Engineering topics

Meng, Huifeng

Publications and source records attributed to Meng, Huifeng.

4 records

DOE OSTI2023

Sequential Deposition of Multicomponent Bulk Heterojunctions Increases Efficiency of Organic Solar Cells

Constructing tandem and multi-blend organic solar cells (OSCs) is an effective way to overcome the absorption limitations of conventional single-junction devices. However, these methods inevitably require tedious multilayer deposition or complicated morphology-optimization procedures. Herein, sequential deposition is utilized as an effective and simple method to fabricate multicomponent OSCs with a double-bulk heterojunction (BHJ) structure of the active layer to further improve photovoltaic performance. Two efficient donor-acceptor pairs, D18-Cl:BTP-eC9 and PM6:L8-BO, are sequentially deposited to form the D18-Cl:BTP-eC9/PM6:L8-BO double-BHJ active layer. In these double-BHJ OSCs, light absorption is significantly improved, and optimal morphology is also retained without requiring a more complicated morphology optimization involved in quaternary blends. Compared to the quaternary blend devices, energy loss (E loss ) is also reduced by rationally matching each donor with an appropriate acceptor. Consequently, the power conversion efficiency (PCE) is improved from 18.25% for D18-Cl:BTP-eC9 and 18.69% for PM6:L8-BO based binary blend OSCs to 19.61% for the double-BHJ OSCs. In contrast, a D18-Cl:PM6:L8-BO:BTP-eC9 quaternary blend of OSCs exhibited a dramatically reduced PCE of 15.83%. Finally, these results demonstrate that a double-BHJ strategy, with a relatively simple processing procedure, can potentially enhance the device performance of OSCs and lead to more widespread use.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Binary Blend All‐Polymer Solar Cells with a Record Efficiency of 17.41% Enabled by Programmed Fluorination Both on Donor and Acceptor Blocks

Abstract Despite remarkable breakthrough made by virtue of “polymerized small‐molecule acceptor (PSMA)” strategy recently, the limited selection pool of high‐performance polymer acceptors and long‐standing challenge in morphology control impede their further developments. Herein, three PSMAs of PYDT‐2F, PYDT‐3F, and PYDT‐4F are developed by introducing different fluorine atoms on the end groups and/or bithiophene spacers to fine‐tune their optoelectronic properties for high‐performance PSMAs. The PSMAs exhibit narrow bandgap and energy levels that match well with PM6 donor. The fluorination promotes the crystallization of the polymer chain for enhanced electron mobility, which is further improved by following n ‐doping with benzyl viologen additive. Moreover, the miscibility is also improved by introducing more fluorine atoms, which promotes the intermixing with PM6 donor. Among them, PYDT‐3F exhibits well‐balanced high crystallinity and miscibility with PM6 donor; thus, the layer‐by‐layer processed PM6/PYDT‐3F film obtains an optimal nanofibril morphology with submicron length and ≈23 nm width of fibrils, facilitating the charge separation and transport. The resulting PM6/PYDT‐3F devices realizes a record high power conversion efficiency (PCE) of 17.41% and fill factor of 77.01%, higher than the PM6/PYDT‐2F (PCE = 16.25%) and PM6/PYDT‐4F (PCE = 16.77%) devices.

Zhou, Dehong↗

DOE OSTI2022

Unique W-Shape Y6 isomer as effective solid additive for High-Performance PM6:Y6 polymer solar cells

The current top-performing polymer solar cell (PSC) systems are mostly based on PM6:Y6 host blend. To date, numerous materials have been explored as the third component for these systems to form ternary blends or as additives. Vitrification agents are a group of additives proved to be useful in affecting the morphology of organic semiconductors. Here to design a suitable vitrification agent for non-fullerene electron acceptor Y6, an isomer strategy was explored where the thienothiophene wings of the Y6 molecule were inversed to form a W-shaped Y6 isomer of i-Y6. It was found that i-Y6 crystallized poorly with a different packing style than Y6 and could blend well in amorphous phase of Y6. These properties enabled i-Y6 to finely tune the morphology of PM6:Y6 blend at low additive dosages. The power conversion efficiency (PCE) of PM6:Y6 based PSC was raised from 16.827% to 17.433% at a dosage of Y6:i-Y6 ratio of 24:1. This work demonstrated isomerization as a viable strategy for developing solid additives for high performance PSC blends and vitrification agents as effective additives for tuning morphology and improving performances of PSCs.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Polymer Solar Cells with 18.74% Efficiency: From Bulk Heterojunction to Interdigitated Bulk Heterojunction

The most popular approach to fabricating organic solar cells (OSCs) is solution processing a mixture of donor (D) and acceptor (A) materials into an active layer with a bulk heterojunction (BHJ) nanostructure. In this work, it is demonstrated that the interdigitated heterojunction (IHJ) is a more suitable nanostructure of the active layer for high-performance OSCs whereas it is a long standing challenge to realize well-defined IHJ structures. Here, a facile and versatile sequential solution processing method is developed to produce an IHJ nanostructure with power conversion efficiency reaching 18.74% (18.10% for BHJ the counterpart) by fabricating a donor film with nanopores created by a wax additive, sequentially casting the acceptor on top of infiltrating the nanopores. Compared to the BHJ, the IHJ structure with an interpillar distance within the exciton diffusion length can afford a large bulk D/A interface for efficient exciton dissociation with a minimized charge recombination while free electrons and holes can transport to the respective electrodes through more straightforward pathways, thus enhance performance. Furthermore, the D or A phase in the IHJ device contacts with only one electrode, which can prevent shunting between the anode and cathode and facilitate the industrial mass production of OSCs.

36 MATERIALS SCIENCE↗