Search NASA⌕ Search

Engineering topics

Meyers, M. A.

Publications and source records attributed to Meyers, M. A..

Collapse of helium-filled voids in extreme deformation: Dislocation mechanisms

The mechanisms responsible for the collapse of helium-filled bubbles during the passage of shock waves in monocrystalline copper are revealed. Both internal pressure (caused by pre-existing helium atoms) and bubble size are varied in molecular dynamics simulations to understand the atomistic scale deformation as they are subjected to shock compression at pressures of 48, 123, and 170 GPa, corresponding to particle velocities of 1.0, 2.0, and 2.5 km/s. Both empty and helium filled bubbles serve as dislocation sources, generating intense, localized plastic regions. There are distinct differences in the collapse of empty voids compared to He-filled bubbles, the former requiring less stress and generating a greater density of dislocations for a given shock strength. Additionally, a generalized model for dislocation emission is proposed, where the inclusion of shear stress generated by the helium bubble increases the critical stress to generate dislocations at the defect surface, demonstrating the change in plastic deformation.

36 MATERIALS SCIENCE↗

The role of pre-existing heterogeneities in materials under shock and spall

There has been a challenge for many decades to understand how heterogeneities influence the behavior of materials under shock loading, eventually leading to spall formation and failure. Experimental, analytical, and computational techniques have matured to the point where systematic studies of materials with complex microstructures under shock loading and the associated failure mechanisms are feasible. This is enabled by more accurate diagnostics as well as characterization methods. As interest in complex materials grows, understanding and predicting the role of heterogeneities in determining the dynamic behavior becomes crucial. Early computational studies, hydrocodes, in particular, historically preclude any irregularities in the form of defects and impurities in the material microstructure for the sake of simplification and to retain the hydrodynamic conservation equations. Contemporary computational methods, notably molecular dynamics simulations, can overcome this limitation by incorporating inhomogeneities albeit at a much lower length and time scale. This review discusses literature that has focused on investigating the role of various imperfections in the shock and spall behavior, emphasizing mainly heterogeneities such as second-phase particles, inclusions, and voids under both shock compression and release. Pre-existing defects are found in most engineering materials, ranging from thermodynamically necessary vacancies, to interstitial and dislocation, to microstructural features such as inclusions, second phase particles, voids, grain boundaries, and triple junctions. This literature review explores the interaction of these heterogeneities under shock loading during compression and release. Systematic characterization of material heterogeneities before and after shock loading, along with direct measurements of Hugoniot elastic limit and spall strength, allows for more generalized theories to be formulated. Further, continuous improvement toward time-resolved, in situ experimental data strengthens the ability to elucidate upon results gathered from simulations and analytical models, thus improving the overall ability to understand and predict how materials behave under dynamic loading.

36 MATERIALS SCIENCE↗

Directional amorphization of covalently-bonded solids: A generalized deformation mechanism in extreme loading

Shock compression subjects materials to a unique regime of high quasi-hydrostatic pressure and coupled shear stresses for durations on the order of 1–10 nanoseconds for laser-driven loading of samples. There is, additionally, an attendant temperature increase due to the shock and the mechanisms of plastic deformation in metals whereby dislocations, twins, and phase transitions nucleate and propagate at velocities near the sound speed. Covalently bonded materials have, by virtue of the directionality of their bonds, great difficulty in responding by conventional plastic deformation to this extreme regime of shock compression. Here, we propose that the shear from shock compression induces amorphization, as observed in Si, Ge, B4C, SiC, and olivine ((Mg, Fe) 2 SO 4 ) and that this is a general deformation mechanism in a broad class of covalently bonded materials. The crystalline structure transforms to amorphous along regions of maximum shear stress, forming nanoscale bands, and thereby relaxing the shear component of the imposed shock stress. This process is usually preceded by the emission and propagation of a critical concentration of dislocations.

36 MATERIALS SCIENCE↗

Shock-induced amorphization in silicon carbide

While silicon carbide (SiC) has been predicted to undergo pressure-induced amorphization, the microstructural evidence of such a drastic phase change is absent as its brittleness usually prevents its successful recovery from high-pressure experiments. In this paper we report on the observation of amorphous SiC recovered from laser-ablation-driven shock compression with a peak stress of approximately 50 GPa. Transmission electron microscopy reveals that the amorphous regions are extremely localized, forming bands as narrow as a few nanometers. In addition to these amorphous bands, planar stacking faults are observed. Large-scale non-equilibrium molecular dynamic simulations elucidate the process and suggest that the planar stacking faults serve as the precursors to amorphization. Finally, our results suggest that the amorphous phase produced is a high-density form, which enhances its thermodynamical stability under the high pressures combined with the shear stresses generated by the uniaxial strain state in shock compression.

36 MATERIALS SCIENCE↗

Spall strength dependence on grain size and strain rate in tantalum

In this paper, we examine the effect of grain size on the dynamic failure tantalum during laser-shock compression and release and identify a significant effect of grain size on spall strength, which is opposite to the prediction of the Hall-Petch relationship because spall is primarily intergranular in both poly and nanocrystalline samples; thus, monocrystals have a higher spall strength than polycrystals, which, in turn, are stronger in tension than ultra-fine grain sized specimens. Post-shock characterization reveals ductile failure which evolves by void nucleation, growth, and coalescence. Whereas in the monocrystal the voids grow in the interior, nucleation is both intra and intergranular in the poly and ultra-fine-grained crystals. The fact that spall is primarily intergranular in both poly and nanocrystalline samples is strong evidence for higher growth rates of intergranular voids, which have a distinctly oblate spheroid shape in contrast with intragranular voids, which are more spherical. The length geometrically-necessary dislocations required to form a grain-boundary (intergranular) void is lower than that of grain-interior (intragranular) void with the same maximum diameter; thus, the energy required is lower. Consistent with prior literature and theory we also identify an increase with spall strength with strain rate from 6x10 6 to 5x10 7 s -1 . Molecular dynamics calculations agree with the experimental results and also predict grain-boundary separation in the spalling of polycrystals as well as an increase in spall strength with strain rate. Finally, an analytical model based on the kinetics of nucleation and growth of intra and intergranular voids and extending the Curran-Seaman-Shockey theory is applied which shows the competition between the two processes for polycrystals.

36 MATERIALS SCIENCE↗

High-velocity deformation of Al 0.3 CoCrFeNi high-entropy alloy: Remarkable resistance to shear failure

Here, the mechanical behavior of a single phase (fcc) Al 0.3 CoCrFeNi high-entropy alloy (HEA) was studied in the low and high strain-rate regimes. The combination of multiple strengthening mechanisms such as solid solution hardening, forest dislocation hardening, as well as mechanical twinning leads to a high work hardening rate, which is significantly larger than that for Al and is retained in the dynamic regime. The resistance to shear localization was studied by dynamically-loading hat-shaped specimens to induce forced shear localization. However, no adiabatic shear band could be observed. It is therefore proposed that the excellent strain hardening ability gives rise to remarkable resistance to shear localization, which makes this material an excellent candidate for penetration protection applications such as armors.

36 MATERIALS SCIENCE↗

Supersonic Dislocation Bursts in Silicon

Dislocations are the primary agents of permanent deformation in crystalline solids. Since the theoretical prediction of supersonic dislocations over half a century ago, there is a dearth of experimental evidence supporting their existence. Here we use non-equilibrium molecular dynamics simulations of shocked silicon to reveal transient supersonic partial dislocation motion at approximately 15 km/s, faster than any previous in-silico observation. Homogeneous dislocation nucleation occurs near the shock front and supersonic dislocation motion lasts just fractions of picoseconds before the dislocations catch the shock front and decelerate back to the elastic wave speed. Applying a modified analytical equation for dislocation evolution we successfully predict a dislocation density of 1.5 x 10(12) cm(-2) within the shocked volume, in agreement with the present simulations and realistic in regards to prior and on-going recovery experiments in silicon.

36 MATERIALS SCIENCE↗

Shock compression of [001] single crystal silicon

Silicon is ubiquitous in our advanced technological society, yet our current understanding of change to its mechanical response at extreme pressures and strain-rates is far from complete. This is due to its brittleness, making recovery experiments difficult. High-power, short-duration, laser-driven, shock compression and recovery experiments on [001] silicon (using impedance-matched momentum traps) unveiled remarkable structural changes observed by transmission electron microscopy. As laser energy increases, corresponding to an increase in peak shock pressure, the following plastic responses are are observed: surface cleavage along {111} planes, dislocations and stacking faults; bands of amorphized material initially forming on crystallographic orientations consistent with dislocation slip; and coarse regions of amorphized material. Molecular dynamics simulations approach equivalent length and time scales to laser experiments and reveal the evolution of shock-induced partial dislocations and their crucial role in the preliminary stages of amorphization. Furthermore, application of coupled hydrostatic and shear stresses produce amorphization below the hydrostatically determined critical melting pressure under dynamic shock compression.

36 MATERIALS SCIENCE↗

Probing the character of ultra-fast dislocations

Plasticity is often controlled by dislocation motion, which was first measured for low pressure, low strain rate conditions decades ago. However, many applications require knowledge of dislocation motion at high stress conditions where the data are sparse, and come from indirect measurements dominated by the effect of dislocation density rather than velocity. Here we make predictions based on atomistic simulations that form the basis for a new approach to measure dislocation velocities directly at extreme conditions using three steps: create prismatic dislocation loops in a near-surface region using nanoindentation, drive the dislocations with a shockwave, and use electron microscopy to determine how far the dislocations moved and thus their velocity at extreme stress and strain rate conditions. We report on atomistic simulations of tantalum that make detailed predictions of dislocation flow, and find that the approach is feasible and can uncover an exciting range of phenomena, such as transonic dislocations and a novel form of loop stretching. Furthermore, the simulated configuration enables a new class of experiments to probe average dislocation velocity at very high applied shear stress.

36 MATERIALS SCIENCE↗

Amorphization and nanocrystallization of silcon under shock compression

High-power, short-duration, laser-driven, shock compression and recovery experiments on [001] silicon unveiled remarkable structural changes above a pressure threshold. Two distinct amorphous regions were identified: (a) a bulk amorphous layer close to the surface and (b) amorphous bands initially aligned with {111} slip planes. Further increase of the laser energy leads to the re-crystallization of amorphous silicon into nanocrystals with high concentration of nano-twins. This amorphization is produced by the combined effect of high magnitude hydrostatic and shear stresses under dynamic shock compression. Shock-induced defects play a very important role in the onset of amorphization. Calculations of the free energy changes with pressure and shear, using the Patel-Cohen methodology, are in agreement with the experimental results. Molecular dynamics simulation corroborates the amorphization, showing that it is initiated by the nucleation and propagation of partial dislocations. As a result, the nucleation of amorphization is analyzed qualitatively by classical nucleation theory.

36 MATERIALS SCIENCE↗

Phase transformation in tantalum under extreme laser deformation

The structural and mechanical response of metals is intimately connected to phase transformations. For instance, the product of a phase transformation (martensite) is responsible for the extraordinary range of strength and toughness of steel, making it a versatile and important structural material. Although abundant in metals and alloys, the discovery of new phase transformations is not currently a common event and often requires a mix of experimentation, predictive computations, and luck. High-energy pulsed lasers enable the exploration of extreme pressures and temperatures, where such discoveries may lie. The formation of a hexagonal (omega) phase was observed in recovered monocrystalline body-centered cubic tantalum of four crystallographic orientations subjected to an extreme regime of pressure, temperature, and strain-rate. This was accomplished using high-energy pulsed lasers. The omega phase and twinning were identified by transmission electron microscopy at 70 GPa (determined by a corresponding VISAR experiment). It is proposed that the shear stresses generated by the uniaxial strain state of shock compression play an essential role in the transformation. In conclusion, molecular dynamics simulations show the transformation of small nodules from body-centered cubic to a hexagonal close-packed structure under the same stress state (pressure and shear).

36 MATERIALS SCIENCE↗

Plastic deformation in nanoindentation of tantalum: A new mechanism for prismatic loop formation

Here, the mechanisms of deformation under a nanoindentation in tantalum, chosen as a model body-centered cubic (bcc) metal, are identified and quantified. Molecular dynamics (MD) simulations and indentation experiments are conducted for [1 0 0], [1 1 0] and [1 1 1] normals to surface orientations. The simulated plastic deformation proceeds by the formation of nanotwins, which rapidly evolve into shear dislocation loops. It is shown through a dislocation analysis that an elementary twin (three layers) is energetically favorable for a diameter below ~7 nm, at which point a shear loop comprising a perfect dislocation is formed. MD simulations show that shear loops expand into the material by the advancement of their edge components. Simultaneously with this advancement, screw components of the loop cross-slip and generate a cylindrical surface. When opposite segments approach, they eventually cancel by virtue of the attraction between them, forming a quasi-circular prismatic loop composed of edge dislocation segments. This “lasso”-like mechanism by which a shear loop transitions to a prismatic loop is identified for both [0 0 1] and [1 1 1] indentations. The prismatic loops advance into the material along $\langle$1 1 1$\rangle$ directions, transporting material away from the nucleation site. Analytical calculations supplement MD and experimental observations, and provide a framework for the improved understanding of the evolution of plastic deformation under a nanoindenter. Dislocation densities under the indenter are estimated experimentally (~1.2 × 10 15 m -2 ), by MD (~7 × 10 15 m -2 ) and through an analytical calculation (2.6–19 × 10 15 m -2 ). Considering the assumptions and simplifications, this agreement is considered satisfactory. MD simulations also show expected changes in pile-up symmetry after unloading, compatible with crystal plasticity.

36 MATERIALS SCIENCE↗

Atomistic simulation of tantalum nanoindentation: Effects of indenter diameter, penetration velocity, and interatomic potentials on defect mechanisms and evolution

Nanoindentation simulations are a helpful complement to experiments. There is a dearth of nanoindentation simulations for bcc metals, partly due to the lack of computationally efficient and reliable interatomic potentials at large strains. For this study, we carry out indentation simulations for bcc tantalum using three different interatomic potentials and present the defect mechanisms responsible for the creation and expansion of the plastic deformation zone: twins are initially formed, giving rise to shear loop expansion and the formation of sequential prismatic loops. The calculated elastic constants as function of pressure as well as stacking fault energy surfaces explain the significant differences found in the defect structures generated for the three potentials investigated in this study. The simulations enable the quantification of total dislocation length and twinning fraction. The indenter velocity is varied and, as expected, the penetration depth for the first pop-in (defect emission) event shows a strain rate sensitivity m in the range of 0.037–0.055. The effect of indenter diameter on the first pop-in is discussed. A new intrinsic length-scale model is presented based on the profile of the residual indentation and geometrically necessary dislocation theory.

36 MATERIALS SCIENCE↗

Plastic deformation of a porous bcc metal containing nanometer sized voids

Nanoporous materials, can present an outstanding range of mechanical properties. Here both molecular dynamics and dislocation analysis were used to evaluate and quantify the evolution of plasticity in a porous Ta single crystal containing randomly placed voids with 3.3 nm radii and average initial porosity of 4.1%, when subjected to uniaxial compressive strain. Nanovoids act as effective sources for dislocation emission. Dislocation shear loops nucleate at the surface of the voids and expand by the advance of the edge component. The evolution of dislocation configuration and densities were predicted by the molecular dynamics calculations and successfully compared to an analysis based on Ashby’s concept of geometrically-necessary dislocations. Resolved shear stress calculations were performed for all bcc slip systems and used to identify the operating Burgers vectors in the dislocation loops. The temperature excursion during plastic deformation was used to estimate the mobile dislocation density which is found to be less than 10% of the total dislocation density.

36 MATERIALS SCIENCE↗

Laser shocking of materials: Toward the national ignition facility

In recent years a powerful experimental tool has been added to the arsenal at the disposal of the materials scientist investigating materials response at extreme regimes of strain rates, temperatures, and pressures: laser compression. In this paper, this technique has been applied successfully to mono-, poly-, and nanocrystalline metals and the results have been compared with predictions from analytical models and molecular dynamics simulations. Special flash x-ray radiography and flash x-ray diffraction, combined with laser shock propagation, are yielding the strength of metals at strain rates on the order of 10 7 –10 8 s -1 and resolving details of the kinetics of phase transitions. A puzzling result is that experiments, analysis, and simulations predict dislocation densities that are off by orders of magnitude. Finally, other surprises undoubtedly await us as we explore even higher pressure/strain rate/temperature regimes enabled by the National Ignition Facility.

36 MATERIALS SCIENCE↗