Search NASA⌕ Search

Engineering topics

Miller, Gregory K

Publications and source records attributed to Miller, Gregory K.

Modeling Thermal and Stress Behavior of the Fuel-clad Interface in Monolithic Fuel Mini-plates

As part of the Global Threat Reduction Initiative, a fuel development and qualification program is in process with the objective of qualifying very high density low enriched uranium fuel that will enable the conversion of high performance research reactors with operational requirements beyond those supported with currently available low enriched uranium fuels. The high density of the fuel is achieved by replacing the fuel meat with a single monolithic low enriched uranium-molybdenum fuel foil. Doing so creates differences in the mechanical and structural characteristics of the fuel plate because of the planar interface created by the fuel foil and cladding. Furthermore, the monolithic fuel meat will dominate the structural properties of the fuel plate rather than the aluminum matrix, which is characteristic of dispersion fuel types. Understanding the integrity and behavior of the fuel-clad interface during irradiation is of great importance for qualification of the new fuel, but can be somewhat challenging to determine with a single technique. Efforts aimed at addressing this problem are underway within the fuel development and qualification program, comprised of modeling, as-fabricated plate characterization, and post-irradiation examination. An initial finite element analysis model has been developed to investigate worst-case scenarios for the basic monolithic fuel plate structure, using typical mini-plate irradiation conditions in the Advanced Test Reactor. Initial analysis shows that the stress normal to the fuel-clad interface dominates during irradiation, and that the presence of small, rounded delaminations at the interface is not of great concern. However, larger and/or fuel-clad delaminations with sharp corners can create areas of concern, as maximum principal cladding stress, strain, displacement, and peak fuel temperature are all significantly increased. Furthermore, stresses resulting from temperature gradients that cause the plate to bow or buckle in an unconstrained fuel plate configuration is greatly enhanced in a constrained fuel plate configuration. The sensitivities of the model and input parameters are discussed, along with some overlap of initial experimental observations using as-fabricated plate characterization and post-irradiation examination.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Calculating Failure Probabilities for TRISO-coated Fuel Particles using an Integral Formulation

The fundamental design for a gas-cooled reactor relies on the safe behavior of the coated particle fuel. The coating layers surrounding the fuel kernels in these spherical particles, termed the TRISO coating, act as a pressure vessel that retains fission products. The quality of the fuel reflects the number of particle failures that occur during reactor operation, where failed particles become a source for fission products that can then diffuse through the fuel element matrix. The failure probability for any batch of particles, which has traditionally been calculated using the Monte Carlo method, depends on statistical variations in design parameters and on variations in the strengths of coating layers among particles in the batch. An alternative approach to calculating failure probabilities is developed herein that uses direct numerical integration of a failure probability integral. Because this is a multiple integral where the statistically varying parameters become integration variables, a fast numerical integration approach is also developed. In sample cases analyzed involving multiple failure mechanisms, results from the integration methods agree closely with Monte Carlo results. Additionally, the fast integration approach, particularly, is shown to significantly improve efficiency of failure probability calculations. These integration methods have been implemented in the PARFUME fuel performance code along with the Monte Carlo method, where each serves to verify accuracy of the others.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

PARFUME Theory and Model basis Report

The success of gas reactors depends upon the safety and quality of the coated particle fuel. The fuel performance modeling code PARFUME simulates the mechanical, thermal and physico-chemical behavior of fuel particles during irradiation. This report documents the theory and material properties behind vari¬ous capabilities of the code, which include: 1) various options for calculating CO production and fission product gas release, 2) an analytical solution for stresses in the coating layers that accounts for irradiation-induced creep and swelling of the pyrocarbon layers, 3) a thermal model that calculates a time-dependent temperature profile through a pebble bed sphere or a prismatic block core, as well as through the layers of each analyzed particle, 4) simulation of multi-dimensional particle behavior associated with cracking in the IPyC layer, partial debonding of the IPyC from the SiC, particle asphericity, and kernel migration (or amoeba effect), 5) two independent methods for determining particle failure probabilities, 6) a model for calculating release-to-birth (R/B) ratios of gaseous fission products that accounts for particle failures and uranium contamination in the fuel matrix, and 7) the evaluation of an accident condition, where a particle experiences a sudden change in temperature following a period of normal irradiation. The accident condi¬tion entails diffusion of fission products through the particle coating layers and through the fuel matrix to the coolant boundary. This document represents the initial version of the PARFUME Theory and Model Basis Report. More detailed descriptions will be provided in future revisions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

New Mechanical Model for the Transmutation Fuel Performance Code

A new mechanical model has been developed for implementation into the TRU fuel performance code. The new model differs from the existing FRAPCON 3 model, which it is intended to replace, in that it will include structural deformations (elasticity, plasticity, and creep) of the fuel. Also, the plasticity algorithm is based on the “plastic strain–total strain” approach, which should allow for more rapid and assured convergence. The model treats three situations relative to interaction between the fuel and cladding: (1) an open gap between the fuel and cladding, such that there is no contact, (2) contact between the fuel and cladding where the contact pressure is below a threshold value, such that axial slippage occurs at the interface, and (3) contact between the fuel and cladding where the contact pressure is above a threshold value, such that axial slippage is prevented at the interface. The first stage of development of the model included only the fuel. In this stage, results obtained from the model were compared with those obtained from finite element analysis using ABAQUS on a problem involving elastic, plastic, and thermal strains. Results from the two analyses showed essentially exact agreement through both loading and unloading of the fuel. After the cladding and fuel/clad contact were added, the model demonstrated expected behavior through all potential phases of fuel/clad interaction, and convergence was achieved without difficulty in all plastic analysis performed. The code is currently in stand alone form. Prior to implementation into the TRU fuel performance code, creep strains will have to be added to the model. The model will also have to be verified against an ABAQUS analysis that involves contact between the fuel and cladding.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗