Increased compression in HDC-based ablator implosions using modified drive profile
Not Available
Engineering topics
Publications and source records attributed to Milovich, J..
Not Available
Inertial confinement fusion ignition requires high inflight shell velocity, good energy coupling between the hotspot and shell, and high areal density at peak compression. Three-dimensional asymmetries caused by imperfections in the drive symmetry or target can grow and damage the coupling and confinement. Recent high-yield experiments have shown that low-mode asymmetries are a key degradation mechanism and contribute to variability. Here we show the experimental signatures and impacts of asymmetry change with increasing implosion yield given the same initial cause. This letter has implications for improving robustness to a key degradation in ignition experiments.
Here, this manuscript examines the correlations between the hot-spot velocity (an observable signature of residual kinetic energy), low-mode implosion asymmetries, and burn amplification in inertial confinement fusion implosions on the National Ignition Facility (NIF). Using a combination of two-dimensional axis-symmetric and three-dimensional radiation-hydrodynamic simulations coupled to neutronics, we find that for typical NIF implosions, the stagnation asymmetry multiplies the observed hot-spot velocity anywhere from 80% to 120%, while burn amplification always increases it. Additionally, we find stagnation asymmetry typically deflects the observed hot-spot flow. The two mechanisms (low-mode implosion asymmetries and burn amplification) can be decoupled, and application of a simple model to a database of cryogenic implosions on the NIF infers the total hot-spot velocity amplification. This finding modifies the interpretation of data collected from inertial confinement fusion experiments and impacts the magnitude and origin of low-mode asymmetries.
A recent experiment conducted on the National Ignition Facility (NIF) described in the study by Abu-Shawareb et al. achieved a fusion yield output of 1.3 MJ from ~ 220 kJ of x-ray energy absorbed by the capsule, demonstrating remarkable progress in the field of laser driven inertial confinement fusion. In the study by A. R. Christopherson [“Effects of charged particle heating on the hydrodynamics of inertially confined plasmas,” Ph.D. thesis (2020)], the plasma conditions needed to claim the onset of ignition and burn propagation were outlined and multiple criterion were provided to assess progress in inertial fusion experiments. In this work, we modify the metrics from A. R. Christopherson to accurately calculate performance metrics for indirect-drive experiments on the NIF. We also show that performance metric trends observed in NIF data are consistent with theory and simulations. This analysis indicates that all the identified criterion for ignition and burn propagation have been exceeded by experiment 210 808.
Inertial confinement fusion implosions must achieve high in-flight shell velocity, sufficient energy coupling between the hot spot and imploding shell, and high areal density ( ρ R = ∫ ρ d r ) at stagnation. Asymmetries in ρ R degrade the coupling of shell kinetic energy to the hot spot and reduce the confinement of that energy. In this study, we present the first evidence that nonuniformity in the ablator shell thickness ( ~ 0.5 % of the total thickness) in high-density carbon experiments is a significant cause for observed 3D ρ R asymmetries at the National Ignition Facility. These shell-thickness nonuniformities have significantly impacted some recent experiments leading to ρ R asymmetries on the order of ~ 25 % of the average ρ R and hot spot velocities of ~ 100 km / s . This work reveals the origin of a significant implosion performance degradation in ignition experiments and places stringent new requirements on capsule thickness metrology and symmetry.
Experiments on the National Ignition Facility (NIF) to study hohlraums lined with a 20-mg/cc 400-μm-thick Ta 2 O 5 aerogel at full scale (hohlraum diameter = 6.72 mm) are reported. Driven with a 1.6-MJ, 450-TW laser pulse, the performance of the foam liner is diagnosed using implosion hot-spot symmetry measurements of the high-density carbon (HDC) capsule and measurement of inner beam propagation through a thin-wall 8-μm Au window in the hohlraum. Results show an improved capsule performance due to laser energy deposition further inside the hohlraum, leading to a modest increase in x-ray drive and reduced preheat due to changes in the x-ray spectrum when the foam liner is included. In addition, the outer cone bubble uniformity is improved, but the predicted improvement in inner beam propagation to improve symmetry control is not realized for this foam thickness and density.
Plasma jets, such as γ-ray burst jets, Herbig–Haro jets, μ-quasar jets, and active galactic nuclei jets, are found throughout the universe [S. Mendoza et al., Rev. Mex. Astron. Astrofis. 41, 453 (2005)]. Plasma jets are also present in indirect drive inertial confinement fusion experiments originating from the capsule's fill tube and occasionally from divots and voids in the capsules, particles on the exterior of the capsule, or from the tent holding the capsule in the target. This paper looks at two different gas-filled capsule implosions containing a plasma jet resulting from a capsule fill tube and fill channel, both of which utilized high density carbon ablators. Two models were developed, a drag and a snowplow model, which use the time-dependent motion of the injected mass through the hotspot to estimate the mass injected into the hotspot from the fill tube and channel, arriving at an average injected mass of ~84.5 ± 25.5 ng for the first experiment and 91 ± 20 ng for the second experiment. Furthermore, unlike previous methods to estimate fill tube injected mass, these techniques do not assume that the mixed mass is in thermal equilibrium with the hotspot or that the x-ray emission is only coming from within the hotspot itself. This paper also discusses the features seen in these experiments which include limb brightening in the shell for undoped ablators and flattening in the ablator from shadowing by the fill tube.
In this paper, we report on eight, indirect-drive, deuterium–tritium-layered, inertial-confinement-fusion experiments at the National Ignition Facility to determine the largest capsule that can be driven symmetrically without relying on cross-beam energy transfer or advanced Hohlraum designs. Targets with inner radii of up to 1050 μm exhibited controllable P 2 symmetry, while larger capsules suffered from diminished equatorial drive. Reducing the Hohlraum gas-fill-density from 0.45 mg/cm 3 to 0.3 mg/cm 3 did not result in a favorable shift of P 2 amplitude as observed in preceding tuning experiments. Reducing the laser-entrance-hole diameter from 4 mm to 3.64 mm decreased polar radiation losses as expected, resulting in an oblate symmetry. The experiments exhibited the expected performance benefit from increased experimental scale, with yields at a fixed implosion velocity roughly following the predicted 1D dependence. With an inner radius of 1050 μm and a case-to-capsule-ratio of 3.0, experiment N181104 is the lowest implosion-velocity experiment to exceed a total neutron yield of 10 16 .
Here, we present a subgrid model for laser propagation in a subcritical foam. Our model describes the expansion of laser-irradiated foam elements that are below the resolution of the simulation grid and predicts the plasma conditions that result from burning down the foam. Our model can be included as a module within a larger multiphysics code, and we have implemented it within the code pF3D, which is used for simulating a laser-plasma interaction. The model predicts a reduced propagation velocity for a laser through a subcritical foam compared to simulating that foam as a homogeneous gas. This is attributed to the laser energy that goes into burning down the foam microstructure. We compare our model against experimental data by simulating a 2 mg/cc SiO 2 foam shot performed at the Janus laser facility at the Lawrence Livermore National Laboratory. pF3D simulations with the foam model predict hot ion temperatures. This leads to a reduction in the level of stimulated Brillouin scattering (SBS), bringing the simulated level of SBS into agreement with the data. Intensity fluctuations at the foam front due to laser speckles and refraction result in ion temperature fluctuations when the foam burns down. These drive long-lived electron density fluctuations on scales that are large compared to the pore size.
The implosion efficiency in inertial confinement fusion depends on the degree of stagnated fuel compression, density uniformity, sphericity, and minimum residual kinetic energy achieved. Compton scattering-mediated 50–200 keV x-ray radiographs of indirect-drive cryogenic implosions at the National Ignition Facility capture the dynamic evolution of the fuel as it goes through peak compression, revealing low-mode 3D nonuniformities and thicker fuel with lower peak density than simulated. By differencing two radiographs taken at different times during the same implosion, we also measure the residual kinetic energy not transferred to the hot spot and quantify its impact on the implosion performance.
We present results for the largest diamond capsule implosions driven symmetrically on the National Ignition Facility (NIF) (inner radius of ~1050 μm) without the use of cross beam transfer in cylindrical Hohlraums. We show that the methodology of designing Hohlraum parameters in a semi-empirical way using an extensive database resulted in a round implosion. In addition, we show that the radiation flux symmetry is well controlled during the foot of the pulse and that swings in P2 symmetry between the inflight dense shell and hot spot are within ±4 μm and that swings around peak compression are also within the symmetry specification of ±4 μm. We observed a stronger dependence of symmetry on the capsule scale than previously observed and also observed enhanced inner beam propagation for experiments using a gas fill density of 0.3 mg/cm 3 and 1000 μm inner radius capsules. We have observed sufficient symmetry and mass remaining at near full NIF power and energy, up to 480 TW and 1.9 MJ, with little laser–plasma interactions (low laser backscattered light) and predict that this design could support extended NIF energy of up to 2.1 MJ.
Hydrodynamic instabilities and asymmetries are a major obstacle in the quest to achieve ignition at the National Ignition Facility (NIF) as they cause pre-existing capsule perturbations to grow and ultimately quench the fusion burn in experiments. This paper reviews the development of two new experimental techniques to measure high-mode instabilities and low-mode asymmetries in the deceleration phase of indirect drive inertial confinement fusion implosions. In the first innovative technique, self-emission from the hot spot was enhanced with an argon dopant to “self-backlight” the shell in-flight, imaging the perturbations in the shell near peak velocity. Experiments with pre-imposed two-dimensional perturbations showed hydrodynamic instability growth of up to 7000× in areal density. These experiments discovered unexpected three-dimensional structures originating from the capsule support structures. These new 3-D structures became one of the primary concerns for the indirect drive ICF program that requires their origin to be understood and their impact mitigated. In a second complementary technique, the inner surface of the decelerating shell was visualized in implosions using x-ray emission of a high-Z dopant added to the inner surface of the capsule. With this technique, low mode asymmetry and high mode perturbations, including perturbations seeded by the gas fill tube and capsule support structure, were quantified near peak compression. Using this doping method, the role of perturbations and radiative losses from high atomic number materials on neutron yield was quantified.
During the first few hundred picoseconds of indirect drive for inertial confinement fusion on the National Ignition Facility, x-ray spots formed on the hohlraum wall when the drive beams cast shadows of the fuel fill-tube on the capsule surface. Differential ablation at the shadow boundaries seeds perturbations which are hydrodynamically unstable under subsequent acceleration and can grow to impact capsule performance. Furthermore, we have characterized this shadow imprint mechanism and demonstrated two techniques to mitigate against it using (i) a reduced diameter fuel fill-tube, and (ii) a pre-pulse to blow down the fill-tube before the shadow forming x-ray spots from the main outer drive beams develop.
Hydrodynamic instability growth of capsule support membranes (or “tents”) has been recognized as one of the major contributors to the performance degradation in high-compression plastic capsule implosions at the National Ignition Facility (NIF). The capsules were supported by tents because the nominal 10-μm diameter fill tubes were not strong enough to support capsules by themselves in indirect-drive implosions on NIF. After it was recognized that the tents had a significant impact of implosion's stability, new alternative support methods were investigated. While some of these methods completely eliminated tent, other concepts still used tents, but concentrated on mitigating their impact. The tent-less methods included “fishing pole” reinforced fill tubes, cantilevered fill tubes, and thin-wire “tetra cage” supports. In the “fishing pole” concept, a 10-μm fill tube was inserted inside 30-μm fill tube for extra support with the connection point located 300 μm away from the capsule surface. The cantilevered fill tubes were supported by 12-μm thick SiC rods, offset by up to 300 μm from the capsule surfaces. In the “tetra-cage” concept, 2.5-μm thick wires (carbon nanotube yarns) were used to support a capsule. Other concepts used “polar tents” and a “foam-shell” to mitigate the effects of the tents. The “polar tents” had significantly reduced contact area between the tents and the capsule compared to the nominal tents. In the “foam-shell” concept, a 200-μm thick, 30 mg/cc SiO 2 foam layer was used to offset the tents away from the capsule surface in an attempt to mitigate their effects. These concepts were investigated in x-ray radiography experiments and compared with perturbations from standard tent support. The measured perturbations in the “fishing pole,” cantilevered fill tube, and “tetra-cage” concepts compared favorably with (were smaller than) nominal tent perturbations and were recommended for further testing for feasibility in layered DT implosions. The “polar tents” were tested in layered DT implosions with a relatively-stable “high-foot” drive showing an improvement in neutron yield in one experiment compared to companion implosions with nominal tents. Furthermore, this article reviews and summarizes recent experiments on these alternate capsule support concepts. In addition, the concept of magnetic levitation is also discussed.
A series of cryogenic, layered deuterium-tritium (DT) implosions have produced, for the first time, fusion energy output twice the peak kinetic energy of the imploding shell. These experiments at the National Ignition Facility utilized high density carbon ablators with a three-shock laser pulse (1.5 MJ in 7.5 ns) to irradiate low gas-filled ( 0.3 mg / cc of helium) bare depleted uranium hohlraums, resulting in a peak hohlraum radiative temperature ~ 290 eV . The imploding shell, composed of the nonablated high density carbon and the DT cryogenic layer, is, thus, driven to velocity on the order of 380 km / s resulting in a peak kinetic energy of ~ 21 kJ , which once stagnated produced a total DT neutron yield of 1.9 × 10 16 (shot N170827) corresponding to an output fusion energy of 54 kJ. Time dependent low mode asymmetries that limited further progress of implosions have now been controlled, leading to an increased compression of the hot spot. Finally, it resulted in hot spot areal density ( ρr ~ 0.3 g / cm 2 ) and stagnation pressure ( ~ 360 Gbar ) never before achieved in a laboratory experiment.
We report a reduced X-ray shadow imprint of hydrodynamic instabilities on the high-density carbon ablator surface of inertial confinement fusion (ICF) capsules using a reduced diameter fuel fill tube on the National Ignition Facility (NIF). The perturbation seed mass from hydrodynamic instabilities was reduced by approximately an order of magnitude by reducing both the diameter and wall thickness of the fill tube by ~2×, consistent with analytical estimates. Overall, this work demonstrates a successful mitigation strategy for engineered features for ICF implosions on the NIF.
High-mode perturbations and low-mode asymmetries were measured in the deceleration phase of indirectly-driven, deuterium gas filled inertial confinement fusion (ICF) capsule implosions at convergence ratios of 10 to 15, using a new “enhanced emission” technique at the National Ignition Facility (NIF) [E. M. Campbell, R. Cauble, and B. A. Remington, AIP Conf. Proc. 429, 3 (1998)]. In these experiments, a high spatial resolution Kirkpatrick-Baez microscope was used to image the x-ray emission from the inner surface of a high-density-carbon (HDC) capsule’s shell. Use of a high atomic number dopant in the shell enabled time-resolved observations of shell perturbations penetrating into the hot spot. This allowed the effects of the perturbations and asymmetries on degrading neutron yield to be directly measured. In particular, mix induced radiation losses of ~400 J from the hot spot resulted in a neutron yield reduction of a factor of ~2. In a subsequent experiment with a significantly increased level of short-mode initial perturbations, shown through the enhanced imaging technique to be highly organized radially, the neutron yield dropped an additional factor of ~2.
Hydrodynamic instability growth of the capsule support membranes (or “tents”) and fill tubes has been studied in spherical, glow discharge polymer plastic capsule implosions at the National Ignition Facility (NIF). In NIF implosions, the capsules are supported by tents because the nominal 10-μm thick fill tubes are not strong enough to support capsules by themselves. After it was recognized that the tents had a significant impact of implosion stability, new support methods were investigated, including thicker, 30-μm diameter fill tubes and cantilevered fill tubes, as described in this article. A new “sub-scale” version of the existing x-ray radiography platform was developed for measuring growing capsule perturbations in the acceleration phase of implosions. It was calibrated using hydrodynamic growth measurements of pre-imposed capsule modulations with Legendre modes of 60, 90, 110, and 140 at convergence ratios up to ~2.4. Subsequent experiments with 3-D perturbations have studied instability growth of 10-μm and 30-μm thick fill tubes to compare them with 30-nm thick tent perturbations at convergence ratios up to ~3. In other experiments, the perturbations from cantilevered fill tubes were measured and compared to the tent perturbations. The cantilevered fill tubes were supported by 12-μm thick SiC rods, offset by 100 μm, 200 μm, and 300 μm from the capsule surfaces. Based on these experiments, 30-μm thick fill tubes and 300-μm offset cantilevered fill tubes were recommended for further tests using layered deuterium-tritium implosions. In conclusion, the effects of x-ray shadowing during the drive and oxygen-induced perturbations during target assembly produced additional seeds for instabilities and were also measured in these experiments.