Search NASA⌕ Search

Engineering topics

Meyerhofer, D D

Publications and source records attributed to Meyerhofer, D D.

At least 19 records

Magnetic collimation of relativistic positrons and electrons from high intensity laser–matter interactions

Collimation of positrons produced by laser-solid interactions has been observed using an externally applied axial magnetic field. The collimation leads to a narrow divergence positron beam, with an equivalent full width at half maximum beam divergence angle of 4° vs the un-collimated divergence of about 20°. A fraction of the laser-produced relativistic electrons with energies close to those of the positrons is collimated, so the charge imbalance ratio (n{sub e−}/n{sub e+}) in the co-propagating collimated electron-positron jet is reduced from ∼100 (no collimation) to ∼2.5 (with collimation). The positron density in the collimated beam increased from 5 × 10{sup 7} cm{sup −3} to 1.9 × 10{sup 9} cm{sup −3}, measured at the 0.6 m from the source. This is a significant step towards the grand challenge of making a charge neutral electron-positron pair plasma jet in the laboratory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Spherical shock-ignition experiments with the 40 + 20-beam configuration on OMEGA

Spherical shock-ignition experiments on OMEGA used a novel beam configuration that separates low-intensity compression beams and high-intensity spike beams. Significant improvements in the performance of plastic-shell, D 2 implosions were observed with repointed beams. The analysis of the coupling of the high-intensity spike beam energy into the imploding capsule indicates that absorbed hot-electron energy contributes to the coupling. The backscattering of laser energy was measured to reach up to 36% at single-beam intensities of ~ 8 x 10 15 W/cm/ 2 . Hard x-ray measurements revealed a relatively low hot-electron temperature of ~30 keV independent of intensity and timing. At the highest intensity, stimulated Brillouin scattering occurs near and above the quarter-critical density and the two-plasmon-decay instability is suppressed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Emittance of positron beams produced in intense laser plasma interaction

The first measurement of the emittance of intense laser-produced positron beams has been made. The emittance values were derived through measurements of positron beam divergence and source size for different peak positron energies under various laser conditions. For one of these laser conditions, we used a one dimensional pepper-pot technique to refine the emittance value. The laser-produced positrons have a geometric emittance between 100 and 500 mm{center_dot}mrad, comparable to the positron sources used at existing accelerators. With 10{sup 10}-10{sup 12} positrons per bunch, this low emittance beam, which is quasi-monoenergetic in the energy range of 5-20 MeV, may be useful as an alternative positron source for future accelerators.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Heavy-ion emission from short-pulse laser-plasma interactions with thin foils

A Thomson parabola ion spectrometer, implemented on the Laboratory for Laser Energetics Multi-Terawatt laser facility, has been used to study heavy-ion acceleration from ultra-intense laser-plasma interactions. These studies were conducted using 20 {mu}m-thick flat foil targets with on-target intensities of 4-5 Multiplication-Sign 10{sup 19} W-cm{sup -2}. Several charge states of energetic heavy ions were accelerated from the rear of Al and Cu foils in the presence of hydrocarbon contaminants. In contrast to previous work, we show that the mean and maximum energies of each heavy-ion species scale linearly with only the charge of the ion, and not the charge-to-mass ratio, implying that the space-charge is not readily depleted as ions expand. It has been shown previously and observed here that the maximum heavy-ion energies are lower than that of protons, though a fundamental explanation for this discrepancy has not been provided. We show how a two-temperature electron distribution, observed in these experiments, explains these observations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

OMEGA polar-drive target designs

Low-adiabat polar-drive (PD) [Skupsky et al., Phys. Plasmas 11, 2763 (2004)] implosion designs for the OMEGA [Boehly et al., Opt. Commun. 133, 495 (1997)] laser are described. These designs for cryogenic deuterium-tritium and warm plastic shells use a temporal laser pulse shape with three pickets followed by a main pulse [Goncharov et al., Phys. Rev. Lett. 104, 165001 (2010)]. The designs are at two different on-target laser intensities, with different in-flight aspect ratios (IFARs). These designs permit studies of implosion energetics and target performance closer to ignition-relevant intensities ({approx}7 Multiplication-Sign 10{sup 14} W/cm{sup 2} at the quarter-critical surface, where nonlocal heat conduction and laser-plasma interactions can play an important role) but at lower values of IFAR {approx} 22 or at lower intensity ({approx}3 Multiplication-Sign 10{sup 14} W/cm{sup 2}) but at a higher IFAR (IFAR {approx} 32, where shell instability can play an important role). PD geometry requires repointing of laser beams to improve shell symmetry. The higher-intensity designs optimize target performance by repointing beams to a lesser extent, compensating for the reduced equatorial drive by increasing the energies of the repointed beams. They also use custom beam profiles that improve equatorial illumination at the expense of irradiation at higher latitudes. These latter designs will be studied when new phase plates for the OMEGA Laser System, corresponding to the custom beam profiles, are obtained.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Rayleigh-Taylor-induced magnetic fields in laser-irradiated plastic foils

Experimental observations of magnetic fields generated by Rayleigh-Taylor growth in laser-irradiated planar foils are presented. X-ray and monoenergetic proton radiographic techniques were used to probe plastic foils with seeded surface perturbations at different times during the evolution. Protons deflected by fields in the target cause modulations in proton fluence at the seed wavelength of 120 {mu}m. Path-integrated magnetic-field strengths were inferred from modulations in proton fluence using a discrete-Fourier-transform analysis technique and found to increase from 10 to 100 T-{mu}m during linear growth. Electron thermal conduction was shown to be unaffected by Rayleigh-Taylor-induced magnetic fields during the linear growth phase.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Study of Rayleigh–Taylor growth in directly driven cryogenic-deuterium targets

Direct-drive, Rayleigh–Taylor growth experiments in liquid deuterium (D2) were performed on the OMEGA laser [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] using planar cryogenic targets at a laser intensity of ∼4 × 1014 W/cm2. These are the first Rayleigh–Taylor measurements in deuterium at conditions relevant to inertial confinement fusion using a mass preimposed initial modulation. The measured modulation optical depths are in agreement with the 2D hydrodynamics code DRACO using flux-limited local thermal transport, providing an important step in the experimental validation of simulations for direct-drive ignition.

Hager, J. D.↗

Experimental reduction of laser imprinting and Rayleigh–Taylor growth in spherically compressed, medium-Z-doped plastic targets

The effect of medium-Z doping of plastic ablators on laser imprinting and Rayleigh–Taylor (RT) instability growth was studied using spherical direct-drive implosions on the OMEGA Laser System [T. R. Boehly et al., Opt. Commun. 133, 495 (1977)]. The targets were spherical plastic (CH) shells, with an outer diameter of 860 μm and a thickness of 22 μm, volume doped with a varied concentration of Si (4.3% and 7.4%) and Ge (3.9%). The targets were imploded with 48 beams with a low-adiabat, triple-picket laser shape pulse with a peak intensity of 4×1014W/cm2, and a pulse duration of 2.5 ns. The shells were x-ray radiographed through a 40 -μm opening in the side of the target. The results show that volumetric impurity doping strongly reduces the shell density modulation and the instability growth rate. The amplitude of the initial imprint is reduced by a factor of 2.5 ±0.5 for CH[4.3% Si] targets and by a factor of 3 ±0.5 for CH[7.4% Si] and CH[3.9% Ge] targets. At the end of the acceleration phase, the reduction factor becomes 3 ±0.5 and 5 ± 0.5, correspondingly. The RT instability growth rate in doped targets is reduced by a factor of 1.5 compared to undoped ones. Simulations using the two-dimensional, radiation-hydrodynamics code draco show good agreement with the measurements

Fiksel, G.↗

Crossed-beam energy transfer in direct-drive implosions

Direct-drive-implosion experiments on the OMEGA laser [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] have showed discrepancies between simulations of the scattered (non-absorbed) light levels and measured ones that indicate the presence of a mechanism that reduces laser coupling efficiency by 10%-20%. This appears to be due to crossed-beam energy transfer (CBET) that involves electromagnetic-seeded, low-gain stimulated Brillouin scattering. CBET scatters energy from the central portion of the incoming light beam to outgoing light, reducing the laser absorption and hydrodynamic efficiency of implosions. One-dimensional hydrodynamic simulations including CBET show good agreement with all observables in implosion experiments on OMEGA. Three strategies to mitigate CBET and improve laser coupling are considered: the use of narrow beams, multicolor lasers, and higher-Z ablators. Experiments on OMEGA using narrow beams have demonstrated improvements in implosion performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A polar-drive-ignition design for the National Ignition Facility

Polar drive [Skupsky et al., Phys. Plasmas 11, 2763 (2004)] will enable direct-drive experiments to be conducted on the National Ignition Facility (NIF) [Miller et al., Opt. Eng. 43, 2841 (2004)], while the facility is configured for x-ray drive. A polar-drive ignition design for the NIF has been developed that achieves a gain of 32 in two-dimensional (2-D) simulations, which include single- and multiple-beam nonuniformities and ice and outer-surface roughness. This design requires both single-beam UV polarization smoothing and one-dimensional (1-D) multi-frequency modulator (MFM) single-beam smoothing to achieve the required laser uniformity. The multi-FM smoothing is employed only during the low-intensity portion of the laser pulse, allowing for the use of sufficient smoothing-by-spectral-dispersion bandwidth while maintaining safe laser operations during the high-intensity part of the pulse. This target is robust to all expected sources of perturbations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hot-spot mix in ignition-scale implosions on the NIF

Ignition of an inertial confinement fusion (ICF) target depends on the formation of a central hot spot with sufficient temperature and areal density. Radiative and conductive losses from the hot spot can be enhanced by hydrodynamic instabilities. The concentric spherical layers of current National Ignition Facility (NIF) ignition targets consist of a plastic ablator surrounding a thin shell of cryogenic thermonuclear fuel (i.e., hydrogen isotopes), with fuel vapor filling the interior volume [S. W. Haan et al., Phys. Plasmas 18, 051001 (2011)]. The Rev. 5 ablator is doped with Ge to minimize preheat of the ablator closest to the DT ice caused by Au M-band emission from the hohlraum x-ray drive [D. S. Clark et al., Phys. Plasmas 17, 052703 (2010)]. Richtmyer-Meshkov and Rayleigh-Taylor hydrodynamic instabilities seeded by high-mode () ablator-surface perturbations can cause Ge-doped ablator to mix into the interior of the shell at the end of the acceleration phase [B. A. Hammel et al., Phys. Plasmas 18, 056310 (2011)]. As the shell decelerates, it compresses the fuel vapor, forming a hot spot. K-shell line emission from the ionized Ge that has penetrated into the hot spot provides an experimental signature of hot-spot mix. The Ge emission from tritium-hydrogen-deuterium (THD) and deuterium-tritium (DT) cryogenic targets and gas-filled plastic-shell capsules, which replace the THD layer with a mass-equivalent CH layer, was examined. The inferred amount of hot-spot-mix mass, estimated from the Ge K-shell line brightness using a detailed atomic physics code [J. J. MacFarlane et al., High Energy Density Phys. 3, 181 (2006)], is typically below the 75-ng allowance for hot-spot mix [S. W. Haan et al., Phys. Plasmas 18, 051001 (2011)]. Predictions of a simple mix model, based on linear growth of the measured surface-mass modulations, are consistent with the experimental results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Inertial confinement fusion implosions with imposed magnetic field compression using the OMEGA Laser

Experiments applying laser-driven magnetic-flux compression to inertial confinement fusion (ICF) targets to enhance the implosion performance are described. Spherical plastic (CH) targets filled with 10 atm of deuterium gas were imploded by the OMEGA Laser, compare Phys. Plasmas 18, 056703 or Phys. Plasmas 18, 056309. Before being imploded, the targets were immersed in an 80-kG magnetic seed field. Upon laser irradiation, the high implosion velocities and ionization of the target fill trapped the magnetic field inside the capsule, and it was amplified to tens of megagauss through flux compression. At such strong magnetic fields, the hot spot inside the spherical target was strongly magnetized, reducing the heat losses through electron confinement. The experimentally observed ion temperature was enhanced by 15%, and the neutron yield was increased by 30%, compared to nonmagnetized implosions [P. Y. Chang et al., Phys. Rev. Lett. 107, 035006 (2011)]. This represents the first experimental verification of performance enhancement resulting from embedding a strong magnetic field into an ICF capsule. Experimental data for the fuel-assembly performance and magnetic field are compared to numerical results from combining the 1-D hydrodynamics code LILAC with a 2-D magnetohydrodynamics postprocessor.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Using high-intensity laser-generated energetic protons to radiograph directly driven implosions

The recent development of petawatt-class lasers with kilojoule-picosecond pulses, such as OMEGA EP [L. Waxer et al., Opt. Photonics News 16, 30 (2005)], provides a new diagnostic capability to study inertial-confinement-fusion (ICF) and high-energy-density (HED) plasmas. Specifically, petawatt OMEGA EP pulses have been used to backlight OMEGA implosions with energetic proton beams generated through the target normal sheath acceleration (TNSA) mechanism. This allows time-resolved studies of the mass distribution and electromagnetic field structures in ICF and HED plasmas. This principle has been previously demonstrated using Vulcan to backlight six-beam implosions [A. J. Mackinnon et al., Phys. Rev. Lett. 97, 045001 (2006)]. The TNSA proton backlighter offers better spatial and temporal resolution but poorer spatial uniformity and energy resolution than previous D{sup 3}He fusion-based techniques [C. Li et al., Rev. Sci. Instrum. 77, 10E725 (2006)]. A target and the experimental design technique to mitigate potential problems in using TNSA backlighting to study full-energy implosions is discussed. The first proton radiographs of 60-beam spherical OMEGA implosions using the techniques discussed in this paper are presented. Sample radiographs and suggestions for troubleshooting failed radiography shots using TNSA backlighting are given, and future applications of this technique at OMEGA and the NIF are discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Towards laboratory produced relativistic electron–positron pair plasmas

We review recent experimental results on the path to producing electron–positron pair plasmas using lasers. Relativistic pair-plasmas and jets are believed to exist in many astrophysical objects and are often invoked to explain energetic phenomena related to Gamma Ray Bursts and Black Holes. On earth, positrons from radioactive isotopes or accelerators are used extensively at low energies (sub-MeV) in areas related to surface science positron emission tomography and basic antimatter science. Experimental platforms capable of producing the high-temperature pair-plasma and high-flux jets required to simulate astrophysical positron conditions have so far been absent. In the past few years, we performed extensive experiments generating positrons with intense lasers where we found that relativistic electron and positron jets are produced by irradiating a solid gold target with an intense picosecond laser pulse. The positron temperatures in directions parallel and transverse to the beam both exceeded 0.5 MeV, and the density of electrons and positrons in these jets are of order 1016 cm -3 and 1013 cm -3 , respectively. With the increasing performance of high-energy ultra-short laser pulses, we expect that a high-density, up to 1018 cm -3 , relativistic pair-plasma is achievable, a novel regime of laboratory-produced hot dense matter.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Shock timing on the National Ignition Facility: First Experiments

An experimental campaign to tune the initial shock compression sequence of capsule implosions on the National Ignition Facility (NIF) was initiated in late 2010. The experiments use a NIF ignition-scale hohlraum and capsule that employs a reentrant cone to provide optical access to the shocks as they propagate in the liquid deuterium-filled capsule interior. The strength and timing of the shock sequence is diagnosed with velocity interferometry that provides target performance data used to set the pulse shape for ignition capsule implosions that follow. From the start, these measurements yielded significant new information on target performance, leading to improvements in the target design. We describe the results and interpretation of the initial tuning experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The direct measurement of ablation pressure driven by 351-nm laser radiation

The instantaneous scaling of ablation pressure to laser intensity is directly inferred for ramp compression of diamond targets irradiated by 351-nm light. Continuously increasing pressure profiles from 100 to 970 GPa are produced by direct-drive laser ablation at intensities up to 7 × 1013 W/cm2. The free-surface velocity on the rear of the target is used to directly infer the instantaneous ablation-pressure profile at the front of the target. The laser intensity on target is determined by laser power measurements and fully characterized laser spots. The ablation pressure is found to depend on the laser intensity as P(GPa)=42(±3)[I(TW/cm2)]0.71(±0.01).

Fratanduono, D. E.↗

Measurements of the Differential Cross Sections for the Elastic n-{sup 3}H and n-{sup 2}H Scattering at 14.1 MeV by Using an Inertial Confinement Fusion Facility

For the first time the differential cross section for the elastic neutron-triton (n-{sup 3}H) and neutron-deuteron (n-{sup 2}H) scattering at 14.1 MeV has been measured by using an inertial confinement fusion facility. In these experiments, which were carried out by simultaneously measuring elastically scattered {sup 3}H and {sup 2}H ions from a deuterium-tritium gas-filled inertial confinement fusion capsule implosion, the differential cross section for the elastic n-{sup 3}H scattering was obtained with significantly higher accuracy than achieved in previous accelerator experiments. The results compare well with calculations that combine the resonating-group method with an ab initio no-core shell model, which demonstrate that recent advances in ab initio theory can provide an accurate description of light-ion reactions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗