Search NASA⌕ Search

Engineering topics

Melfi, L. T., Jr.

Publications and source records attributed to Melfi, L. T., Jr..

17 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Rocket nozzle lip flow by direct simulation Monte Carlo method

The flow in the immediate vicinity of a rocket nozzle lip has been analyzed, and the results are presented. A rapid change in gas composition is observed in the flow around the lip depending principally on species molecular mass and local flow angle. The divergence of axial and radial temperatures indicating breakdown of translational equilibrium is observed in the results.

Hueser, J. E.↗
NASA NTRS1984

Analysis of large solid propellant rocket engine exhaust plumes using the direct simulation Monte Carlo method

A new solution procedure has been developed to analyze the flowfield properties in the vicinity of the Inertial Upper Stage/Spacecraft during the 1st stage (SRMI) burn. Continuum methods are used to compute the nozzle flow and the exhaust plume flowfield as far as the boundary where the breakdown of translational equilibrium leaves these methods invalid. The Direct Simulation Monte Carlo (DSMC) method is applied everywhere beyond this breakdown boundary. The flowfield distributions of density, velocity, temperature, relative abundance, surface flux density, and pressure are discussed for each species for 2 sets of boundary conditions: vacuum and freestream. The interaction of the exhaust plume and the freestream with the spacecraft and the 2-stream direct interaction are discussed. The results show that the low density, high velocity, counter flowing free-stream substantially modifies the flowfield properties and the flux density incident on the spacecraft. A freestream bow shock is observed in the data, located forward of the high density region of the exhaust plume into which the freestream gas does not penetrate. The total flux density incident on the spacecraft, integrated over the SRM1 burn interval is estimated to be of the order of 10 to the 22nd per sq m (about 1000 atomic layers).

Hueser, J. E.↗
NASA NTRS1981

Direct simulation Monte Carlo technique for modeling of the environment in the vicinity of the Space Shuttle Orbiter

A program for analyzing the flowfield parameters in the neighborhood of the Space Shuttle Orbiter has been developed. The program uses the direct simulation Monte Carlo method, which is a completely probabilistic Monte Carlo technique capable of analyzing 3-dimensional steady or unsteady flow with prescribed internal and external boundary conditions. The freestream flux densities incident on the external flowfield boundaries are calculated from the drifting Maxwellian gas properties of the freestream. The flux entering the flowfield from the internal boundary is calculated from the outgassing flux density distribution over the Shuttle external surface and the prescribed discrete source fluxes. This technique produces a numerical flowfield solution which is the probabilistic equivalent of a complete solution of the time-dependent, 3-dimensional Boltzmann equation. Flowfield results are presented for the following configurations: (1) Shuttle angles of attack of 0 and 90 deg, (2) freestream density 10 to the 9th - 10 to the 11th per cu cm, (3) Shuttle outgassing flux density, and (4) operation of the aft downfiring vernier Reaction Control System (RCS) engine. Results are presented for column density distribution of outgassed and engine species and for the flux density of outgassed and engine species incident on the Shuttle bay and the windshield.

Melfi, L. T., Jr.↗
NASA NTRS1976

Characteristics and potential applications of orbiting ultrahigh vacuum facilities

The characteristics of an orbiting molecular shield ultrahigh vacuum facility are described and some examples of potential applications are discussed. Published results of a kinetic theory analysis are given. Densities within the shield of less than 1000 molecules/cu cm can be obtained allowing high purity materials processing experiments to be performed in orbit under the simultaneous conditions of ultrahigh vacuum and microgravity. Two specific experiments are discussed: the production of ultrapure materials by the electrotransport technique developed at ERDA's Ames Laboratory, Iowa State University, and the vapor deposition and space preparation of silicon solar cells.

Melfi, L. T., Jr.↗
NASA NTRS1976

Molecular shield - An orbiting low-density materials laboratory

Analysis of a molecular shield orbited at 200 km utilizes the kinetic theory of a drifting Maxwellian gas, applied to a hemispherical shell geometry containing internal sources. The molecular shield provides very low gas density conditions for materials experiments at low gravity, while the hemispherical geometry minimizes the internal surface/volume ratio. Deployment of the shield in orbit is described. Contributions to density by shield outgassing, by experiment outgassing, and by interaction with the orbiter are discussed separately. A jettisonable closure plate sealing the hemisphere minimizes any risk of experiment contamination during deployment.

Melfi, L. T., Jr.↗
NASA NTRS1975

An orbiting molecular shield vacuum facility - A materials laboratory in space

Certain classes of materials processing experiments require a combination of near zero gravity and ultrahigh vacuum. This combination of environmental requirements can be obtained within a molecular shield vacuum facility deployed from the Space Shuttle Orbiter. To avoid degradation by Orbiter effluents, it is necessary to deploy the facility from the Orbiter's immediate vicinity to a distance of about 100 meters. This may be achieved with an extendable/retractable boom, so that power and other resources are supplied by the Orbiter. Alternatively, the facility may be deployed as a free-flyer satellite and retrieved on a subsequent Orbiter mission. Preliminary results of boom design and dynamics analyses are presented.

Youngblood, J. W.↗
NASA NTRS1975

Switching regulator emission control circuit for ion sources

An electron emission control circuit of the switching regulator type operating at 100 kHz has been developed which maintains a constant emission current within 0.1% for a cathode power demand variation of approximately 100%. The power output stage has an efficiency of 67%, and the overall efficiency is 45% when driving a thoria-coated iridium cathode having a nominal resistance at operating temperature of 2.5 ohms. Under optimum conditions, the bus power demand is 1.75 W. The circuit is useful in controlling the electron emission current of ion sources in applications which involve a substantial variation of the cathode work function, such as oxygen partial pressure measurements over a large dynamic range.

Clay, F. P., Jr.↗
NASA NTRS1974

A new approach to mass spectrometer measurements of thermospheric density

The gas sampling problem in satellite and high velocity probes was investigated by applying the theory of a drifting Maxwellian gas. A lens system using a free stream ion source was developed and experimentally evaluated over the pressure range of 0.00001 to 0.01 N/m sq (approx. 10 to the minus 7th power to 0.0001 torr). The source has high beam transparency, which minimizes gas-surface collisions within, or near, the ionization volume. It is shown that for high ion energy (60 eV), the extracted ion beam has an on-axis energy spread of less than 4 eV, and that 90 percent of the ions are within 2.5 deg of the beam axis. It is concluded that the molecular beam mass spectrometer concept, developed for gas density measurements in the upper atmosphere, substantially reduces gas-surface scattering and gas-surface reactions in the sample, and preserves the integrity of the gas sample during the analysis process. Studies show that both the Scout and Delta launch vehicles have adequate volume, control, velocity, and data acquisition capability necessary to obtain thermospheric number density in real time.

Melfi, L. T., Jr.↗