Engineering topics
Mehrabi, Hamed
Publications and source records attributed to Mehrabi, Hamed.
Modular Solar-to-Fuel Electrolysis at Low Cell Potentials Enabled by Glycerol Electrooxidation and a Bipolar Membrane Separator
Solar fuel generation through water electrolysis or electrochemical CO 2 reduction is thermodynamically limited when paired with the oxygen evolution reaction (OER). The glycerol electrooxidation reaction (GEOR) is an alternative anodic reaction with lower anodic electrochemical potential that utilizes a renewable coproduct produced during biodiesel synthesis. We show that GEOR on a Au-Pt-Bi ternary metal electrocatalyst in a model alkaline crude glycerol solution can provide significant cell potential reductions even when paired to reduction reactions in seawater and acidic catholytes via a bipolar membrane (BPM). We showed that the combination of GEOR electrooxidation and a BPM separator lowers the total cell potential by 1 V at an electrolysis current of 10.0 mA cm -2 versus to an anode performing OER when paired with hydrogen evolution and CO 2 reduction cathodes. The observed voltage reduction was steady for periods of up to 80 hours, with minimal glycerol crossover observed through the membrane. Furthermore, these results motivate new, high-performance cell designs for photoelectrochemical solar fuels integrated systems based on glycerol electrooxidation.
Electrochemical Control of the Morphology and Functional Properties of Hierarchically Structured, Dendritic Cu Surfaces
Electrodeposited dendritic copper foams have been extensively studied as an electrocatalyst for CO 2 reduction reaction (CO 2 RR). Many parameters, such as dendrite size, porosity, pore size, and crystal faceting, define the hierarchical properties of these structures and their subsequent bubble evolution and CO 2 RR capabilities. Herein, the effects the electrodeposition conditions (potential, pH) have on the resulting crystallinity, microstructure, and macroporosity of the copper foam are studied. These morphological differences and the corresponding effects on electrocatalytic activity are characterized. It is shown that the composition of the electrodeposition bath can have significant effects on the mechanics of bubble formation and detachment at the surface during hydrogen evolution reaction in acidic solutions. Similarly, the electrodeposition conditions for the synthesis of the foam affect the product selectivity during CO 2 RR electrocatalysis. As a result, foams deposited in alkaline electrodeposition solutions show high faradaic efficiency and specificity toward C 2 H 6 , an uncommon product of CO 2 RR, at modest applied potentials (−0.8 V versus reversible hydrogen electrode.
Characterizing Sustained Solar-to-Hydrogen Electrocatalysis at Low Cell Potentials Enabled by Crude Glycerol Oxidation
Unassisted solar-driven water electrolysis as a sustainable source for H 2 is limited by the high overpotential necessary to drive the oxygen evolution reaction (OER). Crude glycerol is an extremely alkaline byproduct of biodiesel synthesis that can be valorized or refined to produce more desirable chemicals. Glycerol can also be directly oxidized on an anode, replacing water oxidation, to reduce the applied cell potential requirements of electrolytic H 2 production or CO 2 reduction. An advantage of oxidizing glycerol in its crude form is the opportunity to valorize it without initial refinement. We describe an approach to replace the OER half-reaction with the sacrificial crude glycerol electrooxidation on a layered Au–Pt–Bi electrocatalyst on a Ni substrate. Compared to compositions with fewer components, the AuPtBi–Ni electrocatalyst improved the duration of performance and reduced the overall cell potential for glycerol electrooxidation in the extreme alkaline solutions representative of crude glycerol. These enhancements facilitated extended, unassisted hydrogen evolution from crude glycerol electrolysis, even under the power of a single-junction silicon solar cell at less than 1 sun illumination. We characterized the oxidation products of crude glycerol electrolysis and the subsequent products formed spontaneously in the electrolyte in the highly alkaline solution. This analysis helps to both identify the stoichiometric limits of glycerol oxidation at the low cell potentials of interest here and to understand the chemical control imparted by electrocatalysis on the ultimate compounds formed in the crude solution. Furthermore, the results for the AuPtBi electrocatalyst show that incorporating crude glycerol oxidation into integrated electrochemical systems can simultaneously simplify their design and significantly improve solar-to-hydrogen rates.
Controlled exposure of CuO thin films through corrosion-protecting, ALD-deposited TiO 2 overlayers
Ultra-thin film coatings are used to protect semiconductor photoelectrodes from the harsh chemical environments common to photoelectrochemical energy conversion. These layers add contact transfer resistance to the interface that can result in a reduction of photoelectrochemical energy conversion efficiency of the photoelectrode. Here, we describe the concept of a partial protection layer, which allows for direct chemical access to a small fraction of the semiconductor underlayer for further functionalization by an electrocatalyst. The rest of the interface remains protected by a stable, inert protection layer. CuO is used as a model system for this scheme. Atomic layer deposition (ALD)-prepared TiO 2 layers on CuO thin films prepared from electrodeposited Cu 2 O allow for the control of interfacial morphology to intentionally expose the CuO underlayer. The ALD-TiO 2 overlayer shrinks during crystallization, while Cu 2 O in the underlayer expands during oxidation. As a result, the TiO 2 protection layer cracks to expose the oxidized underlying CuO layer, which can be controlled by preceding thermal oxidation. Furthermore, this work demonstrates a potentially promising strategy for the parallel optimization of photoelectrochemical interfaces for chemical stability and high performance.
Probe metal binding mode of imine covalent organic frameworks: cycloiridation for (photo)catalytic hydrogen evolution from formate
This study describes cyclometallation as a new metal binding mode for imine-based COFs. The iridacycle decorated COF could be used for catalytic hydrogen evolution from aqueous formate solution with high stability and high efficacy.