Search NASA⌕ Search

Engineering topics

Mendenhall, Michael R.

Publications and source records attributed to Mendenhall, Michael R..

18 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Application of System Identification to Parachute Modeling

Parachute models are used in numerous flight simulation tools to predict a wide range of parachute flight performance characteristics (e.g., parachute inflation loads, parachute stability and dynamics, vehicle touchdown conditions, and, ultimately, the safety and survivability of the system using the parachute). The current state of the art in developing parachute models is to initially estimate the parachute characteristics based on the parachute geometry and historical data and then add increased model fidelity based on data from wind tunnel and/or flight tests. This approach, however, can be deficient in identifying which parachute states (e.g., angle of attack, sideslip, angular rates, flyout angles, descent rate, dynamic pressure, proximity to other parachutes) are responsible for the parachute motion, and the relationship between those states and the forces on the parachute.

Murri, Daniel G.↗
NASA NTRS2016

Wake-Induced Aerodynamics on a Trailing Aircraft

NASA conducted flight tests to measure the exhaust products from alternative fuels using a DC-8 transport aircraft and a Falcon business jet. An independent analysis of the maximum vortex-induced loads on the Falcon in the DC-8 wake was conducted for pre-flight safety analysis and to define safe trail distances for the flight tests. Static and dynamic vortex-induced aerodynamic loads on the Falcon were predicted at a matrix of locations aft of the DC-8 under flight-test conditions, and the maximum loads were compared with design limit loads to assess aircraft safety. Trajectory simulations for the Falcon during close encounters with the DC-8 wake were made to study the vortex-induced loads during traverses of the DC-8 primary trailing vortex. A parametric study of flight traverses through the trailing vortex was conducted to assess Falcon flight behavior and motion characteristics.

Mendenhall, Michael R.↗
NASA NTRS2015

Trailing Vortex-Induced Loads During Close Encounters in Cruise

The trailing vortex induced aerodynamic loads on a Falcon 20G business jet flying in the wake of a DC-8 are predicted to provide a preflight estimate of safe trail distances during flight test measurements in the wake. Static and dynamic loads on the airframe flying in the near wake are shown at a matrix of locations, and the dynamic motion of the Falcon 20G during traverses of the DC-8 primary trailing vortex is simulated. Safe trailing distances for the test flights are determined, and optimum vortex traverse schemes are identified to moderate the motion of the trailing aircraft during close encounters with the vortex wake.

Mendenhall, Michael R.↗
NASA NTRS2011

Grid Fin Stabilization of the Orion Launch Abort Vehicle

Wind tunnel tests were conducted by Nielsen Engineering & Research (NEAR) and Rose Engineering & Research (REAR) in conjunction with the NASA Engineering & Safety Center (NESC) on a 6%-scale model of the Orion launch abort vehicle (LAV) configured with four grid fins mounted near the base of the vehicle. The objectives of these tests were to 1) quantify LAV stability augmentation provided by the grid fins from subsonic through supersonic Mach numbers, 2) assess the benefits of swept grid fins versus unswept grid fins on the LAV, 3) determine the effects of the LAV abort motors on grid fin aerodynamics, and 4) generate an aerodynamic database for use in the future application of grid fins to small length-to-diameter ratio vehicles similar to the LAV. The tests were conducted in NASA Ames Research Center's 11x11-foot transonic wind tunnel from Mach 0.5 through Mach 1.3 and in their 9x7-foot supersonic wind tunnel from Mach 1.6 through Mach 2.5. Force- and moment-coefficient data were collected for the complete vehicle and for each individual grid fin as a function of angle of attack and sideslip angle. Tests were conducted with both swept and unswept grid fins with the simulated abort motors (cold jets) off and on. The swept grid fins were designed with a 22.5deg aft sweep angle for both the frame and the internal lattice so that the frontal projection of the swept fins was the same as for the unswept fins. Data from these tests indicate that both unswept and swept grid fins provide significant improvements in pitch stability as compared to the baseline vehicle over the Mach number range investigated. The swept fins typically provide improved stability as compared to the unswept fins, but the performance gap diminished as Mach number was increased. The aerodynamic performance of the fins was not observed to degrade when the abort motors were turned on. Results from these tests indicate that grid fins can be a robust solution for stabilizing the Orion LAV over a wide range of operating conditions.

Pruzan, Daniel A.↗
NASA NTRS2004

A Best Practices System to Enhance CFD Use in Stability and Control Applications

Successful use of CFD to provide aerodynamics for stability and control (S&C) applications will require that the traditional time and costs associated with CFD be reduced and that the errors and uncertainties currently associated with CFD be better understood. CFD will be required to work under a wide range of flow conditions and provide fast and reliable aerodynamics if it is to contribute to this next generation of S&C analyses. CFD solutions have errors and uncertainties due to poorly converged solutions, solution anomalies caused by grids, turbulence models, and parameter selection, and other manifold reasons. In addition to the above problems, there will be a requirement for communications between the CFD expert and the S&C expert and possibly experts from other related disciplines. The CFD expert may not understand the technical problems associated with S&C, and it is almost certain the converse is true.

Morrison, Joseph H.↗
NASA NTRS2003

Best Practices for Reduction of Uncertainty in CFD Results

This paper describes a proposed best-practices system that will present expert knowledge in the use of CFD. The best-practices system will include specific guidelines to assist the user in problem definition, input preparation, grid generation, code selection, parameter specification, and results interpretation. The goal of the system is to assist all CFD users in obtaining high quality CFD solutions with reduced uncertainty and at lower cost for a wide range of flow problems. The best-practices system will be implemented as a software product which includes an expert system made up of knowledge databases of expert information with specific guidelines for individual codes and algorithms. The process of acquiring expert knowledge is discussed, and help from the CFD community is solicited. Benefits and challenges associated with this project are examined.

Mendenhall, Michael R.↗
NASA NTRS1995

Experimental Aerodynamic Characteristics of the Pegasus Air-Launched Booster and Comparisons with Predicted and Flight Results

Experimental longitudinal and lateral-directional aerodynamic characteristics were obtained for the Pegasus and Pegasus XL configurations over a Mach number range from 1.6 to 6 and angles of attack from -4 to +24 degrees. Angle of sideslip was varied from -6 to +6 degrees, and control surfaces were deflected to obtain elevon, aileron, and rudder effectiveness. Experimental data for the Pegasus configuration are compared with engineering code predictions performed by Nielsen Engineering & Research, Inc. (NEAR) in the aerodynamic design of the Pegasus vehicle, and with results from the Aerodynamic Preliminary Analysis System (APAS) code. Comparisons of experimental results are also made with longitudinal flight data from Flight #2 of the Pegasus vehicle. Results show that the longitudinal aerodynamic characteristics of the Pegasus and Pegasus XL configurations are similar, having the same lift-curve slope and drag levels across the Mach number range. Both configurations are longitudinally stable, with stability decreasing towards neutral levels as Mach number increases. Directional stability is negative at moderate to high angles of attack due to separated flow over the vertical tail. Dihedral effect is positive for both configurations, but is reduced 30-50 percent for the Pegasus XL configuration because of the horizontal tail anhedral. Predicted longitudinal characteristics and both longitudinal and lateral-directional control effectiveness are generally in good agreement with experiment. Due to the complex leeside flowfield, lateral-directional characteristics are not as well predicted by the engineering codes. Experiment and flight data are in good agreement across the Mach number range.

Rhode, M. N.↗
NASA NTRS1993

In-flight evaluation of aerodynamic predictions of an air-launched space booster

Several analytical aerodynamic design tools that were applied to the Pegasus air-launched space booster were evaluated using flight measurements. The study was limited to existing codes and was conducted with limited computational resources. The flight instrumentation was constrained to have minimal impact on the primary Pegasus missions. Where appropriate, the flight measurements were compared with computational data. Aerodynamic performance and trim data from the first two flights were correlated with predictions. Local measurements in the wing and wing-body interference region were correlated with analytical data. This complex flow region includes the effect of aerothermal heating magnification caused by the presence of a corner vortex and interaction of the wing leading edge shock and fuselage boundary layer. The operation of the first two missions indicates that the aerodynamic design approach for Pegasus was adequate, and data show that acceptable margins were available. Additionally, the correlations provide insight into the capabilities of these analytical tools for more complex vehicles in which design margins may be more stringent.

Curry, Robert E.↗
NASA NTRS1993

Aerodynamic analysis of Pegasus - Computations vs reality

Pegasus, a three-stage, air-launched, winged space booster was developed to provide fast and efficient commercial launch services for small satellites. The aerodynamic design and analysis of Pegasus was conducted without benefit of wind tunnel tests using only computational aerodynamic and fluid dynamic methods. Flight test data from the first two operational flights of Pegasus are now available, and they provide an opportunity to validate the accuracy of the predicted pre-flight aerodynamic characteristics. Comparisons of measured and predicted flight characteristics are presented and discussed. Results show that the computational methods provide reasonable aerodynamic design information with acceptable margins. Post-flight analyses illustrate certain areas in which improvements are desired.

Mendenhall, Michael R.↗
NASA NTRS1992

Prediction of vortex shedding from forebodies with chines

An engineering prediction method and associated computer code VTXCHN to predict nose vortex shedding from circular and noncircular forebodies with sharp chines edges in subsonic flow at angles of attack and roll are presented. Axisymmetric bodies are represented by point sources and doublets, and noncircular cross sections are transformed to a circle by either analytical or numerical conformal transformations. The lee side vortex wake is modeled by discrete vortices in crossflow planes along the body; thus the three-dimensional steady flow problem is reduced to a two-dimensional, unsteady, separated flow problem for solution. Comparison of measured and predicted pressure distributions, flow field surveys, and aerodynamic characteristics are presented for noncircular bodies alone and forebodies with sharp chines.

Mendenhall, Michael R.↗
NASA NTRS1992

In-flight Evaluation of Aerodynamic Predictions of an Air-launched Space Booster

Several analytical aerodynamic design tools that were applied to the Pegasus (registered trademark) air-launched space booster were evaluated using flight measurements. The study was limited to existing codes and was conducted with limited computational resources. The flight instrumentation was constrained to have minimal impact on the primary Pegasus missions. Where appropriate, the flight measurements were compared with computational data. Aerodynamic performance and trim data from the first two flights were correlated with predictions. Local measurements in the wing and wing-body interference region were correlated with analytical data. This complex flow region includes the effect of aerothermal heating magnification caused by the presence of a corner vortex and interaction of the wing leading edge shock and fuselage boundary layer. The operation of the first two missions indicates that the aerodynamic design approach for Pegasus was adequate, and data show that acceptable margins were available. Additionally, the correlations provide insight into the capabilities of these analytical tools for more complex vehicles in which the design margins may be more stringent.

Curry, Robert E.↗
NASA NTRS1992

Vortex cloud model for body vortex shedding and tracking

The present engineering prediction method addresses the aerodynamic characteristics and associated flowfields of circular and noncircular bodies at large incidence angles and arbitrary roll angles. 3D attached-flow models are used to represent the body, and 2D, incompressible, separated flow models are used to represent the separated vortex wake. The predicted pressure distribution of the body, under the influence of both the freestream and the separation vortex wake, is used to calculate aerodynamic loads. The separation vortex wake is represented by clouds of discrete vortices in crossflow planes normal to the body axis.

Mendenhall, Michael R.↗
NASA NTRS1990

Prediction of subsonic vortex shedding from forebodies with chines

An engineering prediction method and associated computer code VTXCHN to predict nose vortex shedding from circular and noncircular forebodies with sharp chine edges in subsonic flow at angles of attack and roll are presented. Axisymmetric bodies are represented by point sources and doublets, and noncircular cross sections are transformed to a circle by either analytical or numerical conformal transformations. The lee side vortex wake is modeled by discrete vortices in crossflow planes along the body; thus the three-dimensional steady flow problem is reduced to a two-dimensional, unsteady, separated flow problem for solution. Comparison of measured and predicted surface pressure distributions, flow field surveys, and aerodynamic characteristics are presented for noncircular bodies alone and forebodies with sharp chines.

Mendenhall, Michael R.↗
NASA NTRS1990

Prediction of vortex shedding from forebodies with chines

An engineering prediction method to calculate vortex shedding from noncircular forebodies with sharp chine edges in subsonic flow at large incidence angles is presented. The forebody is represented by two- and three-dimensional singularities, and the lee side vortex wake is modeled by discrete vortices in crossflow planes along the body. The computational procedure is described, and comparisons of measured and predicted surface pressure distributions and predicted flow field vectors are presented to illustrate the method.

Mendenhall, Michael R.↗
NASA NTRS1987

Prediction of vortex shedding from circular and noncircular bodies in subsonic flow

An engineering prediction method and associated computer code VTXCLD are presented which predict nose vortex shedding from circular and noncircular bodies in subsonic flow at angles of attack and roll. The axisymmetric body is represented by point sources and doublets, and noncircular cross sections are transformed to a circle by either analytical or numerical conformal transformations. The leeward vortices are modeled by discrete vortices in crossflow planes along the body; thus, the three-dimensional steady flow problem is reduced to a two-dimensional, unsteady, separated flow problem for solution. Comparison of measured and predicted surface pressure distributions, flowfield surveys, and aerodynamic characteristics are presented for bodies with circular and noncircular cross sectional shapes.

Mendenhall, Michael R.↗
NASA NTRS1987

Aerodynamic characteristics of cruciform missiles at high angles of attack

An aerodynamic prediction method for missile aerodynamic performance and preliminary design has been developed to utilize a newly available systematic fin data base and an improved equivalent angle of attack methodology. The method predicts total aerodynamic loads and individual fin forces and moments for body-tail (wing-body) and canard-body-tail configurations with cruciform fin arrangements. The data base and the prediction method are valid for angles of attack up to 45 deg, arbitrary roll angles, fin deflection angles between -40 deg and 40 deg, Mach numbers between 0.6 and 4.5, and fin aspect ratios between 0.25 and 4.0. The equivalent angle of attack concept is employed to include the effects of vorticity and geometric scaling.

Lesieutre, Daniel J.↗
NASA NTRS1986

Vortex cloud model for body vortex shedding and tracking

The discrete vortex cloud approach models a missile airframe's vortex wake by means that are capable of treating a variety of configurations over a range of flow conditions. Attention is given to the sheets of vorticity formed on the lee side of a missile at moderate angles-of-attack. While three-dimensional attached flow models are used to represent the missile body, two-dimensional, incompressible, separated flow models are used to represent the separated vortex wake. The predicted pressure distribution of the body under the influence of the freestream and the separation vortex wake are used to calculate aerodynamic loads on the body. The separation vortex wake is represented by clouds of discrete vortices in cross flow planes normal to the body axis.

Mendenhall, Michael R.↗