Search NASA⌕ Search

Engineering topics

Messner, Mark C.

Publications and source records attributed to Messner, Mark C..

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

A method for predicting failure statistics for steady state elevated temperature structural components

This paper presents the initial development of a high temperature life prediction method that accounts for the variability in the material properties of Grade 91 steel. The method accounts for material variability by fitting a variable 3-parameter Weibull distribution to experimental rupture data and accounts for the variability of creep deformation on the steady-state stresses via a Monte Carlo approach. To ensure reasonable computational times, the model represents the material as an extremely viscous Stokes fluid with a non-Newtonian viscosity, therefore solving the stress relaxation problem with a steady, static, instead of transient, analysis. Furthermore, the complete statistical analysis combines this model for creep deformation with a probabilistic model for creep rupture to evaluate the probability of premature failure for a set of sample problems, comparing the predicted failure statistics to the design life predicted by the ASME Boiler and Pressure Vessel Code rules.

42 ENGINEERING↗
DOE OSTI2021

A Minimum Creep Rate for 2-1/4Cr-1Mo Steel Consistent With the ASME Section III, Division 5 Rules

This technical note describes a minimum creep rate model for 2-1/4Cr-1Mo steel that is consistent with the current creep strain equation embedded in the ASME Boiler & Pressure Vessel Code Section III, Division 5, Subsection HB, Subpart B isochronous stress–strain curves. Minimum creep rate models for all the Section III, Division 5 Class A materials are required for the development of improved high temperature design methods. Of all the Class A materials, only 2-1/4Cr-1Mo does not have a readily identifying minimum creep rate term in the current isochronous stress–strain curve model.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Survey of Modeling and Simulation Techniques for Advanced Manufacturing Technologies Volume II – Predicting Material Performance from Material Microstructure

This report describes the current state of modeling and simulation techniques for predicting the properties of materials fabricated with advanced manufacturing techniques, given the initial microstructure of the material. The report includes a literature survey and a gap analysis outlining and prioritizing key issues in applying these modeling and simulation techniques to nuclear reactor structural materials. The discussion covers both physics-based and data-driven modeling techniques and includes a broad range of manufacturing techniques and materials that may have future nuclear applications. This report is the second in a two-part series, with the first report covering modeling and simulation methods for predicting the initial, as-manufactured structure of advanced manufacturing materials, given a description of the process. Both reports focus on a set of manufacturing technologies likely to be applied to reactor structural components. Taken together, the two reports provide a complete summary of the current state of processing-structure-properties models for advanced manufacturing as well as a survey of applications to reactor structural materials

42 ENGINEERING↗
DOE OSTI2020

Survey of Modeling and Simulation Techniques for Advanced Manufacturing Technologies Volume I – Predicting Initial Microstructures

This report summarizes the current state of modeling and simulation methods for predicting the initial structure and properties of material in components assembled using advanced manufacturing technologies (AMTs). The report is the first volume in a two-volume series. This first volume focuses on predicting initial microstructures of AM material. The second volume discusses predicting material properties given the initial microstructure. The focus is on technologies of particular relevance to the design and manufacture of nuclear reactor components. The purpose of the report is to help develop the technical knowledge base to support regulatory decisions that will be needed to assess nuclear components manufactured with AMTs as these components are installed at nuclear power plants (NPPs). The report develops a list of AMTs of particular interest to the NRC and summarizes the key microstructural features and corresponding processing parameters relevant to each technology. Further sections describe available physically-based and data-driven prediction methods and survey widely available software tools. The report concludes with a summary of gaps that may be of particular interest to the NRC when evaluating modeling and simulation methods for AMTs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Example Evaluation of a Representative Heat Pipe Test Article Design for Structural Acceptability using ASME Design Rules

This report describes a design analysis of a test article mimicking a core block of a heat-pipe mi-croreactor using the ASME Boiler & Pressure Vessel Code Section III, Division 5, Subsection HB, Subpart B rules. These rules cover the design and construction of elevated temperature nu-clear reactor structural components, like the core block of a heat-pipe microreactor emulated by the test article. The purposes of the report are to: (1) provide a step-by-step example of applying the ASME rules to a reasonable core block geometry and corresponding loading conditions, (2) to provide design feedback on the test article, and (3) to evaluate the ASME rules for use in the design of complex heat-pipe microreactor components. The test article design has a relatively short ASME design life, limited by high thermal stresses. The current ASME rules are adequate for evaluating the core block component designs, though they could be optimized to increase the design efficiency and reduce the amount of designer/analyst time required to execute the design process. The report covers both the current, 2019 edition ASME rules and modified, currently unapproved, rules designed to improve the design process for components with complex geometries and high secondary stresses, like the core block test article.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Initial development of a high temperature life prediction method directly accounting for variability in material properties

This report presents the initial development of a life prediction method that accounts for the variability of the material properties in Grade 91 steel. We account for material variability by both fitting a variable 3-parameter Weibull distribution to the rupture data of the material and by quantifying the effect that the creep deformation properties have on stresses via a Monte Carlo approach. To ensure a reasonable time frame when applying Monte Carlo to the creep stress, we propose a methodology that models the material as an extremely viscous Stokes flow with a non-Newtonian viscosity, therefore solving the problem in a single step. We use the final probabilistic model for structural failure developed in this document to evaluate a Flat Head Vessel designed with the Section III, Division 5 ASME Boiler Pressure and Vessel Code rules with a 100,000h design life and assess its probability of premature failure.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Sample problems for Section III, Division 5 design by inelastic analysis of Grade 91 components

This report works through two sample design analyses of representative Grade 91 components using the ASME Boiler & Pressure Vessel Code Section III, Division 5, Appendix HBB-T rules for the strain and deformation and creep-fatigue design criteria using a design by inelastic analysis approach. The component geometries and loadings were selected to span a wide variety of potential applications. The sample components are an endplate geometry, which is fairly representative of typical pressure vessel construction, and a core block, representing a critical component in a heat pipe microreactor, which has a complicated geometry and complex thermal stress history. These sample problems serve several functions. First, they are complete worked examples of how to apply the current design by inelastic analysis rules. Second, they serve as test cases to evaluate the current rules and provide feedback on how they could be optimized to deal with complicated component geometries or to be better automated in modern finite element analysis software. Finally, the analysis here uses an inelastic constitutive model for Grade 91 developed by Argonne National Laboratory and proposed for inclusion in the ASME Boiler & Pressure Vessel Code Section III, Division 5 rules as a reference constitutive model. Using this constitutive model in the sample problem analyses tests the model in the context of the ASME Code rules. The final conclusions of this report are that the material model and the current Code rules are satisfactory, but that the Code rules could be optimized to simplify automation and reduce over conservatism. Future work should address the specific optimization topics discussed in this report.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Initial development of an in-situ, passive material surveillance test article for monitoring high temperature reactor structural components

This report describes the development of a family of passively-actuated surveillance test articles, suitable for use in an in-situ reactor test program monitoring the degradation in structural material properties caused by the reactor environment. The test articles apply creep-fatigue-type cyclic load to a test section driven by changes in the reactor coolant temperature converted to mechanical force by differential thermal expansion. The report describes three types of test articles, all of which apply the load to a 316H test section using Alloy 617 as the driver material. The three types of specimens each serve a unique purpose: (1) initial proof-of-concept, (2) validation of the models used to size the specimens to achieve a given strain range, and (3) demonstration that the articles can be miniaturized for use in an actual operating reactor. In addition to the specimen design, fabrication, and testing, this report describes the outline of two types of in-situ monitoring programs, using the test article. Monitoring programs such as these could be a critical component in gaining regulator acceptance for Molten Salt Reactor (MSR) designs using structural materials for which there is little long-term experimental environmental testing or operating experience available for calibrating the component structural design.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Preliminary design analysis workflow for Division 5 HHA-3200 requirements for graphite core components

This report presents a design analysis workflow for graphite core components and assemblies, based on the design rules of ASME Boiler Pressure and Vessel Code, Section III, Division 5, Article HHA-3000. The workflow contains three stages: developing the design of the graphite core component, modeling the component with the finite element software MOOSE, and assessing if the component passes/fails the criteria of the HHA-3000 design rules. Since the design rules use probabilistic metrics specifically established to evaluate brittle materials, we developed a python library that performs all the statistical calculations necessary for the evaluations of the HHA-3000 criteria.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

One piece ceramic heat exchanger for concentrating solar power electric plants

Using additive manufacturing techniques, a ceramic heat exchanger was optimized for a concentrating solar power (CSP) electric power plant with a corrosive molten salt at atmospheric pressure as the solar field heat transfer fluid and supercritical carbon dioxide at 200 bar as the power block fluid. Temperatures ranged from 750 °C to 540 °C. The plant heat exchanger was optimized for heat transfer and stress using 1 m³ modules arranged in parallel. Heat transfer was optimized using COMSOL Multiphysics software resulting in a unique semi-elliptical cross section for the fluid flow channels in a counter-flow configuration. Counter-flow was made possible through additive manufacturing of the fluid headers as part of each modular heat exchanger thus producing the entire module as a single piece and minimizing cost. Using reasonable parametric values, a heat exchanger module was optimized to 0.5 MW/m³, and a section of it was manufactured including the fluid headers. Here, parametric studies showed the potential for a module to reach 3.5 MW/m³.

14 SOLAR ENERGY↗
DOE OSTI2020

Initial development and verification of a primary load design method based on elastic-perfectly plastic analysis

This report describes a new primary load design method to supplement the current design-by-elastic-analysis rules in Section III, Division 5, Subsection HB, Subpart B of the ASME Boiler and Pressure Vessel Code, covering the design and construction of Class A high temperature nuclear structural components. The main objectives for the new design method are to provide a procedure that can be applied to components with complicated geometries and to simplify the primary load design process by providing rules more compatible with modern finite element analysis. The report includes a complete set of design rules, presented as a draft ASME Code Case, as well as a commentary on the rules and a set of verification problems. The verification design problems demonstrate the new primary load design rules produce safe, efficient components when compared to the current Division 5 approach, while greatly simplifying the design analysis process.

42 ENGINEERING↗
DOE OSTI2020

Design Guidance for High Temperature Concentrating Solar Power Components

This report provides guidance for the design of components for concentrating power facilities operating at high temperatures and undergoing high, secondary thermal stresses relative to the applied primary pressure stress. The design rules were developed for the design of Generation 3 CSP tubular receivers manufactured from Alloy 740H, but are generally applicable to a wide range of component types undergoing similar loads. Part 1 of the report provides procedural design rules for components to be used in conjunction with the 2019 edition of the ASME Boiler & Pressure Vessel Code. Part 2 provides corresponding design data for Alloy 740H. Part 3 of the report is a commentary describing the rationale behind the design rules and the data underlying the design material properties. Finally, Part 4 provides an extensive set of worked sample problems detailing the application of the rules to CSP components.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2019

Convolutional Neural Network Surrogate Models for the Mechanical Properties of Periodic Structures

The work in this paper describes neural network surrogate models for calculating the effective mechanical properties of a periodic composites. The models achieve good accuracy even when only provided with training data sampling a small portion of the design space. As an example, the surrogate models are applied to solving the inverse design problem of finding structures with optimal mechanical properties. The surrogate models are sufficiently accurate to recover optimal solutions in general agreement with established topology optimization methods. However, improvements will be required to develop robust, efficient neural network-based surrogate models and several directions for future research are highlighted here.

42 ENGINEERING↗
DOE OSTI2019

Report on FY19 Testing in Support of Grade 91 Core Block Code Case

This report summarizes the experimental results performed in FY 2019 on grade 91 (Gr. 91) steel (heat 30176) in support of Gr. 91 core block code cases. Mean stress fatigue testing was completed, and the evaluation led to the conclusion that mean stress correction on the fatigue curve in Division 5 for Gr. 91 is not recommended. A specialized test was designed and performed to validate the methodology proposed for a softening factor to support the extension of the elastic—perfectly plastic (EPP) strain limits design rules to Gr. 91. Nine simplified model tests (SMTs) were completed using the newly developed two-bar SMT (TBSMT) and single-bar SMT (SBSMT) techniques. The results demonstrate the validity of the testing technique, and the experimental basis of the development of the integrated EPP plus SMT creepfatigue evaluation methodology.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Report on FY19 Testing in Support of Integrated EPP-SMT Design Methods Development

Experiments in support of the development of the integrated Elastic–Perfectly Plastic (EPP) analysis and Simplified Model Test (SMT) design methodology continued in FY 2019. Major progress was made in the verification of the newly developed two-bar SMT and single-bar SMT (SBSMT) methods by performing tests on Alloy 617 and SS 316H at high temperatures. Comparable results were achieved when the materials were tested under same conditions using both techniques. Because of its simple test configuration, SBSMT was the preferred testing technique used to evaluate elastic follow-up effect and generate data in support of SMT-based design curves. Evaluation of elastic follow-up was started with testing SS 316H at 815°C using SBSMT in this reporting period. As a result of this effort, the basic procedure and test protocol to provide data in support of the development of SMT-based design curves were established. This report also summarizes recent test results for the pressurization SMT using test articles with key features on Alloy 617 at intermediate strain ranges and at a low temperature of 850°C. Although more test results are needed in order to fully understand the effect of primary load on SMT creep-fatigue (CF) life, the limited test data indicate that the primary load reduced the SMT life at intermediate strain ranges and high temperatures. Recognizing the advantages of the newly developed SBSMT method, a new test geometry was designed to allow the elevation of the primary load effect on SMT CF life with the SBSMT technique. Additionally, selected tests were performed on SS 316H (heat 101076) to provide basic information about the heat of material. The tests performed included high-temperature tensile, fatigue, creep fatigue, and thermomechanical experiments. The results will be used to support the verification of the material constitutive model developed at Argonne National Laboratory.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Development of Simplified Model Test Methods for Creep-Fatigue Evaluation

The Simplified Model Test (SMT) approach is an alternative creep-fatigue evaluation method that no longer requires the use of the damage interaction diagram, or D-diagram. The reason is that the combined effects of creep and fatigue are accounted for in the test data by means of a SMT specimen that is designed to replicate or bound the stress and strain redistribution that occurs in actual components when loaded in the creep regime. However, creep-fatigue experiments on SMT key feature articles are specialized and difficult to perform by the general research community. In this paper, two innovative SMT based creep-fatigue experimental methods are developed and implemented. These newly-developed SMT test methods have resolved all the critical challenges in the SMT key feature article testing and enable the potential of further development of the SMT based creep-fatigue evaluation method into a standard testing method. Scoping test results on Alloy 617 and SS 316H using the newly developed SMT methods are summarized and discussed. The concepts of the SMT methodology for creep-fatigue evaluation are explained.

Wang, Yanli↗