Search NASA⌕ Search

Engineering topics

Millot, M.

Publications and source records attributed to Millot, M..

54 records · Page 3

Measurement of the sound speed in dense fluid deuterium along the cryogenic liquid Hugoniot

Many experimental studies, spanning several decades of research and using various dynamic compression schemes, have been conducted to investigate cryogenic liquid deuterium under strong shock compression. The consensus emerging from these studies is that of a progressive dissociation of the D 2 molecules into an electrically conducting, atomic plasma, when subjected to shock pressures exceeding ~50 GPa. While state-of-the-art numerical simulations based on density-functional-theory or quantum Monte-Carlo techniques capture this behavior quite well, subtle differences subsist between these simulations and the available experimental data regarding the pressure-density compressibility. Here, leveraging a recently developed analysis method for high-resolution Doppler interferometric velocity data, we present Eulerian sound speed measurements in compressed deuterium to shock pressures between 50 and 200 GPa. These results, extracted from laser-driven shockwave experiments, are found to agree with several of the most accurate equation of state models for deuterium at those conditions up to ~150 GPa. However, the data indicate that these models fail to reproduce the experimentally observed sound speed at higher pressures, approaching 200 GPa. In particular, we unveil a discrepancy between the experimental results and the equation of state model that is most commonly used in inertial confinement fusion at the National Ignition Facility.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Energy transfer between lasers in low-gas-fill-density hohlraums

We investigate cross-beam energy transfer (CBET), where power is transferred from one laser beam to another via a shared ion acoustic wave in hohlraums with low-gas-fill density as a tool for late-time symmetry control for long-pulse (greater than 10 ns) inertial confinement fusion (ICF) and laboratory astrophysics experiments. We show that the radiation drive symmetry can be controlled and accurately predicted during the foot of the pulse (until the rise to peak power), which is important for mitigating areal density variations in the compressed fuel in ICF implosions. We also show that the effective inner-beam drive after CBET is much greater than observed in previous high-gas-filled-hohlraum experiments, which is thought to be a result of less inverse bremsstrahlung absorption of the incident laser light and reduced (by more than 10 times) stimulated Raman scattering (and Langmuir wave heating). With the inferred level of inner-beam drive after transfer, we estimate that more than 1.25 times larger plastic capsules could be fielded in this platform with sufficient laser-beam propagation to the waist of the hohlraum. We also estimate that a full-scale plastic capsule, 1100 μm in capsule radius, would require ~1 – 2 Å of 1 ω wavelength separation between the outer and inner beams to achieve a symmetric implosion in this platform.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Beryllium capsule implosions at a case-to-capsule ratio of 3.7 on the National Ignition Facility

Beryllium is a candidate ablator material for indirect-drive inertial confinement fusion experiments, motivated by its high mass ablation rate, which is advantageous for implosion coupling efficiency and stabilization of the ablation-front instability growth. In this paper, we present new data on the shock propagation, in-flight shape, and hot spot self-emission shape from gas-filled capsules that demonstrate the feasibility of predictable, symmetric, controllable beryllium implosions at a case-to-capsule ratio of 3.7. The implosions are round (Legendre mode 2 amplitude ≲5%) at an inner beam power and the energy fraction of 26%–28% of the total, indicating that larger beryllium capsules could be driven symmetrically using the National Ignition Facility.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High-Performance Indirect-Drive Cryogenic Implosions at High Adiabat on the National Ignition Facility

To reach the pressures and densities required for ignition, it may be necessary to develop an approach to design that makes it easier for simulations to guide experiments. Here, we report on a new short-pulse inertial confinement fusion platform that is specifically designed to be more predictable. Furthermore, the platform has demonstrated 99%+0.5% laser coupling into the hohlraum, high implosion velocity (411 km/s), high hotspot pressure (220+60 Gbar), and high cold fuel areal density compression ratio (>400), while maintaining controlled implosion symmetry, providing a promising new physics platform to study ignition physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Thermodynamic properties of MgSiO 3 at super-Earth mantle conditions

Recent discoveries of terrestrial exoplanets distant from our solar system motivate laboratory experiments that provide insight into their formation and thermal evolution. Using laser-driven shock wave experiments, we constrain high-temperature and high-pressure adiabats and the equation of state of MgSiO 3 ,a dominant mantle constituent of terrestrial exoplanets. Critical to the development of a habitable exoplanet is the early thermal history, specifically the formation and freezing of the magma ocean and its role in enabling convection in the mantle and core. We measure the adiabatic sound speed and constrain the melt transition along the Hugoniot and find that the adiabats and melt boundary of silicate magmas are shallower than predicted. In conclusion, this suggests that small changes in the temperature of a super-Earth mantle would result in rapid melting and solidification of nearly the entire mantle.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fusion Energy Output Greater than the Kinetic Energy of an Imploding Shell at the National Ignition Facility

A series of cryogenic, layered deuterium-tritium (DT) implosions have produced, for the first time, fusion energy output twice the peak kinetic energy of the imploding shell. These experiments at the National Ignition Facility utilized high density carbon ablators with a three-shock laser pulse (1.5 MJ in 7.5 ns) to irradiate low gas-filled ( 0.3 mg / cc of helium) bare depleted uranium hohlraums, resulting in a peak hohlraum radiative temperature ~ 290 eV . The imploding shell, composed of the nonablated high density carbon and the DT cryogenic layer, is, thus, driven to velocity on the order of 380 km / s resulting in a peak kinetic energy of ~ 21 kJ , which once stagnated produced a total DT neutron yield of 1.9 × 10 16 (shot N170827) corresponding to an output fusion energy of 54 kJ. Time dependent low mode asymmetries that limited further progress of implosions have now been controlled, leading to an increased compression of the hot spot. Finally, it resulted in hot spot areal density ( ρr ~ 0.3 g / cm 2 ) and stagnation pressure ( ~ 360 Gbar ) never before achieved in a laboratory experiment.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A near one-dimensional indirectly driven implosion at convergence ratio 30

Inertial confinement fusion cryogenic-layered implosions at the National Ignition Facility, while successfully demonstrating self-heating due to alpha-particle deposition, have fallen short of the performance predicted by one-dimensional (1D) multi-physics implosion simulations. The current understanding, from experimental evidence as well as simulations, suggests that engineering features such as the capsule tent and fill tube, as well as time-dependent low-mode asymmetry, are to blame for the lack of agreement. A short series of experiments designed specifically to avoid these degradations to the implosion are described here in order to understand if, once they are removed, a high-convergence cryogenic-layered deuterium-tritium implosion can achieve the 1D simulated performance. The result is a cryogenic layered implosion, round at stagnation, that matches closely the performance predicted by 1D simulations. This agreement can then be exploited to examine the sensitivity of approximations in the model to the constraints imposed by the data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measuring the shock impedance mismatch between high-density carbon and deuterium at the National Ignition Facility

Fine-grained diamond, or high-density carbon (HDC), is being used as an ablator for inertial confinement fusion (ICF) research at the National Ignition Facility (NIF). Accurate equation of state (EOS) knowledge over a wide range of phase space is critical in the design and analysis of integrated ICF experiments. Here in this paper, we report shock and release measurements of the shock impedance mismatch between HDC and liquid deuterium conducted during shock-timing experiments having a first shock in the ablator ranging between 8 and 14 Mbar. Using ultrafast Doppler imaging velocimetry to track the leading shock front, we characterize the shock velocity discontinuity upon the arrival of the shock at the HDC/liquid deuterium interface. Comparing the experimental data with tabular EOS models used to simulate integrated ICF experiments indicates the need for an improved multiphase EOS model for HDC in order to achieve a significant increase in neutron yield in indirect-driven ICF implosions with HDC ablators.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Shock equation of state of LiH 6 to 1.1 TPa

Using laser-generated shock waves, we have measured pressure, density, and temperature of LiH on the principal Hugoniot between 260 and 1100 GPa (2.6–11 Mbar) and on a second-shock Hugoniot up to 1400 GPa to near fivefold compression, extending the maximum pressure reached in non-nuclear experiments by a factor of two. Here, we observe the onset of metal-like reflectivity consistent with temperature-induced ionization of the Li 2s electron, and no sign of additional changes in ionization up to the maximum pressure. Our measurements are in good agreement with gas gun, Z-machine, and underground test data and are accurately described by quantum molecular dynamics simulations. The results confirm the validity of equation of state models built on an average-atom description of the electron-thermal contribution to the free energy and a density-dependent Grüneisen parameter to describe shock response of LiH over this pressure range.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Examining the radiation drive asymmetries present in the high foot series of implosion experiments at the National Ignition Facility

This paper details and examines the origins of radiation drive asymmetries present during the initial High Foot implosion experiments. Such asymmetries are expected to reduce the stagnation pressure and the resulting yield of these experiments by several times. Analysis of reemission and dual axis shock timing experiments indicates that a flux asymmetry, with a P2/P0 amplitude that varies from -10 to -5 %, is present during the first shock of the implosion. This first shock asymmetry can be corrected through adjustments to the laser cone fraction. A thin shell model and more detailed radiation hydrodynamic calculations indicate that an additional negative P2/P0 asymmetry during the second or portions of the third shock is required to reach the observed amount of asymmetry in the shape of the ablator at peak implosion velocity. In conjunction with symmetry data from the x-ray self emission produced at stagnation, these models also indicate that after the initially negative P2/P0 flux asymmetry, the capsule experiences a positive P2/P0 flux asymmetry that develops at or before ~2 ns into the peak of the laser power. Here, direct evidence for this inference, using measurements of the x-ray emission produced by the lasers irradiating the hohlraum, is presented. This data indicates that the reduction in the transmitted inner laser cone energy results from impeded propagation through the plasma associated with the ablation of the capsule target. This paper also correlates measurements of the outer cone laser deposition location with variations in the observed x-ray self emission shape from experiments conducted with nominally the same input conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Absolute calibration of the OMEGA streaked optical pyrometer for temperature measurements of compressed materials

Experiments in high-energy-density physics often use optical pyrometry to determine temperatures of dynamically compressed materials. In combination with simultaneous shock-velocity and optical-reflectivity measurements using velocity interferometry, these experiments provide accurate equation-of-state data at extreme pressures (P > 1 Mbar) and temperatures (T > 0.5 eV). This paper reports on the absolute calibration of the streaked optical pyrometer (SOP) at the Omega Laser Facility. The wavelength-dependent system response was determined by measuring the optical emission from a National Institute of Standards and Technology–traceable tungsten-filament lamp through various narrowband (40 nm-wide) filters. The integrated signal over the SOP’s ~250-nm operating range is then related to that of a blackbody radiator using the calibrated response. We present a simple closed-form equation for the brightness temperature as a function of streak-camera signal derived from this calibration. As a result, error estimates indicate that brightness temperature can be inferred to a precision of <5%.

36 MATERIALS SCIENCE↗

Equation of state, adiabatic sound speed, and Gruneisen coefficient of boron carbide along the principal Hugoniot to 700 GPa

We describe a new equation of state (EOS) experimental technique that enables the study of thermodynamic derivatives into the TPa regime and apply it to boron carbide (B4C). The data presented here are the first principal Hugoniot sound speed measurements reported using a laser-driven shock platform, providing a new means to explore the high-pressure off-Hugoniot response of opaque materials. Furthermore, the extended B4C Hugoniot suggests the presence of a new high-pressure phase, as recently predicted by molecular dynamics simulations, adding to the complexity of the existing phase diagram.

36 MATERIALS SCIENCE↗

Ultrabright x-ray laser scattering for dynamic warm dense matter physics

In megabar shock waves, materials compress and undergo a phase transition to a dense charged-particle system that is dominated by strong correlations and quantum effects. This complex state, known as warm dense matter, exists in planetary interiors and many laboratory experiments (for example, during high-power laser interactions with solids or the compression phase of inertial confinement fusion implosions). Here, we apply record peak brightness X-rays at the Linac Coherent Light Source to resolve ionic interactions at atomic (ångström) scale lengths and to determine their physical properties. Our in situ measurements characterize the compressed lattice and resolve the transition to warm dense matter, demonstrating that short-range repulsion between ions must be accounted for to obtain accurate structure factor and equation of state data. Additionally, the unique properties of the X-ray laser provide plasmon spectra that yield the temperature and density with unprecedented precision at micrometre-scale resolution in dynamic compression experiments.

laser-produced plasmas↗

FY14 LLNL OMEGA Experimental Programs

In FY14, LLNL’s High-Energy-Density Physics (HED) and Indirect Drive Inertial Confinement Fusion (ICF-ID) programs conducted several campaigns on the OMEGA laser system and on the EP laser system, as well as campaigns that used the OMEGA and EP beams jointly. Overall these LLNL programs led 324 target shots in FY14, with 246 shots using just the OMEGA laser system, 62 shots using just the EP laser system, and 16 Joint shots using Omega and EP together. Approximately 31% of the total number of shots (62 OMEGA shots, 42 EP shots) shots supported the Indirect Drive Inertial Confinement Fusion Campaign (ICF-ID). The remaining 69% (200 OMEGA shots and 36 EP shots, including the 16 Joint shots) were dedicated to experiments for High- Energy-Density Physics (HED). Highlights of the various HED and ICF campaigns are summarized in the following reports.

36 MATERIALS SCIENCE↗

Thermodynamic properties and neutron diffraction studies of silver ferrite AgFeO2

We present thermodynamic and neutron scattering data on silver ferrite AgFeO2. The data imply strong magnetic frustration /TN ~ 10 and magnetic ordering takes place via two successive phase transitions at 2 = 7 K and 1 = 16 K. At T < T2, two metamagnetic phase transitions at B1 ~ 14 T and B2 ~ 30 T can be identified through the change of slope in the magnetization curve measured up to 53 T. These transitions roughly correspond to 1/8 and 1/4 of the saturation magnetizations. Unlike in the classical delafossite CuFeO2, the wave vector of the magnetic structure both at T < T2 and at T2 < T < T1 is independent of temperature.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗