Search NASA⌕ Search

Engineering topics

Meng, Lingyi

Publications and source records attributed to Meng, Lingyi.

Experimental study of the influence of gas puff locations on H-mode boundary plasmas with argon seeding on EAST

To investigate the optimal scenario of impurity seeding to obtain divertor plasma detachment for target protection, experiments with Ar&D 2 seeding from two different poloidal locations, the upper outer (UO) divertor target and lower outer (LO) target, were carried out on EAST. Partial energy detachment (the electron temperature near the strike point T e,spt ≤ 10 eV) were obtained with Ar&D 2 mixture puffing from the UO target and, for the first time, from the LO target into H-mode plasmas in the upper single null (USN) configuration. The peak heat flux q t on the UO target was significantly reduced (by ~80%). The rollover of ion flux density j s did not appear probably due to insufficient momentum loss, which is independent of the puff locations. The poloidal asymmetries of particle and heat fluxes on the targets have also been investigated. The UO-dominant asymmetry of particle flux was reversed, while the UO-dominant asymmetry of heat flux was mitigated but not reversed. The plasma confinement dropped by only 14% and 8.2% in the LO-puff case and UO-puff case, respectively, during detachment. The high level of C may contributed greatly to the higher radiation in the bulk plasma region and the greater decline in W MHD in the LO-puff case.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Comparison of divertor behavior and plasma confinement between argon and neon seeding in EAST

The exhaust of excessively high heat and particle fluxes on the divertor target is crucial for EAST long-pulse operation. In the recent EAST experiments, stable partial energy detachment around the upper outer strike point with H 98,y2 ~ 1 was achieved with either Ne or Ar seeding from the upper outer divetor target in the upper single null configuration with ITER-like tungsten divertor. With either Ar or Ne seeding, the electron temperature around the upper outer strike point (T et,UOSP ) was maintained at around 5 eV, the peak temperature of divertor target surface around the upper outer strike point (T div,UO ) decreased significantly, and material sputtering was well suppressed. Here, it was observed that there was less Ar seeding needed for partial energy detachment onset than Ne seeding, which shows that Ar is more efficient in the cooling of T et on the upper outer divertor than Ne. However, there was no detachment on the upper inner divertor with T et around strike point (T et,UISP ) remaining >10 eV with either Ar or Ne seeding from the upper outer divertor. Accompanied with the disappearance of double peak phenomenon of ion flux density on the upper inner divertor target (j s,UI ), the peak T div,UI around the strike point increased to around 300 °C. Although the heat flux on the upper inner divertor target (q t,UI ) is still in the acceptable level, either Ar or Ne seeding only from the upper outer divertor target is not enough to protect the upper inner divertor target from sputtering under current EAST conditions. On the other hand, Ar seeding always causes confinement degradation in the partial energy detachment state. It was observed that there is a slight confinement improvement (~10%) with Ne seeding, which may be due to density peaking, dilution effects and stabilization of the ion temperature gradient mode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Frequency-domain multiscale quantum mechanics/electromagnetics simulation method

A frequency-domain quantum mechanics and electromagnetics (QM/EM) method is developed. Compared with the time-domain QM/EM method [Meng et al., J. Chem. Theory Comput. 8, 1190–1199 (2012)], the newly developed frequency-domain QM/EM method could effectively capture the dynamic properties of electronic devices over a broader range of operating frequencies. The system is divided into QM and EM regions and solved in a self-consistent manner via updating the boundary conditions at the QM and EM interface. The calculated potential distributions and current densities at the interface are taken as the boundary conditions for the QM and EM calculations, respectively, which facilitate the information exchange between the QM and EM calculations and ensure that the potential, charge, and current distributions are continuous across the QM/EM interface. Via Fourier transformation, the dynamic admittance calculated from the time-domain and frequency-domain QM/EM methods is compared for a carbon nanotube based molecular device.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗