Michelle N. Banchy | Search NASA

NASA NTRSDate not supplied

CDISC Remote Design Method to Simulate Aircraft Interference Effects for the CATNLF Flight Test

The Crossflow Attenuated Natural Laminar Flow (CATNLF) flight test is an experimental evaluation of a laminar flow design approach that will be conducted on a small transonic wing-like model suspended from the Centerline Instrumented Pylon (CLIP) underneath an F-15 vehicle. The upcoming flight test is anticipated to provide experimental data that may be useful for transition prediction code calibrations or laminar flow computational studies. For the computational results to be reliable, relevant aerodynamics must be included in the simulations. It has been shown that the F-15 vehicle produces a notable aerodynamic influence on the CATNLF test article, and that removing the F-15 vehicle from the simulation significantly alters the laminar flow behavior. Because the F-15 vehicle is not a publicly-releasable geometry, if the CATNLF flight test dataset is to be widely used by the community, an alternative method to ensure that the CATNLF test article flight configuration aerodynamics is properly modeled is required. The objective of this research is to use the CDISC aerodynamic design tool to perform a remote design of a surface that would replicate the aerodynamic influence on the CATNLF test article. This new design approach, referred to as the Equivalent Loading via Interference Surface Effects (ELISE), is presented in this paper, including the details on the design setup and results. The ELISE design successfully reproduced the F-15 influence on the CATNLF test article, with predicted transition location within an average of 4% chord of the full flight configuration. An off-design assessment is included for small perturbations in Mach and sideslip angle that suggest the ELISE design can cover a reasonable range of expected flight conditions with the same geometry. This paper is intended to explain the design approach, as well as show results that can be expected when utilizing the ELISE design method.

CDISC↗

NASA NTRSDate not supplied

Progress Towards the Design of a Natural Laminar Flow Wing for a Low-Boom Concept using CDISC

The X-59 is being developed to evaluate the ability to reduce sonic boom loudness to acceptable levels, with the ultimate goal of enabling supersonic flight overland. If successful, one of the future research challenges will be focused on reducing fuel burn. In this paper, Natural Laminar Flow (NLF) is proposed as a technology to decrease fuel burn for a low-boom configuration. This will require an evaluation of the compatibility of NLF wings for a low-boom configuration. As a first step towards this goal, the CATNLF method was employed using the CDISC design module to perform NLF design on an isolated wing from a low-boom configuration. The results show that the NLF wing features laminar flow over 46% of the wing upper surface, providing a potential 8.3 drag count reduction relative to the design with no laminar flow. Off-design analyses were additionally performed to evaluate the performance of the NLF wing for changes in angle of attack and Mach number. The results showed that the NLF wing offers a performance benefit over the entire range of off-design conditions considered, with most of the laminar flow maintained for near cruise conditions. Future work will consider the full configuration, which will enable an assessment of the impact of the NLF wing design on sonic boom loudness. Additionally, attachment line transition will be addressed, which was predicted to result in a loss of laminar flow on the inboard 50% span for this work. Finally, future research will focus on developing a method for effectively choosing the frequency-beta pairs used for the stability analysis to improve transition prediction and provide a more accurate estimate of the performance benefit.

Supersonic↗

NASA NTRSDate not supplied

Transonic Cruise Slotted Wing Design for Commercial Transport Aircraft using CDISC

A knowledge-based aerodynamic design method, CDISC, has been extended to enable the computational design of transonic cruise slotted wings for commercial transport aircraft. The cruise slotted wing is a multielement wing concept with a forward main element and an aft flap element, separated to form an intermediate slot. This slot favorably redirects airflow from the main element lower surface toward the low-momentum, upper-surface boundary layer of the flap. Relative to the supercritical wing, the cruise slotted wing enables greater aft loading that helps to reduce shock strength and transonic pressure drag. The cruise slotted wing may be considered a passive drag reduction technology with potential fuel-burn savings and increased vehicle range for next-generation aircraft. The current paper seeks to quantify the drag-saving benefits of cruise slotted wing technology in application to single-aisle commercial transport aircraft. A series of multielement design constraints were developed within CDISC for the design of a partial-span, cruise slotted wing for a Mach-0.8 variant of the Common Research Model. To mitigate the skin-friction drag penalty associated with cruise slotted wings, the design features a flap with natural laminar flow over approximately 75% of the flap surface area. Cruise drag estimates from the NASA USM3D-ME flow solver between a supercritical wing and the partial-span, cruise slotted wing design were within one drag count. Near-cruise, off-design analyses showed limited laminar-flow sensitivity to angle of attack and a more gradual drag rise compared to a supercritical wing. Based on this observed benefit, future work is motivated to design a cruise slotted wing with laminar flow on both wing elements to achieve a significant reduction in cruise drag while delaying drag divergence.

CDISC↗

NASA NTRSDate not supplied

History and Status of the CDISC Aerodynamic Design Method

This paper will review the development and application of the CDISC aerodynamic design method that began in the early 1980s and continues in active use today. The method uses an iterative, knowledge-based approach that has been coupled with numerous flow solvers utilizing a variety of grid types and levels of flow physics. It has been applied to configurations varying in complexity from 2-D airfoils to full 3-D aircraft at flow conditions ranging from low-speed, high-lift to supersonic cruise. The knowledge-based approach provides a very rapid design process, with designs typically completed in approximately 1-2x the time required for an initial converged analysis of the baseline. The evolution of the method as it tracked the expansive growth of grid and flow solver technology, along with some major applications over 5 decades, are given, followed by a description of the philosophy and process used in design. Finally, an example of its use in a preliminary design environment is given.

CDISC↗

NASA NTRSDate not supplied

History and Status of the CDISC Aerodynamic Design Method

This paper will review the development and application of the CDISC aerodynamic design method that began in the early 1980s and continues in active use today. The method uses an iterative, knowledge-based approach that has been coupled with numerous flow solvers utilizing a variety of grid types and levels of flow physics. It has been applied to configurations varying in complexity from 2-D airfoils to full 3-D aircraft at flow conditions ranging from low-speed, high-lift to supersonic cruise. The knowledge-based approach provides a very rapid design process, with designs typically completed in approximately 1-2x the time required for an initial converged analysis of the baseline. The evolution of the method as it tracked the expansive growth of grid and flow solver technology, along with some major applications over 5 decades, are given, followed by a description of the philosophy and process used in design. Finally, an example of its use in a preliminary design environment is given.

CDISC↗