Search NASA⌕ Search

Engineering topics

Mercer, C. E.

Publications and source records attributed to Mercer, C. E..

18 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Pitot-Pressure Measurements in Flow Fields Behind a Rectangular Nozzle with Exhaust Jet for Free-Stream Mach Numbers of 0.00, 0.60, and 1.20

An investigation has been conducted in the Langley 16-Foot Transonic Tunnel to measure the flow field in and around the jet exhaust from a nonaxisymmetric nozzle configuration. The nozzle had a rectangular exit with a width-to-height ratio of 2.38. Pitot-pressure measurements were made at five longitudinal locations downstream of the nozzle exit. The maximum distance downstream of the exit was about 5 nozzle heights. These measurements were made at free-stream Mach numbers of 0.00, 0.60, and 1.20 with the nozzle operating at a ratio of nozzle total pressure to free-stream static pressure of 4.0. The jet exhaust was simulated with high-pressure air that had an exit total temperature essentially equal to the free-stream total temperature.

Putnam, L. E.↗
NASA NTRS1986

Forward-swept wing configuration designed for high maneuverability by use of a transonic computational method

A transonic computational analysis method and a transonic design procedure have been used to design the wing and the canard of a forward-swept-wing fighter configuration for good transonic maneuver performance. A model of this configuration was tested in the Langley 16-Foot Transonic Tunnel. Oil-flow photographs were obtained to examine the wind flow patterns at Mach numbers from 0.60 to 0.90. The transonic theory gave a reasonably good estimate of the wing pressure distributions at transonic maneuver conditions. Comparison of the forward-swept-wing configuration with an equivalent aft-swept-wing-configuration showed that, at a Mach number of 0.90 and a lift coefficient of 0.9, the two configurations have the same trimmed drag. The forward-swept wing configuration was also found to have trimmed drag levels at transonic maneuver conditions which are comparable to those of the HiMAT (highly maneuverable aircraft technology) configuration and the X-29 forward-swept-wing research configuration. The configuration of this study was also tested with a forebody strake.

Mann, M. J.↗
NASA NTRS1985

Performance characteristics of an isolated coannular plug nozzle at transonic speeds

The Langley 16-Foot Transonic Tunnel was used to evaluate the performance characteristics of a coannular plug nozzle at static conditions (Mach number of 0) and at Mach numbers from 0.65 to 1.20. Jet total pressure ratio was varied from 1.0 (jet off) to 10.0. Thirty-seven configurations generated by the combination of three geometric variables - plug angle, shroud boattail length (fixed exit radius), and shroud extension length - were tested.

Mercer, C. E.↗
NASA NTRS1985

A forward-swept wing configuration designed for high maneuverability by use of three-dimensional transonic theory

Supercritical technology has been applied to the design of a forward-swept-wing fighter configuration, and an assessment has been made of the relative performance of forward versus aft sweep. The wing and canard for this forward-swept wing configuration were designed for transonic maneuver by the use of a transonic computational analysis method and a transonic design procedure. The computational method calculates the transonic flow over a canard-wing-fuselage combination so that the strong transonic induced-flow effects of the canard on the wing are taken into account. A model of this configuration was constructed and was tested in the Langley 16-Foot Transonic Tunnel. The transonic theory gave a reasonably good estimate of the wing pressure distributions at transonic maneuver conditions. Comparison of this configuration with an equivalent aft-swept wing configuration showed that, at a Mach number of 0.9 and a lift coefficient of 0.9, the two configurations have essentially the same drag. This forward-swept wing configuration was also found to have very good maneuver performance relative to the Rockwell International HiMAT highly-maneuverable aircraft configuration.

Mann, M. J.↗
NASA NTRS1982

Supercritical maneuvering fighter configuration. Wind-tunnel investigation at Mach numbers of 0.60 to 0.95

A wind tunnel investigation was conducted to study the application of supercritical technology to highly maneuverable combat aircraft. The configuration studied has a leading-edge sweep of 45 deg and an aspect ratio of 3.28. Two supercritical-wing shapes were tested at Mach numbers from 0.60 to 0.95 with angles of attack from -2 deg to 17 deg. On supercritical wing was designed to achieve a high level of transonic maneuver performance at a Mach number of 0.90; however, excessive flow separation developed on this wing at a Mach number of 0.85. A second supercritical wing was tested which had significantly reduced flow separation and improved drag characteristics at a Mach number of 0.85 and maintained the performance of the original wing at the higher Mach numbers. Leading-edge vortex generators did not improve the performance of the second wing; however, a sharp leading-edge flap produced sizable drag reductions at Mach numbers from 0.60 to 0.90.

Mann, M. J.↗
NASA NTRS1979

Transonic aerodynamic characteristics of a supersonic cruise aircraft research model with the engines suspended above the wing

The influence of upper-surface nacelle exhaust flow on the aerodynamic characteristics of a supersonic cruise aircraft research configuration was investigated in a 16 foot transonic tunnel over a range of Mach numbers from 0.60 to 1.20. The arrow-wing transport configuration with engines suspended over the wing was tested at angles of attack from -4 deg to 6 deg and jet total pressure ratios from 1 to approximately 13. Wing-tip leading edge flap deflections of -10 deg to 10 deg were tested with the wing-body configuration. Various nacelle locations (chordwise, spanwise, and vertical) were tested over the ranges of Mach numbers, angles of attack, and jet total-pressure ratios. The results show that reflecting the wing-tip leading edge flap from 0 deg to -10 deg increased the maximum lift-drag ratio by 1.0 at subsonic speeds. Jet exhaust interference effects were negligible.

Mercer, C. E.↗
NASA NTRS1977

Investigation of effect of propulsion system installation and operation on aerodynamics of an airbreathing hypersonic airplane at Mach 0.3 to 1.2

Results from an investigation of the effects of the operation of a combined turbojet/scramjet propulsion system on the longitudinal aerodynamic characteristics of a 1/60-scale hypersonic airbreathing launch vehicle configuration are presented. Decomposition products of hydrogen peroxide were used for simulation of the propulsion system exhaust.

Cubbage, J. M.↗
NASA NTRS1976

Upper Surface Nacelle Influence on SCAR Aerodynamic Characteristics at Transonic Speeds

The arrow-wing transport configuration with detached engines located over the wing to produce upper surface exhaust flow effects was tested at angles of attack from -4 deg to 8 deg and jet total-pressure ratios from 1 (Jet off) to approximately 10. Wing tip leading edge flap deflections of -10 deg to 10 deg were tested with the wing-body configuration only (no nacelles). Tests were made with various nacelle chordwise, spanwise, and vertical height locations over the Mach number, angle of attack, and jet total-pressure ratio ranges. Deflecting the wing tip leading edge flap from 0 deg to -10 deg increased maximum lift to drag ratio by 1.0 at subsonic speeds. Installation of upper surface nacelles (no wing/nacelle pylons) increased the wing-body pitching moment at all Mach numbers and decreased the drag of the wing-body configuration at subsonic Mach numbers. Jet exhaust interference effects were negligible.

Mercer, C. E.↗
NASA NTRS1975

Effects of nozzle interfairing modifications on longitudinal aerodynamic characteristics of a twin jet, variable wing sweep fighter model

A wind-tunnel investigation has been made to determine the effects of nozzle interfairing modifications on the longitudinal aerodynamic characteristics of a twin-jet, variable-wing-sweep fighter model. The model was tested in the Langley 16-foot transonic tunnel at Mach numbers of 0.6 to 1.3 and angles of attack from about minus 2 deg to 6 deg and in the Langley 4-foot supersonic presure tunnel at a Mach number of 2.2 and an angle of attack of 0 deg. Compressed air was used to simulate nozzle exhaust flow at jet total-pressure ratios from 1 (jet off) to about 21. The results of this investigation show that the aircraft drag can be significantly reduced by replacing the basic interfairing with a modified interfairing.

Reubush, D. E.↗
NASA NTRS1974

Exhaust-nozzle characterisitcs for a twin-jet variable-wing-sweep fighter airplane model at Mach numbers to 2.2

A wind-tunnel investigation has been conducted to determine the exhaust-nozzle aerodynamic and propulsive characteristics for a twin-jet variable-wing-sweep fighter airplane model. The powered model was tested in the Langley 16-foot transonic tunnel and in the Langley 4-foot supersonic pressure tunnel at Mach numbers to 2.2 and at angles of attack from about minus 2 to 6 deg. Compressed air was used to simulate the nozzle exhaust flow at values of jet total-pressure ratio from approximately 1 (jet off) to about 21. Effects of configuration variables such as speed-brake deflection, store installation, and boundary-layer thickness on the the nozzle characteristics were also investigated.

Reubush, D. E.↗
NASA NTRS1972

Effect of jet convergence angle on the performance of annular nozzles with semitoroidal concave plugs at Mach numbers up to 1.82

Results of an investigation at static conditions and at Mach numbers up to 1.82 are presented for 12 nozzle configurations which have jet convergence angle and jet throat area as geometric parameters. The variation of jet convergence angle from 15 to 40 deg had little effect on the performance of the nozzles having the large value of primary throat area; however, increasing jet convergence angle generally had an adverse effect on performance of the nozzles having the smaller value of primary throat area. The performance of the nozzle configurations with the larger primary throat area is competitive with nozzles designed for operation over the Mach number range.

Mercer, C. E.↗
NASA NTRS1972

Effects of an in-flight thrust reverser on the stability and control characteristics of a single-engine fighter airplane model

The changes in thrust minus drag performance as well as longitudinal and directional stability and control characteristics of a single-engine jet aircraft attributable to an in-flight thrust reverser of the blocker-deflector door type were investigated in a 16-foot transonic wind tunnel. The longitudinal and directional stability data are presented. Test conditions simulated landing approach conditions as well as high speed maneuvering such as may be required for combat or steep descent from high altitude.

Mercer, C. E.↗