Search NASA⌕ Search

Engineering topics

Metzger, Wyatt K.

Publications and source records attributed to Metzger, Wyatt K..

17 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Quantitative assessment of selenium diffusion and passivation in CdSeTe solar cells probed by spatially resolved cathodoluminescence

The introduction of selenium in CdSeTe/CdTe solar cells has led to improved device performances attributed to the passivation of bulk defects. In this work, high-resolution cathodoluminescence experiments are performed on a series of CdSeTe/CdTe thin films with different Se concentrations to quantify the mechanisms and the passivation role of Se. We demonstrate a universal dependence between the Se concentration and the radiative efficiency and a ten-fold enhancement of the luminescence between CdTe and CdSe 0.4 Te 0.6 . Raw luminescence maps are converted into maps of the Se concentration, revealing its graded profile within the stack. We demonstrate the diffusion of Se along CdTe grain boundaries induced by the cadmium chloride annealing treatment and determine the diffusion coefficients, which are more than eight times higher at grain boundaries than in grain interiors. These results provide microscopic insights into the distribution of Se and its impact on the passivation of CdSeTe/CdTe solar cells.

14 SOLAR ENERGY↗
DOE OSTI2023

CdTe-based thin film photovoltaics: Recent advances, current challenges and future prospects

Cadmium telluride (CdTe)-based cells have emerged as the leading commercialized thin film photovoltaic technology and has intrinsically better temperature coefficients, energy yield, and degradation rates than Si technologies. More than 30 GW peak (GWp) of CdTe-based modules are installed worldwide, multiple companies are in production, modules are shipping at up to 18.6% efficiency, and lab cell efficiency is above 22%. We review developments in the science and technology that have occurred over approximately the past decade. These achievements were enabled by manufacturing innovations and scaling module production, as well as maximizing photocurrent through window layer optimization and alloyed CdSe x Te 1-x (CST) absorbers. Improved chlorine passivation processes, film microstructure, and serendipitous Se defect passivation significantly increased minority carrier lifetime. Efficiencies >22% have been realized for both Cu and As doped CST-based cells. The path to further efficiency gains hinges primarily on increasing open circuit voltage (V oc ) and fill factor (FF) through innovations in materials, fabrication methods, and device stacks. Replacing the longstanding Cu doping with As doping is resulting in better module stability and is being translated to large-scale production. To realize 25% efficiency and >1 V V oc , research and development is needed to increase the minority carrier lifetime beyond 100 ns, reduce grain boundary and interface recombination, and tailor band diagrams at the front and back interfaces. Many of these goals have been realized separately however combining them together using scalable manufacturing approaches has been elusive to date. We review these achievements and outstanding opportunities for this remarkable photovoltaic technology.

14 SOLAR ENERGY↗
DOE OSTI2022

Codesigning Alloy Compositions of CdSe y Te 1− y Absorbers and Mg x Zn 1− x O Contacts to Increase Solar Cell Efficiency

Thin‐film solar cells such as CdTe are a major commercial photovoltaic technology, with more than 25 GW installed worldwide and levelized costs of electricity competitive with fossil fuels. Further progress may result from integrating CdSe y Te 1− y absorbers with Mg x Zn 1− x O contacts, but the device efficiency is difficult to maximize due to coupled dependence on chemical composition of both alloys. Herein, a high‐throughput approach is demonstrated to codesign chemical compositions in alloyed Mg x Zn 1− x O/CdSe y Te 1− y thin‐film solar cells, using combinatorial libraries of PV devices with orthogonal composition gradients in CdSe y Te 1− y absorbers and Mg x Zn 1− x O contacts. It is found that the solar cell performance is a strong and coupled function of both elemental compositions, with efficiency up to 17.7% ( V OC = 836 mV, fill factor = 69%, J SC = 30.6 mA cm −2 ) at atomic compositions of Mg/(Mg + Zn) ≈18% and average Se/(Se + Te) ≈4%. These performance trends among >100 devices are explained by >100 ns lifetime of photoexcited charge carriers at the Mg x Zn 1− x O/CdSe y Te 1− y interface where strong Se accumulation is also observed. This study reports the optimal compositions of the commercially relevant Mg x Zn 1− x O/CdSe y Te 1− y solar cells and demonstrates a general approach to codesigning performance of alloyed thin‐film solar cells and other optoelectronic devices.

14 SOLAR ENERGY↗
DOE OSTI2021

Imaging CdCl 2 defect passivation and formation in polycrystalline CdTe films by cathodoluminescence

Polycrystalline thin-film solar cells are attractive for low-cost photovoltaics, but their efficiencies are hindered by material quality issues. State-of-the-art CdTe solar cells use CdCl 2 annealing treatments whose effects are still being discovered at a fundamental level. Here, a series of CdTe samples with different annealing temperatures is investigated with high-resolution hyperspectral cathodoluminescence mapping measured at both room temperature and low temperature on the same microscopic areas. A statistical analysis over a large number of grains is combined with a local analysis at grain boundaries. The results elucidate the dynamic interplay between grain boundary and intragrain defect passivation and formation, in the midst of grain growth. The CdCl 2 annealing initially contributes to an increase of the grain size and the passivation of both grain boundaries and grain interiors, increasing the overall luminescence and diffusion length. For higher annealing temperatures, a further increase of grain size is counterbalanced by the rise of bulk defects. The results illustrate the tradeoffs that lead to an optimal annealing temperature, as well as new methods for understanding defect passivation and creation in thin film solar cells.

14 SOLAR ENERGY↗
DOE OSTI2021

Exceeding 200 ns Lifetimes in Polycrystalline CdTe Solar Cells

CdTe photovoltaics has achieved one of the lowest levelized costs of electricity among all energy sources. However, for decades, carrier lifetimes have been inferior to those of other prevalent solar cell materials. This quality has inhibited common methods to improve solar cell efficiency such as back-surface fields, electron reflectors, or bifacial solar cells. In this work, a significant increase in carrier lifetime to values exceeding 200 ns in fully functional CdTe solar cells is demonstrated. The increased lifetime is achieved by large CdSeTe grains at the absorber/emitter interface, intragrain passivation in the absorber layer, and chemical passivation by forming nanoscale oxidized tellurium species at the transparent conducting oxide interface. The carrier lifetime is correlated to the open-circuit voltage and enables paths for back-surface manipulation and novel cell architectures to further improve CdTe photovoltaic performance.

14 SOLAR ENERGY↗
DOE OSTI2021

Mechanisms for long carrier lifetime in Cd(Se)Te double heterostructures

II–VI semiconductors are used in numerous electro-optical applications. For example, CdTe-based solar technology is cost competitive with other electricity generation sources, yet there is still significant room to improve. Carrier lifetime has historically been well below the radiative recombination limit. Lifetimes reaching beyond 100 ns can significantly enhance performance and enable novel device structures. Here, double heterostructures (DHs) with passivated interfaces demonstrate lifetimes exceeding 1 µs, yet this appears only for CdSeTe and not for CdTe DHs. We compare the passivation mechanisms in CdTe and CdSeTe DHs. CdSeTe lifetimes on the order of 1 µs correspond to a combination of superior intragrain lifetime, extremely low grain boundary recombination and greater Te4+ interfacial presence compared to CdTe.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Colossal grain growth in Cd(Se,Te) thin films and their subsequent use in CdTe epitaxy by close-spaced sublimation

Many technologies deposit thin films on inexpensive substrates, resulting in small grains due to classic nucleation and grain growth theory. For example, state-of-the-art solar cells are made by depositing CdSeTe and CdTe layers on inexpensive glass coated with nanocrystalline transparent conducting oxides (TCOs), like SnO 2 . Characteristically, the grain size of these films is on the order of the film thickness, i.e. a few microns. CdTe small-grain films have poor electro-optical properties and require CdCl 2 passivation which fails to fully passivate grain boundaries, causes carrier compensation, and prevents implementing other II–VI alloys and materials to improve performance. Here, we present a method to increase grain size to 1 mm in CdSe x Te 1-x thin films deposited on glass/TCO substrates without CdCl 2 treatment. The colossal grain growth is driven by mechanisms distinct from classic nucleation, grain growth, and Ostwald ripening and only occurs at low selenium content (x ~ 0.1). We also demonstrate how these films can serve as templates for subsequent large-grain epitaxy of other compositions like CdTe, again without exposure to CdCl 2 . The results open new paths for thin film solar cell technology, and thin film devices in general.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Optimization of Source Material for in-situ Arsenic Doping via Vapor Transport Deposition of CdTe Films

In-situ doping of CdTe/CdSeTe films with arsenic is performed using pre-doped source material prepared by high pressure Bridgman (HPB) melt growth. Arsenic level in the source material is varied from 1018-1020 cm-3. Correspondingly, dopant incorporation in the films prepared using vapor transport deposition (VTD) varied from 3x1017 cm-3–1x1018cm-3. In this range, dopant activation is found to inversely correlate with the dopant incorporation, suggesting compensation. The results from this study indicate film properties can be adjusted by source material.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2020

Se diffusion in CdTe thin films for photovoltaics

Manipulating CdSeTe bandgrading to enhance photocurrent and carrier lifetime is an essential part of high-performance CdTe photovoltaics (PVs). Here, we examine Se diffusion kinetics in single-crystal and polycrystalline CdTe during deposition, thermal annealing, and CdCl 2 treatments. Se distributions are determined by dynamic secondary-ion-mass spectroscopy and Auger electron spectroscopy depth profiling and coupled with electron backscatter diffraction images of the crystalline structure. Effective bulk and grain boundary diffusion coefficients are determined by analytical models and discussed in the context of processing and film morphology. Se is found to diffuse in CdTe at much higher rates during CdCl 2 treatments than with thermal processing alone. GB diffusion also occurs at a significantly faster rate than bulk diffusion. As a result of these two effects, the near interface bulk and GB Se diffusion during CdCl 2 treatments dominates the bandgrading profiles in CdTe PVs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Synthesis of CdSeCdSexTe1-x/CdTe for Graded Solar Cells

Here, we have developed CdSe x Te 1-x /CdTe bilayer deposition for graded solar cell technology. Smoothly graded Se profiles with > 16% efficiency with Jsc=28 m A/cm 2 and 20-ns bulk lifetime has been observed observed. The CdSeTe reveals longer carrier lifetimes than CdTe within the same device.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2020

Spatially and Spectrally Resolved Defects in Polycrystalline CdTe Thin Films Revealed by Quantitative Cathodoluminescence

Increasing the grain size is a potential strategy to reduce grain-boundary recombination and improve performance of thin-film solar cells. Here, CdTe thin films with a range of grain sized were produced by varying the CdC1 2 post-deposition treatment temperature. We use high-resolution cathodoluminescence (CL) microscopy to study recombination and shallow defect levels in detail. Intensities from room temperature CL maps were compared across samples. We find that the CL intensity initially increases with grain size, as expected, but then plateaus as the grain size is increased further. The plateau is correlated with a decrease in the characteristic length-related to the carrier diffusion length-determined from CL intensity profiles near grain boundaries. In addition, low-temperature CL measurements demonstrate the evolution of the defect levels with CdC1 2 temperature.

cadmium telluride thin films↗
DOE OSTI2020

Impact of dopant-induced optoelectronic tails on open-circuit voltage in arsenic-doped Cd(Se)Te solar cells

Fluctuations refer to inhomogeneity in the distribution of donors and acceptors at the nanometer scale and occur in many compound solar cell materials such as Cu(In,Ga)Se 2 , Cu 2 ZnSn(S,Se) 4 , and CdSe x Te 1-x . In this work, numerical simulations show that these fluctuations produce not only electrostatic potential variation, but also, local changes in the carrier density and effective bandgap. For a CdSe x Te 1-x absorber doped with arsenic, simulations and cathodoluminescence data within single grains demonstrate how donor and acceptor densities—consistent with capacitance-voltage and secondary-ion mass-spectrometry data—produce tails in photoluminescence, quantum efficiency, and absorption measurements. Using multiple theoretical approaches, we demonstrate that the fluctuations can hinder expected performance gains from increased carrier density, and we describe the significant open-circuit voltage deficit observed in the CdSe x Te 1-x :As solar technology. Our results demonstrate that it is critical to characterize and reduce carrier compensation to realize a higher efficiency.

14 SOLAR ENERGY↗
DOE OSTI2020

The 2020 photovoltaic technologies roadmap

Over the past decade, the global cumulative installed photovoltaic (PV) capacity has grown exponentially, reaching 591 GW in 2019. Rapid progress was driven in large part by improvements in solar cell and module efficiencies, reduction in manufacturing costs and the realization of levelized costs of electricity that are now generally less than other energy sources and approaching similar costs with storage included. Given this success, it is a particularly fitting time to assess the state of the photovoltaics field and the technology milestones that must be achieved to maximize future impact and forward momentum. This roadmap outlines the critical areas of development in all of the major PV conversion technologies, advances needed to enable terawatt-scale PV installation, and cross-cutting topics on reliability, characterization, and applications. Each perspective provides a status update, summarizes the limiting immediate and long-term technical challenges and highlights breakthroughs that are needed to address them. In total, this roadmap is intended to guide researchers, funding agencies and industry in identifying the areas of development that will have the most impact on PV technology in the upcoming years.

14 SOLAR ENERGY↗
DOE OSTI2020

Sputtered p-Type Cu x Zn 1– x S Back Contact to CdTe Solar Cells

As thin-film cadmium telluride (CdTe) solar cells gain prominence, one particular challenge is optimizing contacts and their interfaces to transfer charge without losses in efficiency. Back contact recombination is still significant and will prevent CdTe solar technology from reaching its full potential in device efficiency, and transparent back contacts have not been developed for bifacial solar technology or multijunction solar cells. To address these challenges, here we investigate sputtered Cu x Zn 1– x S as a p-type semi-transparent back contact material to thin-film polycrystalline CdTe solar cells at Cu concentrations x = 0.30, 0.45, and 0.60. This material is selected for its high hole conductivity (160–2120 S cm –1 ), wide optical band gap (2.25–2.75 eV), and variable ionization potential (approximately 6–7 eV) that can be aligned to that of CdTe. We report that without device optimization, CdTe solar cells with these Cu x Zn 1– x S back contacts perform as well as control cells with standard ZnTe:Cu back contacts. We observe no reduction in external quantum efficiency, low contact barrier heights of approximately 0.3 eV, and carrier lifetimes on par with those of baseline CdTe. These cells are relatively stable over one year in air, with V OC and efficiency of the x = 0.30 cell decreasing by only 1 and 3%, respectively. Using scanning electron microscopy and scanning transmission electron microscopy to investigate the Cu x Zn 1– x S/CdTe interface, we demonstrate that the Cu x Zn 1– x S layer segregates into a bilayer of Cu-Te-S and Zn-Cd-S, and thermodynamic reaction calculations support these findings. Despite its bilayer formation, the back contact still functions well. This investigation explains some of the physical mechanisms governing the device stack, inspires future work to understand interfacial chemistry and charge transfer, and elicits optimization to achieve higher-efficiency CdTe cells.

14 SOLAR ENERGY↗
DOE OSTI2020

Imaging hole-density inhomogeneity in arsenic-doped CdTe thin films by scanning capacitance microscopy

We report nanometer-scale hole-density imaging in As-doped CdTe films by scanning capacitance microscopy (SCM). The hole-density profiling is validated by contrasting a CdTe cross-section sample made by molecular-beam epitaxy with systematically increased As doping in a staircase pattern over the range of 10 15 -10 18 /cm 3 within a single film. In polycrystalline films, the carrier distribution is significantly nonuniform, with inhomogeneity ranging from several hundred nm to several um and hole density varying by one order of magnitude (low 10^16 to low 10 17 /cm 3 ). This nonuniformity is distributed randomly, independent of the grain structure and grain boundaries (GBs). Kelvin probe force microscopy (KPFM) maps the surface potential and is correlated to cathodoluminescence (CL) and SCM by imaging over identical areas. Higher potential and lower CL intensity are found on GBs but not by SCM contrast; this indicates positive GB charging and recombination, but not GB-specific hole-density changes. The overall KPFM potential image is in rough agreement with the SCM carrier distribution and indicates band-edge potential fluctuations. Nonuniform carrier concentration, potential fluctuations, and defect recombination can all cause voltage and performance loss in As-doped CdTe solar technology.

14 SOLAR ENERGY↗
DOE OSTI2020

Thin-Film Solar Cells with 19% Efficiency by Thermal Evaporation of CdSe and CdTe

CdTe-based solar cells exhibiting 19% power conversion efficiency were produced using widely available thermal evaporation deposition of the absorber layers on SnO2-coated glass with or without a transparent MgZnO buffer layer. Evaporating CdSe and CdTe sequentially by thermal evaporation and subsequent CdCl2 annealing establishes efffective CdSeTe band grading as well as dense, large-grain films. These results show that high-performance II-VI photovoltaics can be made by inexpensive, commercially available evaporation systems without the need to build customized equipment, enabling CdTe photovoltaics research and manufacturing to be more accessible to the broader photovoltaics community.

14 SOLAR ENERGY↗