Search NASA⌕ Search

Engineering topics

Mellors, Robert J.

Publications and source records attributed to Mellors, Robert J..

At least 19 records

0.340909091

Explore the source record for details and available documents.

Hodgkinson, Kathleen Marian↗

Comparisons Between Array Derived Dynamic Strain Rate (ADDS) and Fiber‐Optic Distributed Acoustic Sensing (DAS) Strain Rate

Abstract Distributed acoustic sensing (DAS) strain rate and particle velocity can be compared through approximate scaling with medium velocity. We instead performed a direct comparison between array derived dynamic strain (ADDS) rate and DAS strain rate for six frequency bands. The PoroTomo project at Brady's Hot Springs, Nevada, deployed a 240‐geophone 3C array co‐located with fiber‐optic DAS system and 8.7 km of buried cable. We selected subsets of the geophone array to create four smaller arrays and computed ADDS. The horizontal components of the ADDS were rotated into the direction of the fiber‐optic cable and then compared with the observed DAS strain rates. From three example regional earthquakes of local magnitudes 2.9, 4.1, and 4.3, the ADDS are found to be coherent with DAS for frequencies ≤1 Hz. For frequencies >1‐Hz, this correlation decays quickly. Small differences between linear and areal dynamic strains at 1‐Hz suggest poor signal‐to‐noise or localized strain that is perturbed by shallow heterogeneities compare to the average strain propagating across the geophone array. The implication is that around 1‐Hz, straight fiber DAS is measuring axial strain along the fiber and can provide good approximations to translational particle motions. However, above 1‐Hz, DAS becomes more sensitive to shallow velocity gradients that can be beneficial for geophysical imaging yet becomes a limitation for traditional seismic analysis methods depending on absolute amplitude and phase from translational particle motions.

58 GEOSCIENCES↗

Atmospheric waves and global seismoacoustic observations of the January 2022 Hunga eruption, Tonga

The 15 January 2022 climactic eruption of Hunga volcano, Tonga, produced an explosion in the atmosphere of a size that has not been documented in the modern geophysical record. The event generated a broad range of atmospheric waves observed globally by various ground-based and spaceborne instrumentation networks. Most prominent was the surface-guided Lamb wave (≲0.01 hertz), which we observed propagating for four (plus three antipodal) passages around Earth over 6 days. As measured by the Lamb wave amplitudes, the climactic Hunga explosion was comparable in size to that of the 1883 Krakatau eruption. The Hunga eruption produced remarkable globally detected infrasound (0.01 to 20 hertz), long-range (~10,000 kilometers) audible sound, and ionospheric perturbations. Seismometers worldwide recorded pure seismic and air-to-ground coupled waves. Air-to-sea coupling likely contributed to fast-arriving tsunamis. In this article, we highlight exceptional observations of the atmospheric waves.

58 GEOSCIENCES↗

Modeling Subsurface Explosions Recorded on a Distributed Fiber Optic Sensor

Fiber optic distributed acoustic sensors (DAS) are becoming a widely used tool for seismic sensing. Here we examine recordings of two subsurface chemical explosions, DAG-1 and DAG-3, each of which was about one metric ton (TNT equivalent), that were recorded from a helical fiber installed in two boreholes 80 m away from the source location. Several clear phases including the initial P wave, a weak S wave, and a surface reflected P wave are observed on the helical DAS data. We estimate a velocity model using arrival times measured from the fiber. The DAS waveform data were compared with colocated accelerometers at specific depths in both frequency and time domains. Furthermore, the spectra of the DAS data matched spectra estimated from the accelerometer records. Comparisons of observed waveform shape between the accelerometer records and the fiber measurements (strain-rate) show reasonable agreement except for the data near the event depth. The DAS data and the accelerometer agreed in relative amplitudes but we had difficulties in matching absolute amplitudes, possibly due to errors in metadata. Synthetic strain-rate waveforms were calculated using a 2D wavenumber algorithm and matched the waveform shape and relative amplitudes. In general, DAS is effective at recording strong ground motions at high spatial density. Comparison of the synthetic seismograms with observed data indicate that the waveforms are not consistent with a pure isotropic explosion source and that the observed S waves originate from very near the source region.

58 GEOSCIENCES↗

The Source Physics Experiment (SPE) Science Plan (Version 2.4c)

The Source Physics Experiment (SPE) series is a long-term NNSA research and development effort designed to improve U.S. arms control and nuclear nonproliferation verification and monitoring capabilities. The findings from the SPE will advance the United States’ nuclear explosion monitoring capabilities, particularly with respect to detection, discrimination and determination of yields associated with small nuclear explosions that can be lost amid the noisy seismo-acoustic background from other sources. The data generated from the SPE, a series of well-designed and recorded chemical explosions, will contribute to the development and validation of first-principles explosive source generated seismo-acoustic modeling codes. These codes will then facilitate the update of semi-empirical methods, currently based on historic test site data, such that key explosion observables can be reproduced, thus improving confidence in nuclear test monitoring in new areas and/or under novel emplacement conditions. The overall SPE project is comprised of both the development of the new explosion simulation codes and the chemical explosion test series. The chemical explosion test series will generate the empirical data required to both develop and validate the new simulation codes.

58 GEOSCIENCES↗

Absolute Locations of the North Korean Nuclear Tests Based on Differential Seismic Arrival Times and InSAR

Absolute location of the announced Democratic People’s Republic of Korea (DPRK) nuclear test on 6 January 2016 is constrained by fitting associated, Interferometric Synthetic Aperture Radar (InSAR)-based ground displacement with elastic finite-element modeling of an underground explosion source, including the effects of topography. The other five announced nuclear tests are located using arrival times and differential arrival times of regional and teleseismic body waves and constraints on the 6 January 2016 event location. Nuclear tests on 6 January 2016, 9 September 2016, and 3 September 2017 are under the summit ridge of Mt. Mantap, and tests on 25 May 2009 and 12 February 2013 are south of the topographic crest under the steep southern face of the mountain. The first test on 9 October 2006 was located near the crest of a separate topographic ridge approximately 2.87 km east of the 6 January 2016 event. Several unannounced events have occurred in the vicinity of the test site. The location uncertainty ellipse of an event approximately 8 min 30 s after the 2017 announced test covers the DPRK test site and is likely to have occurred there. Finally, additional events on 27 September 2017 and 12 October 2017 are 4–8 km northwest of the test site, and location probability regions do not overlap the test site.

58 GEOSCIENCES↗

Inferring Geothermal Reservoir Processes at the Raft River Geothermal Field, Idaho, USA, Through Modeling InSAR-Measured Surface Deformation

Ground surface deformations detected with Interferometric Synthetic Aperture Radar (InSAR) provide valuable information for inferring subsurface reservoir processes that are difficult to observe directly. This study aims at building a reservoir model that honors the available geological, hydrological and geo-mechanical data and also produces ground surface deformation consistent with InSAR measurements at the Raft River Geothermal Field. In the thermo-hydro-mechanical (THM) coupled model developed, the reservoir deforms as a result of the rock’s poroelastic response to changes in hydrologic pressure and thermal expansion/contraction. The results indicate that the observed deformation is the result of pressure decrease in the deep production reservoir and pressure increase in a shallower reservoir that accommodates the injected fluid (likely in the Salt Lake Formation). The combination of the uplift around injection wells with subsidence around the production wells, affected by the Bridge Fault as a flow barrier, creates a complex pattern of surface deformation in which the center of subtle subsidence significantly deviates from the location of the production wells. A parametric study suggests that (1) the Bridge Fault Zone is likely a flow barrier, (2) the surface deformation appears to be insensitive to the presence of the Narrows Structure, and (3) additional flow barriers likely exist to shape the flow system. This case study demonstrates the utility of a high-fidelity forward model that honors available known information and THM coupled processes in understanding geothermal reservoir characteristics.

58 GEOSCIENCES↗

Ground motion response to an ML 4.3 earthquake using co-located distributed acoustic sensing and seismometer arrays

The PoroTomo research team deployed two arrays of seismic sensors in a natural laboratory at Brady Hot Springs, Nevada in March 2016. The 1500 m (length) by 500 m (width) by 400 m (depth) volume of the laboratory overlies a geothermal reservoir. The surface Distributed Acoustic Sensing (DAS) array consisted of 8700 m of fiber-optic cable in a shallow trench, including 340 m in a well. The conventional seismometer array consisted of 238 three- component geophones. The DAS cable was laid out in three parallel zig-zag lines with line segments approximately 100 meters in length and geophones were spaced at approximately 60- meter intervals. Both DAS and conventional geophones recorded continuously over 15 days during which a moderate-sized earthquake with a local magnitude of 4.3 was recorded on March 21, 2016. Its epicenter was approximately 150-km south-southeast of the laboratory. Several DAS line segments with co-located geophone stations were used to compare signal-to-noise (SNR) ratios in both time and frequency domains and to test relationships between DAS and geophone data. The ratios were typically within a factor of five of each other with DAS SNR often greater for P-wave but smaller for S-wave relative to geophone SNR. The SNRs measured for an earthquake can be better than for active sources, because the earthquake signal contains more low frequency energy and the noise level is also lower at those lower frequencies. Amplitudes of the sum of several DAS strain-rate waveforms matched the finite difference of two geophone waveforms reasonably well, as did the amplitudes of DAS strain waveforms with particle-velocity waveforms recorded by geophones. Similar agreement was found between DAS and geophone observations and synthetic strain seismograms. In conclusion, the combination of good SNR in the seismic frequency band, high-spatial density, large N, and highly accurate time control among individual sensors suggests that DAS arrays have potential to assume a role in earthquake seismology.

60 signal-to-noise ratio↗

Walker Ranch 3D seismic images

Amplitude images (both vertical and depth slices) extracted from 3D seismic reflection survey over area of Walker Ranch area (adjacent to Raft River). Crossline spacing of 660 feet and inline of 165 feet using a Vibroseis source. Processing included depth migration. Micro-earthquake hypocenters on images. Stratigraphic information and nearby well tracks added to images. Images are embedded in a Microsoft Word document with additional information. Exact location and depth restricted for proprietary reasons. Data collection and processing funded by Agua Caliente. Original data remains property of Agua Caliente.

15 GEOTHERMAL ENERGY↗

Analysis of Ground Motion from An Underground Chemical Explosion

Here in this paper we investigate the excitation and propagation of far-field seismic waves from the 905 kg trinitrotoluene equivalent underground chemical explosion SPE-3 recorded during the Source Physics Experiment (SPE) at the Nevada National Security Site. The recorded far-field ground motion at short and long distances is characterized by substantial shear-wave energy, and large azimuthal variations in P-and S-wave amplitudes. The shear waves observed on the transverse component of sensors at epicentral distances <50 m suggests they were generated at or very near the source. The relative amplitude of the shear waves grows as the waves propagate away from the source. We analyze and model the shear-wave excitation during the explosion in the 0.01–10 Hz frequency range, at epicentral distances of up to 1 km. We used two simulation techniques. One is based on the empirical isotropic Mueller–Murphy (MM) (Mueller and Murphy, 1971) nuclear explosion source model, and 3D anelastic wave propagation modeling. The second uses a physics-based approach that couples hydrodynamic modeling of the chemical explosion source with anelastic wave propagation modeling. Comparisons with recorded data show the MM source model overestimates the SPE-3 far-field ground motion by an average factor of 4. The observations show that shear waves with substantial high-frequency energy were generated at the source. However, to match the observations additional shear waves from scattering, including surface topography, and heterogeneous shallow structure contributed to the amplification of far-field shear motion. Comparisons between empirically based isotropic and physics-based anisotropic source models suggest that both wave-scattering effects and near-field nonlinear effects are needed to explain the amplitude and irregular radiation pattern of shear motion observed during the SPE-3 explosion.

58 GEOSCIENCES↗

Passive seismic investigation of Harrat Rahat

Ambient noise correlation was applied to 18 months of continuous seismic data from 14 stations. The procedure of Bensen et al [2007] was followed with some changes to optimize signal-to-noise of the results. The 18 months of correlations (representing about 1 week of CPU time on a 12 core machine) were stacked and manually inspected to yield about 40 cross-correlations. These cross-correlations represent the Green’s function between the station pairs and will be analyzed in part two of this project to yield velocity structure.

15 GEOTHERMAL ENERGY↗

An efficient optimization of well placement and control for a geothermal prospect under geological uncertainty

This work applies an efficient optimization technique based on a multivariate adaptive regression spline (MARS) technique to determine the optimal design and engineering of a potential geothermal production operation at a prospect near Superstition Mountain in Southern California, USA. The faster MARS-based statistical model is used as a surrogate for higher-fidelity physical models within the intensive optimization process. Its use allows for the exploration of the impacts of specific engineering design parameters in the context of geologic uncertainty as a means to both understand and maximize profitability of the production operation. The MARS model is initially developed from a training dataset generated by a finite set of computationally complex hydrothermal models applied to the prospect. Its application reveals that the optimal engineering design variables can differ considerably assuming different choices of hydrothermal flow properties, which, in turn, indicates the importance of reducing the uncertainty of key geologic properties. The major uncertainty sources in the natural-system are identified and ranked first by an efficient MARS-enabled total order sensitivity quantification, which is then used to assist evaluating the effect of geological uncertainties on optimized results. At the Southern California prospect, this parameter sensitivity analysis suggests that groundwater circulation through high permeable structures, rather than heat conduction through impermeable granite, is the primary heat transfer method during geothermal extraction. Reservoir histories simulated using optimal parameters with different constraints are analyzed and compared to investigate the longevity and maximum profit of the geothermal resources. The comparison shows that the longevity and profit are very likely to be overestimated by optimizations without appropriate constraints on natural conditions. In addition to geothermal energy production, this optimization approach can also be used to manage other geologic resource operations, such as hydrocarbon production or CO 2 sequestration, under uncertain reservoir conditions.

15 GEOTHERMAL ENERGY↗

An efficient Bayesian inversion of a geothermal prospect using a multivariate adaptive regression spline method

In this study, an efficient Bayesian framework equipped with a multivariate adaptive regression spline (MARS) technique is developed to alleviate computational burdens encountered in a conventional Bayesian inversion of a geothermal prospect. Fast MARS models are developed from training dataset generated by CPU-intensive hydrothermal models and used as surrogate of high-fidelity physical models in Markov Chain Monte Carlo (MCMC) sampling. This Bayesian inference with MARS-enabled MCMC method is used to reduce prior estimates of uncertainty in structural or characteristic hydrothermal flow parameters of the model to posterior distributions. A geothermal prospect near Superstition Mountain in Imperial County of California in USA is used to illustrate the proposed framework and demonstrate the computational efficiency of MARS-based Bayesian inversion. The developed MARS models are also used to efficiently drive calculation of Sobol’ total sensitivity indices. Furthermore, only top sensitive parameters are included in Bayesian inference to further improve the computational efficiency of inversion. Sensitivity analysis also confirms that water circulation through high permeable structures, rather than heat conduction through impermeable granite, is the primary heat transfer method. The presented framework is demonstrated an efficient tool to update knowledge of geothermal prospects by inversing field data. Although only thermal data is used in this study, other type of data, such as flow and transport observations, can be jointly used in this method for underground hydrocarbon reservoirs.

15 GEOTHERMAL ENERGY↗

Brady 1D seismic velocity model ambient noise prelim

Preliminary 1D seismic velocity model derived from ambient noise correlation. 28 Green's functions filtered between 4-10 Hz for Vp, Vs, and Qs were calculated. 1D model estimated for each path. The final model is a median of the individual models. Resolution is best for the top 1 km. Poorly constrained with increasing depth.

15 GEOTHERMAL ENERGY↗

Chemical Explosion Experiments to Improve Nuclear Test Monitoring [Developing a New Paradigm for Nuclear Test Monitoring with the Source Physics Experiments (SPE)]

A series of chemical explosions, called the Source Physics Experiments (SPE), is being conducted under the auspices of the U.S. Department of Energy’s National Nuclear Security Administration (NNSA) to develop a new more physics-based paradigm for nuclear test monitoring. Currently, monitoring relies on semi-empirical models to discriminate explosions from earthquakes and to estimate key parameters such as yield. While these models have been highly successful monitoring established test sites, there is concern that future tests could occur in media and at scale depths of burial outside of our empirical experience. This is highlighted by North Korean tests, which exhibit poor performance of a reliable discriminant, mb:Ms (Selby et al., 2012), possibly due to source emplacement and differences in seismic responses for nascent and established test sites. The goal of SPE is to replace these semi-empirical relationships with numerical techniques grounded in a physical basis and thus applicable to any geologic setting or depth.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗