Search NASA⌕ Search

Engineering topics

Messner, Mark C.

Publications and source records attributed to Messner, Mark C..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Robust Solar Receivers Using MAX Phase Materials

This work was supported by the U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy under the Solar Energy Technologies Office Award Number 35928. The objective of the proposed effort was to develop and optimize additive manufacturing technologies for low-cost fabrication of high-temperature receivers using MAX phase-based materials (Ti 3 SiC 2 and Ti 3 AlC 2 ). MAX phase materials are a group of ternary metal carbides and nitrides where M stands for an early transition metal element, A is a group 13–16 element, and X is C and/or N. In Phase 1, the binder jetting additive manufacturing process was used to synthesize and characterize the Ti 3 SiC 2 MAX phase material. The typical process involved first producing a TiC preform using binder jetting followed by infiltration of the preform with silicon melt to form Ti 3 SiC 2 in situ. The reaction-infiltrated samples showed formation of MAX phase in the sample core; however, the surface showed cracking. Various process conditions—cooling rates, hold times, Si proportion, etc.—were varied to minimize the surface cracking. The fabricated MAX phase core was characterized by microstructure analysis and evaluations of mechanical properties such as hardness and thermal shock. In Phase 2, the focus included fabrication of Ti 3 SiC 2 MAX phase materials by spark plasma sintering (SPS) and synthesis of Ti 3 AlC 2 MAX phase materials by the Al melt infiltration process. It is expected that Al infiltration will not cause sample cracking, since Al does not expand during solidification. In addition, other processing approaches were investigated to fabricate the MAX phase materials, such as SPS with a graphite bedding approach for producing short-length Ti 3 AlC 2 MAX phase tubes for demonstration of prototypical Concentrating Solar Power receiver tubes. Fabricated samples underwent thermo-mechanical testing to validate the materials for the solar receiver application at temperatures >1000°C. In Phase 3, the effort focused on the development and optimization of the Ti-Al-C MAX phase composite material using the Al melt infiltration approach. We started with optimization of precursor powders and making preform structures by either pressing them in a die or using the binder jetting additive manufacturing process followed by Al melt infiltration. In addition, we investigated the formation of preform structures by cold isostatic pressing followed by Al melt infiltration for making Ti-Al-C MAX phase composite. Thermo-mechanical characterizations, such as creep, strength, and thermal shock, were conducted to establish the structures’ performance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Initial Alloy 709 constitutive models for use with the ASME design by inelastic analysis and EPP+SMT design methods

This report details a preliminary inelastic constitutive model describing the behavior of Alloy 709. This model will serve two purposes: (1) integration into Nonmandatory Appendix HBB-Z of the ASME Boiler & Pressure Vessel Code Section III, Division 5 and (2) extrapolating cyclic test data to difficult to measure conditions for formulating improved creep-fatigue design methods. For both applications, the model must accurately capture the material behavior across a wide range of temperatures and a variety of test conditions, both monotonic and cyclic. For this purpose we adopt a universal model form under consideration to standardize the description of high temperature constitutive models in the ASME Code. This report briefly restates that model form and how we calibrate the model against the test data, summarizes the test database, and validates the final, trained model by comparison to the experimental tests.

36 MATERIALS SCIENCE↗
DOE OSTI2024

NEML2: A High Performance Library for Constitutive Modeling

NEML2, the New Engineering Material model Library, version 2, is an offshoot of NEML, an earlier material modeling code developed at Argonne National Laboratory. NEML2 extends the key philosophy of its predecessor, i.e., material models are flexible, modular, and can be built from smaller blocks. It also provides modern features that do not exist in the framework of its predecessor such as material model vectorization, automatic differentiation, device-portable just-in-time compilation, operator fusion, lazy tensor evaluation, etc. Moreover, NEML2 can seamlessly integrate with the popular machine learning package PyTorch to take advantage of modern and fast-growing machine learning techniques. In this fiscal year, the development of core library features and capabilities are complete. The purpose of this report is not to serve as a verbatim copy of the software API reference (which is available online at https://reverendbedford.github.io/neml2/). Instead, this report documents the motivation, implementation, design choices, and usage of each core capability as well as their applications in solving practical engineering problems. This report is compiled based on the NEML2 major release 2.0.0.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Simplified inelastic constitutive models for ASME Section III, Division 5 design by inelastic analysis

This report describes the development of simplified, universal constitutive model that captures the high temperature monotonic and cyclic behavior of a range of commonly-used high temperature materials. The goal of the work is to provide a simple, universal constitutive model to replace the current bespoke models for Grade 91, 316H, and Alloy 617 included in Nonmandatory Appendix HBB-Z of the ASME Boiler & Pressure Vessel Code, and to extend this model to cover Alloy 800H. We initiated this work in response to feedback from reactor vendors and other Code users requesting simplified models, compared to the current models, that are easier to implement and use in commercial finite element analysis software. This report describes the completion of this effort by developing a model to correct the defects in standard model forms presently used for high temperature material modeling, described in past work, developing and implementing new numerical methods to train this model against test data, and then actually training the model for the four materials. The report provides a complete mathematical description of the model along with the tabulated material coefficients for the four materials. The final step will be to formulate an ASME Code change to introduce the new models into the Code.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Simulating the effect of grain structure and porosity on creep for powder bed fusion 316H

This report details results from modeling studies focused on identifying the potential factors influencing creep performance of 316H stainless steel manufactured using Laser Powder Bed Fusion (LPBF), with a focus on experimentally-observed and predicted differences between the response of the AM material and conventionally manufactured wrought 316H. The studies presented here systematically look at the role of grain structure, porosity and texture in the anisotropic creep behavior of the material under conditions expected in high temperature advanced nuclear reactors. A physics-based Crystal Plasticity Finite Element modeling approach has allowed us to look at these factors in isolation and study their role in the material's long-term deformation behavior. An update to the precipitation model used in the constitutive framework for 316H is also presented here, with the aim of improving the accuracy of our results from this modeling effort. This work is a step in the direction of gaining mechanistic understanding of the long-term deformation behavior of LPBF 316H, helping us model its long term performance and reducing the qualification time for the material.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Updated ASME design correlations and qualification plan for powder bed fusion 316H stainless steel

This report provides an update on the Advanced Materials and Manufacturing Technologies (AMMT) program effort to qualify Laser-Powder Bed Fusion (L-PBF) 316H stainless steel for use with the ASME Boiler & Pressure Vessel Code Section III, Division 5 rules. The report summarizes progress in testing and characterizing L-PBF material at elevated temperatures by providing preliminary design data for L-PBF 316H and by comparing the elevated temperature performance of the L-PBF material to wrought and conventional fusion welded 316H. The report then updates the initial AMMT qualification plan for L-PBF 316H, originally developed in 2023, to update the accelerated qualification strategy adopted in that plan to account for the new high temperature test data. The report also explores a few methods for further accelerating the qualification process using machine learning techniques to supplement the more conventional, empirical analysis methods typically used by ASME to correlate and extrapolate time-dependent material test data.

36 MATERIALS SCIENCE↗
DOE OSTI2024

ASME Section III, Division 5, Class A 100,000-hour design data for Alloy 709

This report documents the 100,000 hour, Class A ASME design material data for Alloy 709 based on the extensive Department of Energy, Office of Nuclear Energy, Advanced Reactor Technologies qualification test campaign. This report includes design tensile properties, creep rupture data, allowable stresses, isochronous stress-strain curves, buckling charts, and a few additional miscellaneous pieces of design data. Companion work at Oak Ridge National Laboratory and Argonne National Laboratory provide design cyclic data --- fatigue charts and creep-fatigue diagrams --- and an inelastic constitutive model. This work substantially completes the ASME data package for the Alloy 709 Code Case, though the design data will continue to updated as the final tests finish. This report also compares the design performance of Alloy 709 against that of 316H stainless steel to provide a reference for the improved high temperature strength of 709 compared to a reference material for sodium fast reactor construction.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Acceptance criteria for in situ surveillance of MSR materials based on thermally-loaded mechanical test articles

This report describes practices and acceptance test procedures for designing, running, and maintaining a material surveillance program in a future operating molten salt reactor. The programs described here rely on test data from passively actuated mechanical test articles inserted into critical regions of the reactor and periodically removed for out-of-reactor testing. The report defines definite acceptance procedures, based on the results of these tests, to determine whether a component can continue to operate accounting for the accumulation of environmentally-assisted mechanical damage in the component materials to date, and extrapolated out through the next inspection period. Additionally, the report describes work on a software tool implementing many of the surveillance methods and procedures described here and progress on simplified methods for inferring damage accumulation in the test articles, based on out-of-reactor thermal cycling, that do not rely on sophisticated numerical analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Design Methods, Tools, and Data for Ceramic Solar Receivers

This report presents the development of tools and methods for evaluating the reliability and performance of ceramic materials in high temperature solar receivers. As Concentrating Solar Power (CSP) technologies aim for higher operating temperatures to enhance efficiency and meet industrial process heat requirements, current high temperature metallic materials face challenges in maintaining structural integrity. This report explores advanced ceramics as a promising alternative, given their superior high temperature strength and lower thermal expansion, compared to metals. To address the need for effective ceramic receiver design tools, this report integrates statistical failure models of ceramics into the existing srlife tool: an open-source software package designed to estimate the life of high temperature CSP components. These failure models account for the inherent variability and flaw distribution in ceramics, as well as the impact of subcritical crack growth under high temperature cyclic loads. The report also presents experimental data collected for a commercially available ceramic material, SiC, and details the process of estimating reliability model parameters from these data. A comparative design analysis is then performed between ceramic (SiC) and metallic (current nickel-based superalloys A740H and A282) receiver. This comparison demonstrates that SiC receivers can achieve service life exceeding 30 years under high incident heat flux conditions, compared to just a few years for metallic receivers.

14 SOLAR ENERGY↗
DOE OSTI2024

Reliability comparisons between additively manufactured and conventional SiC–Si ceramic composites

Abstract An additively manufactured reaction‐bonded silicon carbide ceramic composite is fabricated using a bimodal powder feedstock and the binder‐jetting printing technique. On fabricating, the ceramic is investigated to report its composition, mechanical, and thermal properties at room temperature and high temperatures (up to 750). The ceramic has a density of 2.76 g/cc, and shows a hardness of 21.74 GPa, and a flexure strength of 207.5 MPa at room temperature. The mechanical property of flexure strength is used to estimate its failure probability under applied stress, using a Weibull distribution. The mechanical properties and failure probabilities are compared with those of conventionally fabricated reaction‐bonded silicon carbide ceramics reported in the literature. These ceramics were fabricated using methods such as slip‐casting, compacting, and tape‐casting. The comparison is used to elucidate the advantages and areas of improvement of the present additive manufacturing technique for reaction‐bonded ceramics.

14 SOLAR ENERGY↗
DOE OSTI2023

A Three-Dimensional, Thermodynamically and Variationally Consistent, Fully Coupled, Electro-Chemo-Thermo-Mechanical Model of Solid-State Batteries

Here we present a theoretical framework for high fidelity modeling of three-dimensional electro-chemo-thermo-mechanical coupled systems such as solid-state batteries. The framework provides a useful means of utilizing molecular level information to predict the overall performance of the system at the continuum level. The central statement of the theoretical framework is a thermodynamically consistent inf-sup problem. The total potential of the coupled system consists of the Helmholtz free energy, the electrical kinetic potential, the chemical potential, the Fourier potential, the chemical reaction potential, and the external power expenditure. All governing equations derive from variational principles. We also show that the resulting initial-boundary-value problem (IBVP) is consistent with existing, widely adopted equations for modeling batteries. Moreover, the IBVP can be naturally discretized using the (variational) finite element method to simulate practical solid-state batteries with arbitrary geometries. Several examples illustrate multiphysics coupling between pairs of the physical field equations, culminating in a comprehensive three-dimensional model of charge-discharge in a solid state battery.

25 ENERGY STORAGE↗
DOE OSTI2023

A mechanistic model for creep and thermal aging in Alloy 709

This report describes a physics-based model for creep and thermal aging in Alloy 709. Alloy 709 is an advanced austenitic alloy, targeted for use in future Sodium Fast Reactors (SFRs) and other advanced reactors. The material has superior high temperature properties compared to currently qualified 316 and 304 stainless steels. However, the available creep and thermal aging test database for Alloy 709 is significantly more limited compared to the historical materials. The physics-based model developed here is one way to accelerate the qualification of the material by providing more accurate long-term predictions for creep properties and thermal aging, compared to current empirical time-extrapolate techniques. The crystal plasticity finite element model is used to predict the deformation and failure of alloy 709. The same setup for the CPFE model is used in both the baseline model calibration process and the simulation campaigns for parameter inference. Specific constitutive choices are made for Alloy 709 to capture the primary deformation mechanisms. The dislocation creep formulation developed by Hu and Cocks is extended to account for coupled precipitation formation and the grain boundary cavitation model developed by Sham, Needleman, et al. is used to model grain boundary cavitation-induced failure. A novel update algorithm is proposed to render the semi-discrete constitutive update for the Sham-Needleman model unconditionally stable. A progressive calibration approach is adopted based on the observations that several types of material responses can be effectively decoupled. A surrogate model is trained based on full-fledged CPFE simulations to accelerate the forward model evaluations, and stochastic variational inference (SVI) is used to calibrate the unknown microstructural model parameters. The calibrated mechanistic model is used to predict the long-term creep life of Alloy 709, and the predictions are compared against classical empirical approaches.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Modeling support for the development of material surveillance specimens and procedures

This report describes modeling and simulation activities performed at Argonne National Laboratory supporting the development of passively actuated mechanical test articles for material surveillance in Molten Salt Reactors (MSRs). These test articles are a critical technology in formulating material surveillance programs for future MSRs to monitor the degradation in the structural properties of the materials in critical plant components. The main activity described in this report is the development of a method for inferring the amount of mechanical damage a test article has experienced during some duration of exposure to plant thermal and environmental conditions, using only mechanical test data collected from the test articles before and after exposure. The basic approach is to develop a model of the test article, including a description of mechanical degradation through continuum damage mechanics, and then use this model to cast the problem of inferring mechanical degradation in the test article materials into a shooting problem for a set of ordinary differential equations. We can then solve the shooting problem to determine the amount of damage accumulated in the sample. The report also details a few miscellaneous simulation studies completed at Argonne to support the development of the test articles themselves at Idaho National Laboratory.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

Preliminary prediction of long-term aging and creep behavior of AM 316 SS

This report describes the development of initial mechanism models for the long term behavior of additively manufactured (AM), laser powder-bed fusion 316H stainless steel under the conditions expected in future advanced nuclear reactors. These models focus on key features of the material microstructure and response that differ from the conventionally-manufactured wrought material. Specifically, the report describes the development of models to capture the unique response of the AM material focusing on irradiation creep and swelling, the effect of internal stress, for example caused by dislocation structure, on precipitation, and the effect of the AM grain and dislocation structure on the macroscale creep and thermal aging behavior. This single mechanism models represent progress towards a complete, physics-based model for the long-term material behavior as well as elucidate key differences in the AM material behavior, when compared to the better-understood, conventionally-manufactured 316H.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High temperature inelastic constitutive models for the ASME Section III, Division 5 Class A materials

This report describes the exploration of a universal high temperature inelastic constitutive model for use with the ASME Boiler & Pressure Vessel Code Section III, Division 5, Class A design rules. The idea, developed based on feedback from reactor vendors, is to simplify the current bespoke material models for Grade 91, 316H, and Alloy 617 and the new model for Alloy 800H into a simple, single model form. The report describes a new parallel time integration technique implemented in the pyoptmat package which allowed us to explore a wide variety of model forms, searching for a suitable common model. The report then describes preliminary work on models for monontonic deformation and then the development of a set of models suitable for capturing high temperature cyclic deformation. These models are suitable for use with the ASME design rules, except potentially for a narrow, material-specific band of temperatures at the edge of the creep regime. An incremental improvement the current models could overcome this discrepancy and provide a new, simpler set of constitutive model for all four materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High Temperature Ceramic Heat Exchangers for the Gen3 Concentrated Solar Power Systems

As part of the Department of Energy’s Solar Energy Technology Office (SETO), the Concentrated Solar Power (CSP) Gen3 Demonstration Roadmap outlined the various technology pathways, goals, and technology needs/gaps to integrate CSP to a supercritical CO 2 (sCO 2 ) power cycle that operates at temperatures >700 °C. It is envisioned that the higher temperature power cycle will enhance the overall system efficiencies and reduce the levelized cost of electricity (LCOE) to meet a 2030 cost target of $0.05/kWhe for baseload CSP plants with ≥12 hours of storage. In this regard, there is a need for heat exchangers (HXs) that can operate at high sCO 2 pressures and temperatures >700 °C. Since current high-temperature alloys degrade at high temperatures, as part of this project, advanced ceramic materials, HX designs, and low-cost additive manufacturing approaches were developed to fabricate and evaluate the performance of the lab-scale ceramic HX prototypes.

14 SOLAR ENERGY↗
DOE OSTI2023

An ICME Modeling Framework for Metal Matrix Composites Focusing on Ultrahigh Temperature Matrix Material and Tungsten Carbide Reinforcement Particulate (Final CRADA Report)

Ultra High Temperature Metal Matrix Composites (UHT-MMCs) are of interest to the due to their potential defense and aerospace applications. These materials consist of a metal matrix reinforced with a stiff ceramic or cermet. Based on a preliminary literature survey, this project will focused on a pure titanium (Ti) matrix reinforced with tungsten carbide-cobalt (WC-Co). UHT-MMC technology is still at a nascent stage of development and requires extensive experimental work to optimize the structure and resulting material properties of a particular UHT-MMC material system. An accurate and complete high-performance computing (HPC) model of the Ti/WC-Co material system could greatly accelerate the development and deployment Ti/WC-Co materials by connecting processing parameters to material properties. This type of model could then be used in an integrated computational materials engineering approach to optimize the material structure to achieve a targeted level of performance.

36 MATERIALS SCIENCE↗