Search NASA⌕ Search

Engineering topics

Meek, Kelly M.

Publications and source records attributed to Meek, Kelly M..

A Sustainable Multi-Dimensional Printable Material

Polymeric materials are usually tailored for specific functionality. A single polymer exhibiting multiple simultaneous functionalities often requires intricate molecular architecture, which is difficult to manufacture at scale because of its complex synthesis routes. In this work, a facile, partly renewable composition—prepared via reactive melt processing—that induces tunable functionalities such as 3D printability, shape recovery, and self-healing while exhibiting satisfactory mechanical properties is reported. The system with a hydrogen-bonded 3D network consists of thermally reversible nano-scale agglomerates of sustainable, rigid phenolic oligomers and crystallizable flexible polymer. Local molecular mobility and temperature-dependent relaxation and recovery of the non-equilibrium networked states enable exploiting these simultaneous functionalities. Transitions involving solidification and structure stabilization at ambient temperature spanning several hours after preheating only at 70 °C directly contrast typical thermoplastic or thermoplastic elastomer behaviors. Results from this study can inform the design of future rheology modifiers and materials for soft robotics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-Throughput Anion Exchange Membrane Characterization at NREL

Anion exchange membrane fuel cells (AEMFCs) are of high interest because they utilize lower cost catalyst and separator materials relative to proton exchange membrane fuel cells (PEMFCs). AEMFCs require anion exchange membranes (AEMs) that have high alkaline chemical stability, high hydroxide ion conductivity, and adequate thermal/mechanical properties. We report NREL has developed protocols to allow for high throughput, parallel characterization of AEM materials. More specifically, NREL has received membranes from more than 10 partners and has tested more than 50 membranes using these approaches. In many cases these ex-situ results can be compared to fuel cell performance and durability. Technical investigations include conductivity, ion exchange capacity, mechanical performance, chemical stability, thermal properties, water uptake, and swelling. Structure-property relationships that affect membrane performance and durability will be discussed, lending insight into optimal backbone and cation strategies to employ in development of AEMs.

30 DIRECT ENERGY CONVERSION↗

Nitrogen-doped carbons derived from poly(ionic liquid)s with various backbones and cations

In this study, poly(ionic liquid)s (PILs) with various backbone/cation pairings (backbones - ethyl methacrylate, styrene; covalently attached cations - butylimidazolium, trimethylammonium, butylpyrrolidinium) were successfully synthesized as carbon precursors. Pyrolysis of PILs produced carbons with sheet-like structures with a metallic luster in contrast to the powder form of carbons produced from polyacrylonitrile. The results also show that cation type has a significant impact on surface area, graphitic content, graphitic nitrogen content, nitrogen retention, carbon yield and surface chemistry of the PIL-derived carbons. The design of nitrogen-doped carbons based on a diverse set of PILs with various cation and polymer backbone chemistries may be an effective strategy to optimize carbon properties for subsequent application in energy storage devices.

36 MATERIALS SCIENCE↗

A path for lignin valorization via additive manufacturing of high-performance sustainable composites with enhanced 3D printability

Here, we report the manufacture of printable, sustainable polymer systems to address global challenges associated with high-volume utilization of lignin, an industrial waste from biomass feedstock. By analyzing a common three-dimensional printing process—fused-deposition modeling—and correlating the printing-process features to properties of materials such as acrylonitrile-butadiene-styrene (ABS) and nylon, we devised a first-of-its-kind, high-performance class of printable renewable composites containing 40 to 60 weight % (wt %) lignin. An ABS analog made by integrating lignin into nitrile-butadiene rubber needs the presence of a styrenic polymer to avoid filament buckling during printing. However, lignin-modified nylon composites containing 40 to 60 wt % sinapyl alcohol–rich, melt-stable lignin exhibit enhanced stiffness and tensile strength at room temperature, while—unexpectedly—demonstrating a reduced viscosity in the melt. Further, incorporation of 4 to 16 wt % discontinuous carbon fibers enhances mechanical stiffness and printing speed, as the thermal conductivity of the carbon fibers facilitates heat transfer and thinning of the melt. We found that the presence of lignin and carbon fibers retards nylon crystallization, leading to low-melting imperfect crystals that allow good printability at lower temperatures without lignin degradation.

36 MATERIALS SCIENCE↗

Responsive lignin for shape memory applications

Here, we analyze thermally unstable lignin linkages that generate reactive sites and promote crosslinking reactions during thermal annealing at 180 °C. This results in significantly enhanced glass transition temperature (Tg). We use these characteristics of lignin to enhance interfacial reactivity of a lignin-based multiphase polymer synthesized by a dynamic shear process. An approximately 18 °C increase in Tg and more than 230% increase in storage modulus (E') are achieved by thermally annealing the 50 wt% hardwood lignin-nitrile rubber composite for 5 h at 180 °C. Tunable chemical and physical crosslinks within lignin and rubber resulted in shape programmability demonstrating excellent strain recovery of the synthesized renewable materials. The substantial improvement of the elastic work density of the lignin-based elastomers allows a broader applicable stress window for stress/strain sensing. The renewable materials also exhibit a better strain recovery after thermal annealing.

36 MATERIALS SCIENCE↗

Reductive Catalytic Fractionation of C-Lignin

Lignin composed solely of caffeyl alcohol units, or C-lignin, was recently discovered in the seed coats of a number of vanilla orchid and cactus species. The caffeyl alcohol monomer polymerizes into a highly uniform benzodioxane backbone, making C-lignin a promising substrate for lignin valorization, where heterogeneity is a key challenge. In this study, we used reductive catalytic fractionation (RCF) on vanilla seeds to investigate the depolymerization of naturally grown C-lignin. To overcome challenges associated with the high extractive content and poor sugar retention in vanilla seeds, the ratio of monomer yield to total lignin yield was used to isolate the depolymerization efficiency of C-lignin from the extraction efficiency of lignin from seeds. This approach allowed us to compare extents of depolymerization across lignin types and biomass feedstocks. C-Lignin RCF generated extents of depolymerization akin to those of hardwoods, despite observing incomplete benzodioxane cleavage due to catalyst deactivation caused by the seed extractives. In addition, depolymerization of C-lignin produced a favorable monomeric product distribution consisting of only propyl and propenyl catechol. These promising results suggest that genetic modification of other plant species to incorporate C-lignin has the potential to yield a single, valuable catechol product via RCF.

09 BIOMASS FUELS↗

A Solvent-Free Synthesis of Lignin-Derived Renewable Carbon with Tunable Porosity for Supercapacitor Electrodes

Synthesis of multiphase materials from lignin, a biorefinery coproduct, offers limited success owing to the inherent difficulty in controlling dispersion of these renewable hyperbranched macromolecules in the product or its intermediates. Effective use of the chemically reactive functionalities in lignin, however, enables tuning morphologies of the materials. Here in this study, we bind lignin oligomers with a rubbery macromolecule followed by thermal crosslinking to form a carbon precursor with phase contrasted morphology at submicron scale. The solvent-free mixing is conducted in a high-shear melt mixer. With this, the carbon precursor is further modified with potassium hydroxide for a single-step carbonization to yield activated carbon with tunable pore structure. A typical precursor with 90 % lignin yields porous carbon with 2120 m 2 g -1 surface area and supercapacitor with 215 F g -1 capacitance. Lastly, the results show a simple route towards manufacturing carbon-based energy-storage materials, eliminating the need for conventional template synthesis.

36 MATERIALS SCIENCE↗

γ-Valerolactone-Extracted Lignin to Porous Carbon Materials

Synthesis of multiphase materials from lignin, a biorefinery coproduct, offers limited success due to the inherent difficulty in controlling dispersion of these renewable hyperbranched macromolecules in the product or its intermediates. Effective use of the chemically reactive functionalities in lignin, however, enables tuning morphologies of the materials. Here, we bind a lignin oligomer with a rubbery macromolecule followed by thermal crosslinking to form a carbon precursor with phase contrasted morphology at submicron scale. The solvent-free mixing is conducted in a high-shear melt-mixer. With this, the carbon precursor is further modified with potassium hydroxide for a single-step carbonization to yield activated carbon with tunable pore structure. A typical precursor with 90% lignin yields porous carbon with 2120 m 2 /g surface area and a supercapacitor with 215 F/g capacitance. The results show a simple route towards manufacturing carbon-based energy-storage materials, eliminating the need for conventional template-synthesis.

36 MATERIALS SCIENCE↗

Polymerized ionic liquids: Effects of counter-anions on ion conduction and polymerization kinetics

A novel imidazolium–containing monomer, 1–[ω–methacryloyloxydecyl]–3–(n–butyl)–imidazolium (1BDIMA), was synthesized and polymerized using free radical and controlled free radical polymerization followed by post–polymerization ion exchange with bromide (Br), tetrafluoroborate (BF 4 ), hexafluorophosphate (PF 6 ), or bis(trifluoromethylsulfonyl)imide (Tf 2 N). The thermal properties and ionic conductivity of the polymers showed a strong dependence on the counter–ions and had glass transition temperatures ( T g ) and ion conductivities at room temperature ranging from 10 °C to –42 °C and 2.09 × 10 –7 S cm –1 to 2.45 × 10 –5 S cm –1 . In particular, PILs with Tf 2 N counter–ions showed excellent ion conductivity of 2.45 × 10 –5 S cm –1 at room temperature without additional ionic liquids (ILs) being added to the system, making them suitable for further study as electro–responsive materials. In addition to the counter–ions, solvent was found to have a significant effect on the reversible addition–fragmentation chain–transfer polymerization (RAFT) for 1BDIMA with different counter–ions. For example, 1BDIMATf2N would not polymerize in acetonitrile (MeCN) at 65 °C and only achieved low monomer conversion (< 5%) at 75 °C. However, 1BDIMA–Tf 2 N proceeded to high conversion in dimethylformamide (DMF) at 65 °C and 1BDIMABr polymerized significantly faster in DMF compared to MeCN. NMR diffusometry was used to investigate the kinetic differences by probing the diffusion coefficients for each monomer and counter–ion in MeCN and DMF. Furthermore, these results indicate that the reaction rates are not diffusion limited, and point to a need for deeper understanding of the role electrostatics plays in the kinetics of free radical polymerizations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An Acrylonitrile–Butadiene–Lignin Renewable Skin with Programmable and Switchable Electrical Conductivity for Stress/Strain-Sensing Applications

We report an approach for programming electrical conductivity of a bio-based leathery skin devised with a layer of 60 nm metallic nanoparticles. Lignin-based renewable shape-memory materials were made, for the first time, to program and restore the materials’ electrical conductivity after repeated deformation up to 100% strain amplitude, at a temperature 60–115 °C above the glass transition temperature (T g ) of the rubbery matrix. We cross-linked lignin macromolecules with an acrylonitrile–butadiene rubbery melt in high quantities ranging from 40 to 60 wt % and processed the resulting thermoplastics into thin films. Chemical and physical networks within the polymeric materials significantly enhanced key characteristics such as mechanical stiffness, strain fixity, and temperature-stimulated recovery of shape. The branched structures of the guaiacylpropane-dominant softwood lignin significantly improve the rubber’s T g and produced a film with stored and recoverable elastic work density that was an order of magnitude greater than those of the neat rubber and of samples made with syringylpropane-rich hardwood lignin. The devices could exhibit switching of conductivity before and after shape recovery.

36 MATERIALS SCIENCE↗