Engineering topics

Meyer III, Harry

Publications and source records attributed to Meyer III, Harry.

At least 19 records

DOE OSTI2024

Iodine Capture Studies of Silver Mordenite and Novel Alternative Metal Sorbents

Radioiodine is one of the radionuclides of concern when considering reprocessing of used nuclear fuel (UNF). It is expected to be released primarily in the dissolver off-gas (DOG) stream. Sorbents that target I 2 removal from a UNF processing off gas must perform efficiently under elevated temperatures in the presence of water vapor and nitrogen oxide gasses (NOx). Many studies have been conducted that examine the adsorption of iodine species in the presence of NOx gases through reduced silver-exchanged mordenite (Ag 0 Z), a zeolite mineral. This study characterizes the effects of iodine, water vapor, and nitrogen dioxide on the adsorption of I 2 by Ag 0 Z at lower temperatures suitable for comparison with novel Cu- and Bi- bearing sorbents which offer a non-RCRA alternative. When exposed to ‘harsh’ conditions such as I 2 , H 2 O, and NO 2 vapors carried by air, Cu 2 S-polyacrylonitrile (PAN) is more efficient than Ag 0 Z and all other novel sorbents, providing with 11% I capture efficiency. However, under ‘ideal’ conditions in which I 2 is carried by dry air), Ag 0 Z is more efficient than Cu 2 S-PAN and other novel sorbents, providing 74% I capture efficiency. To investigate this result and the overall performance of all sorbents tested, several characterization techniques were employed, including thermal gravimetric analysis, scanning electron microscopy – electron dispersion X-Ray spectroscopy, powder X-ray diffraction, and X-ray photoelectron spectroscopy. These techniques are discussed within this report. This document also includes a design and test plan update from Idaho National Laboratory as the next step in testing the high performing sorbents from thin-bed tests carried out by Oak Ridge National Laboratory.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Observation of tantalum deposition and growth on TiB2 and ZrB2 from PISCES-RF deuterium and helium plasma exposures

Deuterium and helium plasma exposures on bulk TiB2 and ZrB2 samples were performed using the PISCES-RF linear plasma device. 40 and 90 eV deuterium ion plasma exposures were performed at 240 and 800 °C sample temperatures, and 80 eV helium ion plasma exposures were performed at 800 °C sample temperatures. Following plasma exposures, it was discovered that two plasma conditions (90 eV deuterium and 80 eV helium at 800 °C) resulted in thick (>200 nm) tantalum-rich (>10 at%) surface features on the targets, presumably from tantalum sourced from a tantalum adapter mask or cap used as part of the target holder. This work aims to characterize these tantalum-rich features and examine the mechanisms of impurity deposition.Plasma-induced surface morphology of the tantalum-rich surface layers depends on plasma properties and target temperature and chemistry. Greater titanium sputtering compared to zirconium resulted in more distinct surface features in the TiB2 samples compared to the ZrB2 samples via increased, prompt deposition onto tantalum surface impurities. There is still uncertainty as to why thick tantalum deposition only occurred under some plasma exposure conditions but not others; it is likely due to tantalum sputtering by a combination of boron molecules from the targets and carbon-impurities in the tantalum mask or targets. Impurity driven surface features are a well-documented phenomena in samples exposed to plasma from linear plasma device facilities—this work confirms the occurrence of this and emphasizes the need for chemistry characterization of isolated post-mortem surface features in plasma-exposed samples.

Nuckols, Lauren↗

DOE OSTI2024

Copper–Carbon Nanotube Composites Enabled by Brush Coating for Advanced Conductors

There is a growing demand for advanced conductors with enhanced electrical properties to increase the energy efficiency in various applications. A promising strategy to achieve this involves the use of ultraconductive copper (UCC) composites that incorporate highly conductive carbon materials, such as carbon nanotubes (CNTs), into the copper matrix. In this study, we present a scalable brush coating technique to incorporate CNTs onto Cu substrates to produce Cu–CNT–Cu composites. The process involves brush coating the CNT solution on Cu tape substrates, followed by vacuum-assisted thermal removal of organic moieties (e.g., surfactant/polymer). This step ensures the creation of a uniformly distributed CNT network within the Cu matrix. By addition of a thin film Cu overlayer, the fabricated Cu–CNT–Cu composite architecture demonstrates similar electrical conductivity, increased current carrying capacity, and enhanced mechanical properties compared to pure Cu reference tapes. Finally, the performance characteristics of these UCC tapes along with the scalability of the brush coating approach hold great promise for the fabrication of advanced conductors for wide-ranging energy applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Detailed Characterization of Vitrinite-Rich Subbituminous and Bituminous Coals for Utilization in Carbon Fiber Precursor Production

Chemical structures of candidate coals (one subbituminous coal from the Powder River Basin and three bituminous Eastern US coals) were examined for potential low-cost carbon fiber precursor production. Here, the structural evaluation examined the carbon skeleton ( 13 C nuclear magnetic resonance (NMR) and high-resolution transmission electron microscopy (HRTEM)), the heteroatom functionality (X-ray photoelectron spectroscopy (XPS) Fourier transform infrared spectroscopy (FTIR) and NMR), the structural ordering and distribution of PAH sizes (HRTEM), and an estimation of the molecular weight distribution (laser desorption ionization mass spectrometry, LDIMS). The molecular compositional distributions were also evaluated for a mixed solvent extract (atmospheric pressure photoionization, 21 T Fourier transform ion cyclotron resonance mass spectrometry, FT-ICR MS). Significant structural differences existed between the subbituminous and bituminous coals, as expected with coalification (with the bituminous coals having a higher carbon content, lower oxygen content, higher aromaticity values, larger cluster sizes, and so forth). While the bituminous coals were similar in structure (close in rank with Blue Gem being hvAb and the rest being hvBb), structural differences were still evident. Specifically, structural similarities were evident for the average properties of Herrin and Springfield coals: same rank, similar moisture, and volatile matter yields, along with similar aromaticity and carbon and hydrogen content. However, significant structural differences were observed at the molecular level by 21 T FT-ICR MS, which showed that the Springfield coal was structurally more complex. Specifically, 21740, 16931, 30190, and 12982 unique elemental compositions were identified for the Monarch, Herrin, Springfield, and Blue Gem coals, further illustrating the complexity of the coal.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2024

Characterization of fluidized bed chemical vapor deposition ZrC coatings on PyC/YSZ kernels deposited under differing conditions

In this study, coated fuel particle architectures with ZrC coatings are candidate fuels for advanced power reactors and space nuclear propulsion (SNP) concepts. Owing to its relevance to SNP, the composition, microstructure, and mechanical properties of eight ZrC coatings prepared by fluidized bed chemical vapor deposition were evaluated. Evaluation by SEM and EBSD showed that all grains were columnar. Across the various examined samples, minor axis diameters varied between 0.3 and 1.1 μm, and major axis diameters varied between 0.4 and 2.3 μm. Major and minor diameters increased with thickness particularly at higher deposition temperatures in which the major grain axis (from an ellipse fit to the grain shape) increased by 2.5 μm over the entire coating. Coatings with higher reactive gas flows and Zr/C concentrations closer to 1 were observed to contain nanocrystalline graphite deposits. Reactive gas flow doubling led to increases in coating thickness from around 10–15 μm to around 22–27 μm.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

In Situ Neutron Scattering Studies on the Oxidation and Reduction of CeO 2 and Pt–CeO 2 Nanorods

The oxygen vacancy structure of ceria plays a key role in its performance as a favored material for catalysis applications. Here, in this work, we develop an understanding of the effects of Pt loading on the structural evolution of ceria nanorods under redox gas environments that mimic real automotive catalytic converters. In situ neutron scattering studies under redox flow reveal that both CeO 2 and Pt–CeO 2 nanorods share a bulk fluorite structure with the presence of surface Frenkel-type oxygen defects. However, Pt–CeO 2 nanorods are more easily reducible than CeO 2 rods as evidenced by an increased concentration of Ce 3+ , determined by NAP-XPS. Importantly, this work finds no evidence of oxygen vacancy ordered surface reconstruction which has been reported in earlier ex situ investigations. Thus, this work highlights the discrepancy between ex situ and in situ structural observations and emphasizes the need for robust in situ investigations of catalysts to develop industrially relevant materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Formation of carbon and oxygen rich surface layer on high purity magnesium by atmospheric carbon dioxide plasma

Carbon and oxygen-rich corrosion barrier layer formed on Mg by a simple and scalable CO 2 atmospheric plasma (CO 2 -AP) process. The reactive CO 2 -AP interacts with the Mg surface and forms a unique layered structure with the top MgCO 3 /MgO-intermixed particulates pillars and the bottom dense layer. The surface features were simultaneously formed on the nano-/micro-structured MgO layer by carbonate molecules, plasma-active CO 2 molecules, and/or other volatile organic compounds on the nano-/micro-structured MgO particle layer. The resulting surfaces after CO 2 -AP were either hydrophobic or hydrophilic and exhibited lower anodic current or high resistance for Mg corrosion. For the hydrophobic surfaces of CO 2 -AP treated Mg, molecular dynamic simulations were performed to understand the origin of hydrophobicity and identified that the amorphous carbon layers formed on the Mg surface are the source. The environmentally benign abundant-gas-based process enables the cost reduction associated with waste treatment, generation of by-product, and supply of raw material.

36 MATERIALS SCIENCE↗

DOE OSTI2022

In situ characterization of phase transformations in petroleum pitch by high temperature X-ray diffraction

The phase transformation from isotropic to mesophase of a petroleum-derived pitch was monitored by in situ X-ray diffraction at 410 °C. The kinetics of the transformation were characterized by monitoring the growth of a broad peak at 2θ~24° and could be described by Avrami’s equation. The volatilization of low molecular weight components originally present in the pitch, or produced during the condensation reaction, was assessed by thermal gravimetry analysis, following the same thermal history. Ex situ characterizations of the pitch precursor before and after thermal treatment provided insight into the evolution of the molecular structure associated with mesophase generation (optical polarized microscopy, molecular weight distribution by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry, X-ray photoelectron spectroscopy, Auger spectroscopy, and thermal stability). Here, this investigation demonstrates the value of using complementary in situ and ex situ experimental techniques to characterize complex mechanisms during the processing of organic materials.

02 PETROLEUM↗

DOE OSTI2021

Operando Analysis of Gas Evolution in TiNb 2 O 7 (TNO)-Based Anodes for Advanced High-Energy Lithium-Ion Batteries under Fast Charging

TiNb 2 O 7 (TNO) is regarded as one of the promising next-generation anode materials for lithium-ion batteries (LIBs) due to its high rate capabilities, higher theoretical capacity, and higher lithiation voltage. Furthermore, this enables the cycling of TNO-based anodes under extreme fast charging (XFC) conditions with a minimal risk of lithium plating compared to that of graphite anodes. Here, the gas evolution in real time with TNO-based pouch cells is first reported via operando mass spectrometry. The main gases are identified to be CO 2 , C 2 H 4 , and O 2 . A solid–electrolyte interphase is detected on TNO, which continues evolving, forming, and dissolving with the lithiation and delithiation of TNO. The gas evolution can be significantly reduced when a protective coating is applied on the TNO particles, reducing the CO 2 and C 2 H 4 evolution by ~2 and 5 times, respectively, at 0.1C in a half-cell configuration. The reduction on gas generation in full cells is even more pronounced. The surface coating also enables 20% improvement in capacity under XFC conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

RF sheath induced sputtering on Proto-MPEX part 2: Impurity transport modeling and experimental comparison

The Prototype Material Plasma Exposure eXperiment (Proto-MPEX) is a pulsed linear plasma device that uses a radio frequency (RF) helicon antenna and a helicon ceramic window as the plasma ionization source. Modeling performed within this work on the helicon operations predicts hot spots on the helicon ceramic window due to an RF-induced sheath. The RF sheath potential leads to physical sputtering of the ceramic window predominantly where the helicon antenna sits around the helicon window. The role of oxygen in sputtering within Proto-MPEX is also investigated and is needed to match the experimental data. Experiments on Proto-MPEX show reasonable agreement with the modeled erosion/redeposition pattern on the helicon window, and the modeled impurity flux to the target shows radial transport within the device as expected from classical collisional impurity transport. Temperature screening of impurities is shown to be needed for Proto-MPEX to reduce impurity flux to the target. The modeling approach used in this work can be applied to other plasma RF applications for the determination of impurity production and transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Al 2 O 3 /TiO 2 coated separators: Roll-to-roll processing and implications for improved battery safety and performance

Heat generation is one of the major concerns with lithium-ion batteries (LIB) while charging them at higher currents, which could inadvertently impact the rate performance and reduce the safety of the cell. Polymer separator is one of the least thermal conductive components of a LIB. In addition, commercial separators for LIB are made from polyolefin membranes that tend to shrink and curl at higher temperatures due to their lower melting temperature (~130 °C). Developing separators with improved thermal stability and higher electrolyte uptake is essential for enhancing the safety as well as the performance of the LIB. In this work, a thin layer of ceramic coatings (Al 2 O 3 and TiO 2 ) is applied on propylene (PP) membrane to improve the thermal stability and electrolyte affinity without compromising the rate performance. A slurry with 100% Al 2 O 3 coated on the polypropylene separator exhibited the best improvement in thermal stability ( shrinkage of 0.6% vs 6.0% for uncoated membrane) and excellent rate performance with 92% capacity retention at 2C. The Al 2 O 3 coated separator demonstrated excellent electrolyte wettability compared to the uncoated membrane. The cross-plane thermal conductivity of the ceramic coated separators is analyzed to understand their heat transfer behavior. The thermal conductivity of the separator is improved by ~3.2 times with the Al 2 O 3 coating.

25 ENERGY STORAGE↗

DOE OSTI2021

Molten Salt Assisted Low-Temperature Electro-Catalytic Graphitization of Coal Chars

A great effort has been centered around developing clean energy technologies (energy storage devices) to curtail burning fossil fuels' deleterious environmental effects. Rechargeable batteries [lithium-ion batteries (LIBs)] are among the most invested and investigated storage devices showing potential to transform fossil fuel-powered mobility to next-generation safe electromobility. However, LIBs powered electric vehicles (EV) are expensive due to the high-cost graphite anode associated with LIBs. Herein, the synthesis of low-cost, highly crystalline nano-graphite with a tunable microstructural architecture has been demonstrated via molten salt assisted low-temperature electro-catalytic graphitization of coal chars, traditionally non-graphitizable carbon. Thus, graphite derived from coal chars exhibited nanoflake architecture and delivered high reversible capacity, stable long cycle life, and excellent electrochemical performance under fast charging/discharging conditions (5C, ~12 min charge/discharge time). This finding paves the way to manufacture cost-effective high-energy-density batteries using as-synthesized graphite from readily available coal sources that could propel the EVs to the next level.

25 ENERGY STORAGE↗

DOE OSTI2021

Wear penalty for steel rubbing against hard coatings in reactive lubricants due to tribochemical interactions

Hard coatings and surface adsorptive/reactive lubricants are two common strategies for improving wear protection, but what if they are used together? In this study, steel-steel and steel-coating sliding was investigated in boundary lubrication of polar and non-polar oils containing a ZDDP or an ionic liquid. Two hard coatings, diamond-like-carbon (DLC) and chromium nitride (CrN), were used. Furthermore, for a steel-steel contact, wear was effectively reduced by using a more surface reactive lubricant, as expected. However, the steel ball wear was increased against a hard coating and further worsened with a more polar oil and/or a more surface reactive additive. The wear mechanism is proposed as a combined effect of physicochemical interactions with the lubricant, mechanical polishing by the counterface, and material adhesion.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Surface and subsurface characterization of laser-interference structured Ti6Al4V

Ti6Al4V specimens were exposed to high-energy laser pulses of 1.24 J/cm 2 fluences per pulse using a two-beam optical configuration to attain laser-interference. In addition to the formation of periodic surface textures by laser-interference, scanning electron microscope (SEM) images demonstrated several microstructural changes on the surface processed. Moreover, the surface and subsurface of Ti6Al4V specimens were characterized for the as-received and laser-interference processed conditions using x-ray photoelectron spectroscopy (XPS) and electron energy dispersive spectroscopy (EDS). The XPS data showed that this laser technique is effective at removal of surface contaminants for Ti6Al4V. The XPS analysis also revealed the formation of an oxy-nitride layer on the laser treated material. Finally, the microstructure analysis indicates that grain refinement, dendrite and twin structures were found near the surface due to laser processing.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Low-Cost Transformation of Biomass-Derived Carbon to High-Performing Nano-graphite via Low-Temperature Electrochemical Graphitization

Graphite, an essential component of energy storage devices, is traditionally synthesized via an energy-intensive thermal process (Acheson process) at ~3300 K. However, the battery performance of such graphite is abysmal under fast-charging conditions, which is deemed essential for the propulsion of electric vehicles to the next level. Herein, a low-temperature electrochemical transformation approach has been demonstrated to afford a highly crystalline nano-graphite with the capability of tuning interlayer spacing to enhance the lithium diffusion kinetics in molten salts at 850 °C. The essence of our strategy lies in the effective electrocatalytic transformation of carbon to graphite at a lower temperature that could significantly increase the energy savings, reduce the cost, shorten the synthesis time, and replace the traditional graphite synthesis. The resulting graphite exhibits high purity, crystallinity, a high degree of graphitization, and a nanoflake architecture that all ensure fast lithium diffusion kinetics (~2.0 × 10 –8 cm2 s –1 ) through its nanosheet. Such unique features enable outstanding electrochemical performance (~200 mA h g –1 at 5C for 1000 cycles, 1C = 372 mA g –1 ) as a fast-charging anode for lithium-ion batteries. Overall, this finding paves the way to make high energy-density fast-charging batteries that could boost electromobility.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

New Synthesis Strategies to Improve Co-Free LiNi0.5Mn0.5O2 Cathodes: Early Transition Metal d0 Dopants and Manganese Pyrophosphate Coating

In this work, we report solution-based doping and coating strategies to improve the electrochemical performance of the Co-free layered oxide cathode LiNi0.5Mn0.5O2 (LNMO). Small amounts of d0 dopants (e.g., Mo6+and Ti4+, 0.5-1 at. %) increase the cathode’s specific capacity, cycling stability, and rate capability. More specifically, a Mo-doped cathode with the nominal composition LiNi0.495Mn0.495Mo0.01O2 achieves a high reversible capacity of 180 mAh/g at 20 mA/g with good retention at higher rates (e.g., 120 mAh/g at 100 mA/g). Effects of 1 at.% Mo dopant on the cathode structure were studied using a suite of characterization tools including X-ray diffraction (XRD), Raman spectroscopy, and transmission electron microscopy (TEM). These measurements demonstrate that Mo6+ reduces Li+/Ni2+cation mixing and mitigates undesirable phase transformations near the cathode surface during cycling. This work also reports the use of an inorganic Mn2P2O7 coating which enhances cycling stability, presumably through formation of a stable cathode electrolyte interphase (CEI) layer. Overall, the synthesis approaches reported herein are quite general and can potentially be expanded to other high voltage LIB cathodes.

Co-free cathodes, d0 cation, pyrophosphate coating↗

DOE OSTI2020

Modified Coal Char Materials with High Rate Performance for Battery Applications

Global energy consumption has been rising since the early 2000s, and most of the energy supply still comes from burning fossil fuels. Considering the detrimental environmental impacts of fossil fuels, such as CO 2 emissions, it is crucial to develop clean energy technologies, such as storage devices that can advance long-term reversible and sustainable energy resources. In this work, we demonstrate the direct use of coal char in anodes tailored for both lithium-ion and sodium-ion batteries. The findings show that acid treatment followed by high-temperature argon annealing results in coal char particles with the desired porous structure, surface properties, and turbostratic nanodomains that deliver high reversible capacity and maintain good electrochemical performance at high rates up to 10C. Long-term cycling stability for 500 cycles can be achieved in cells comprising NMC cathodes at 1C with 73.2% capacity retention. In conclusion, this study sheds light on potential energy storage use cases for coal char outside its traditional utilization.

25 ENERGY STORAGE↗

DOE OSTI2020

Direct Characterization of Atomically Dispersed Catalysts: Nitrogen-Coordinated Ni Sites in Carbon-Based Materials for CO 2 Electroreduction

Metal, nitrogen-doped carbon materials have attracted interest as heterogenous catalysts that contain MN x active sites that are analogous to molecular catalysts. Of particular interest is Ni,N-doped carbon, a catalyst that is active for the electrochemical reduction of CO 2 to CO. Critical to the understanding of these materials is proof of single atomic sites and characterization of the environment surrounding the metal atom; however, directly probing this coordination remains challenging. This challenge is addressed in this study by combining scanning transmission electron microscopy (STEM), single atom electron energy loss spectroscopy (EELS), and time-of-flight secondary ion mass spectrometry (ToF-SIMS). Through STEM imaging, atomic dispersion of Ni in the carbon framework is confirmed and image analyses are utilized to give semiquantitative estimates of neighbor distance distributions and site densities of Ni atoms. Atomic resolution EELS demonstrates that N and Ni are colocated at the single Ni atom sites suggesting Ni–N coordination. ToF-SIMS reveals a distribution of NiN x C y - fragments that reflect the Ni–N bonding environments within Ni,N-doped carbon. The fragmentation from Ni,N-doped carbon is similar to Ni phthalocyanine, suggesting the existence of heterogenized, molecular-like NiN 4 active sites which motivates future studies that leverage insight from molecular catalysis design to develop next-generation heterogeneous catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗