed to model compound studies, the reactions were followed directly in the polymer. The labeling experiments confirm the previously reported oxidation of the methylene carbon to ketone in the methylenedianiline portion of the polymer chain. They also show the formation of two other oxidized species, acid and ester, from this same carbon. In addition, the technique provides the first evidence of the kind of degradation reactions that are occurring in the nadic end caps. Several PMR formulations containing moieties determined to be present after oxidation, as suggested by the labeling study, were synthesized. Weight loss, FTIR, and natural abundance NMR of these derivatives were followed during aging. In this way, weight loss could be related to the observed transformations.

Meador, Mary Ann B.↗

NASA NTRS1995

Composite Of Bisfuran/Bismaleimide With Graphite Fibers

Composite-material specimens made of graphite fibers and matrix composed of experimental copolymer of bismaleimide and bisfuran. Found to have mechanical and thermal properties comparable or superior to those of similar composite-material specimens. Candidates for use as lightweight structural components to replace metal components in high-temperature aircraft applications. Bismaleimides used widely for other purposes because of low cost and ease in fabrication. Mechanical properties equal or exceed those of composite made with commercial formulation.

Meador, Mary Ann B.↗

NASA NTRS1991

Electrically conducting polymers for aerospace applications

Current research on electrically conducting polymers from 1974 to the present is reviewed focusing on the development of materials for aeronautic and space applications. Problems discussed include extended pi-systems, pyrolytic polymers, charge-transfer systems, conductive matrix resins for composite materials, and prospects for the use of conducting polymers in space photovoltaics.

Meador, Mary Ann B.↗

NASA NTRS1990

A review of properties and potential aerospace applications of electrically conducting polymers

An overview of current research in conducting polymers is presented. Emphasis is placed on development of materials useful for aeronautic and space applications. Research on organic conducting polymers began in the early 1970s with the discovery of polyacetylene. Since then, many polymers which share structural characteristics with polyacetylene have been prepared which conduct electricity, especially when they are doped with suitable agents. Problems with environmental instability, difficult processing, poor mechanical properties and high cost have slowed the development of conducting polymers. However, practical use of these materials is imminent, based on recent refinements in understanding how polymers conduct, more systematic approaches to the development of new materials, and significant improvements in both the processing and properties.

Meador, Mary Ann B.↗

NASA NTRS1990

Photochemical approaches to ordered polymers

The photocyclization of o-benzyloxyphenyl ketone chromophores provides an efficient, high yield route to the synthesis of 2,3-diphenylbenzofurans. The synthesis and solution of photochemistry of a series of polymers containing this chromophore is described. The photocuring of these polymers is a potential new approach to the synthesis of highly conjugated polymers based upon a p-phenylene bisbenzofuran repeat unit.

Meador, Michael A.↗

NASA NTRS1988

Addition polymers from 1,4,5,8-tetrahydro-1,4;5,8-diepoxyanthracene and Bis-dienes. 2: Evidence for thermal dehydration occurring in the cure process

Diels-Alder cycloaddition copolymers from 1,4,5,8-tetrahydro-1,4;5,8-diepoxyanthracene and anthracene end-capped polyimide oligomers appear, by thermogravimetric analysis (TGA), to undergo dehydration at elevated temperatures. This would produce thermally stable pentiptycene units along the polymer backbone, and render the polymers incapable of unzipping through a retro-Diels-Alder pathway. High resolution solid 13C nuclear magnetic resonance (NMR) of one formulation of the polymer system before and after heating at elevated temperatures, shows this to indeed be the case. NMR spectra of solid samples of the polymer before and after heating correlated well with those of the parent pentiptycene model compound before and after acid-catalyzed dehydration. Isothermal gravimetric analyses and viscosities of the polymer before and after heat treatment support dehydration as a mechanism for the cure reaction.

Meador, Mary Ann B.↗

NASA NTRS1988

Processable, high temperature polymers from 1,4,5,8-tetrahydro-1,4;5,8-diepoxyanthracene and bis-dienes

1,4,5,8-tetrahydro-1,4;5,8-diepoxyanthracene reacts with various anthracene end-capped polyimide oligomers to form Diels-Alder cycloaddition copolymers. The polymers are soluble in common organic solvents, and have molecular weights of approximately 21,000 to 32,000. These resins exhibit lower weight loss in air than in nitrogen. This is suggested to be due to dehydration (loss of water ranges from 2 to 5 percent) at temperatures of 390 to 400 C to give thermooxidatively stable pentiptycene units along the polymer backbone. Because of their high softening points and good thermooxidative stability, the polymers have potential as processable, matrix resins for high temperature composite applications.

Meador, Mary Ann B.↗

NASA NTRS1987

Addition polymers from 1,4,5,8-tetrahydro-1,4;5,8-diepoxyanthracene and Bis-dienes: Processable resins for high temperature application

1,4,5,8-Tetrahydro-1,4;5,8-diepoxyanthracene reacts with various anthracene endcapped polyimide oligomers to form Diels-Alder cycloaddition copolymers. The polymers are soluble in common organic solvents, and have molecular weights of approximately 21,000 to 32,000. Interestingly, these resins appear to be more stable in air then in nitrogen. This is shown to be due to a unique dehydration (loss of water ranges from 2 to 5 percent) at temperatures of 390 to 400 C to give thermo-oxidatively stable pentiptycene units along the polymer backbone. Because of their high softening points and good thermo-oxidative stability, the polymers have potential as processible, matrix resins for high temperature composite applications.

Meador, Mary Ann B.↗

NASA NTRS1987

A mechanistic study of polyimide formation from diester-diacids

Previous work has noted the presence of anhydride during the imidization step of polyimide polymer processing from diester-diacids and diamines. Comparison of the relative rates of reactions among model compounds demonstrates the intermediacy of anhydride in the imidization reaction. IR and NMR observations of mixtures of monomers confirm the production of anhydride as a necessary intermediate in the imidization reaction.

Johnston, James C.↗