Uranium-zirconium hydride nuclear fuel performance in the NaK-cooled MARVEL microreactor
Not Available
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Engineering topics
Medvedev, Pavel G.
Publications and source records attributed to Medvedev, Pavel G..
Reactor fuel pellets with thermally-conductive inserts, and related reactor fuel pellet arrangements
Fuel pellets and fuel pellet arrangements include thermally-conductive inserts within a fuel. The inserts have at least one portion of a thermally-conductive material, such as radially-extending fins. The inserts are configured to dissipate heat during use of the fuel pellets, while minimizing the amount of the total volume of the fuel pellet that is occupied by non-fissile material. The inclusion of heat-dissipating inserts enables the fuel pellets to exhibit improved thermal performance over the lifetime of the fuel, including a relatively low peak temperature and relatively low integrated average temperatures, while the minimal volume of the inserts avoids significantly decreasing the percent of enrichment achievable.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
BISON fuel performance modeling optimization for experiment X447 and X447A using axial swelling and cladding strain measurements
With the recent need to qualify new reactor designs such as the Versatile Test Reactor (VTR), fuel performance calculations need to be performed to determine safety criteria of the proposed designs. In order to validate the fuel performance results obtained by a fuel performance code, BISON, for new reactor designs, legacy fuel from EBR-II and FFTF MFF with Post -Irradiation Examination (PIE) data need to be used as validation cases to benchmark models. Here in this work, BISON has been paired with the Fuels Irradiation & Physics Database (FIPD) and IFR Materials Information System (IMIS) to supply PIE data for comparison with simulations of EBR-II experiments X447/X447A. X447/X447A were assessed by implementing models for Fuel Cladding Chemical Interaction (FCCI) within BISON and optimizing the friction coefficient between the fuel surface and the cladding, the anisotropic swelling factor, and the HT9 first thermal creep scalar (which scales the first term in the HT9 creep equation) to best match the PIE axial fuel swelling height and cladding profilometry for all pins in X447/X447A. The optimal values were found using a generic algorithm developed to select different values for the three parameters until end criteria was met and error couldn’t be reduced further. The BISON-simulated cladding profilometry was evaluated using Standard Error of the Estimate (SEE) to account for the profile shape of the cladding profilometry. Optimal values for the friction coefficient, anisotropic fuel swelling factor, and HT9 first thermal creep scalar were found to best fit the BISON simulation results to the PIE measurements found in IMIS and FIPD. Improvements to current models are suggested to account for the underprediction of fuel swelling at low burnups and the overprediction of fuel swelling at higher burnups observed for the axial fuel swelling height. Although two pins in EBR-II X447/X447A (DP70 and DP75) were known to fail due to FCCI, none of the pins simulated in BISON reached a cumulative damage fraction (CDF) above 0.008 with FCCI correlations coupled in the BISON simulations. The error estimate generated for all pins in X447/X447A using optimal values was 209 µm, which is deemed acceptable.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
An analysis of fluff formation in metallic fuel via data analyzes from EBR-II experiments and BISON fuel code modeling
During the operation of EBR-II, it was found that a highly porous structure (over 40% area fraction) formed at the top of several fuel columns. Previous work has shown that this structure, designated fluff in this paper, contains a significant fraction of fuel elements (e.g., U and Pu) which could potentially impact neutronics. This work aims in analyzing the formation mechanism of this microstructure so its impact can be incorporated into future metallic fuel modeling codes and algorithms. This paper details a preliminary examination into the formation mechanisms of fluff by performing qualitative and statistical analysis of EBR-II experimental data. Additionally, the operating conditions that have the greatest impact on fluff formation were determined based on this data set. Also, BISON fuel code simulations were used to help postulate potential fluff formation mechanisms. From this analysis it was found that the largest contributors to fluff formation were fuel burnup and composition, with fluff formation exhibiting a roughly linear positive correlation with increasing burnup and a negative correlation with increasing Pu content. It was also found that higher pin operating temperatures decreased fluff formation but only for U-10Zr fuels.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Irradiation performance of nonfertile (Pu-MA-Zr) fast reactor metal fuels
This work was part of a program begun in 2001 to develop advanced nuclear fuels, originally as carriers for plutonium and minor actinides (neptunium, curium, and americium) taken from spent commercial light-water reactors (LWR) so that the plutonium and minor actinides could be ‘burned’ or transmuted in an accelerator or a fast nuclear reactor. A central part of these experiment programs has been the development of advanced fast reactor fuels, because a fast reactor was considered the most efficient vehicle to transmute the actinide waste products, and metallic fuels is a central focus of these tests. An experiment design was developed in which a thermal test reactor, the Advanced Test Reactor (ATR), was used to test small fuel pin prototypes, by creating areas in the core shielded by cadmium filters to produce a largely epithermal and fast neutron spectrum environment in which the pins could be irradiated. The results of non-fertile metallic fuel (no uranium) tests are presented here. Pu-Am-Np-Zr fuels were irradiated to fission densities up to 33 × 10 20 fission/cm 3 and Pu-239 depletions of up to 39%. The depletions were created by roughly 2/3 by fission and 1/3 by transmutation neutron capture. Up to five fuel ‘rodlets’ were irradiated in three sealed capsules stacked axially in the core, and the peak cladding temperatures ranged from 300°C to 500°C, depending on axial location as those near the core centerline are operating hotter and to higher fission densities. Several post-irradiation examinations (precision gamma scanning and fission gas release) were similar to other historical metal fuel experiments in fast reactors. However, optical metallography indicated that two of the rodlets had breached. The exact reasons are unclear. Due to the design of this irradiation experiment a rodlet breach could have increased the temperature in others in the same capsule by contaminating the thermal gap helium with heavier and less conductive fission product gases. Finally, some of those rodlets showed high amounts of fuel/cladding chemical interaction (FCCI).
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗