Engineering topics
Publications and source records attributed to Minott, P. O..
A laser transmitter for high bandwidth geosynchronous satellite communications is described. High optical power is achieved by combining semiconductor laser diodes. An active alignment scheme is proposed for achieving the +/- 20 microrad post launch multiple laser angular co-alignment requirement.
A 650 Mbps laser communications testbed under construction for the development of flight qualifiable hardware suitable for near-term operation on geosynchronous-to-geosynchronous crosslink missions is presented. The program's primary purpose is to develop and optimize laser communications unique subsystems. Requirements for the testbed experiments are to optimize the acquisition processes, to fully simulate the long range (up to 21,000 km) and the fine tracking characteristics of two narrow-beam laser communications terminals, and to fully test communications performance which will include average and burst bit error rates, effects of laser diode coalignment, degradation due to internal and external stray light, and the impact of drifts in the optical components.
A dual aperture, off-axis catadioptic Schmidt objective is described. It is formed by symmetrically aligning two pairs of Schmidt objectives on opposite sides of a common plane (x,z). Each objective has a spherical primary mirror with a spherical focal plane and center of curvature aligned along an optic axis laterally spaced apart from the common plane. A multiprism beamsplitter with buried dichroic layers and a convex entrance and concave exit surfaces optically concentric to the center of curvature may be positioned at the focal plane. The primary mirrors of each objective may be connected rigidly together and may have equal or unequal focal lengths.
An apparatus for eliminating beamsplitter generated optical aberrations in a pupil concentric optical system providing a plurality of spatially separated images on different focal planes or surfaces is presented. The system employs a buried surface beamsplitter having spherically curved entrance and exit faces which are concentric to a system aperture stop with the entrance face being located in the path of a converging light beam directed there from an image forming objective element which is also concentric to the aperture stop.
Off-axis focal planes make room for beam splitters. System includes two off-axis primary spherical reflectors, each concentric with refractive corrector at aperature. Off-axis design assures large aperture required for adequate spatial resolution. Separate images have precise registration, used for multispectral resource mapping or remote sensing.
Two mutually coherent light beams formed from a single monochromatic light source were directed to a reflecting surface of a rotatable object. They were reflected into an imaging optical lens having a focal plane optically at infinity. A series of interference fringes were formed in the focal plane which were translated linearly in response to angular rotation of the object. Photodetectors were located adjacent the focal plane to detect the fringe translation and output a signal in response to the translation. The signal was fed to a signal processor which was adapted to count the number of fringes detected and develop a measure of the angular rotation and direction of the object.
Beam splitter with curved entrance and exit surfaces introduces less chromatic aberration and Seidel aberrations in some optical systems than traditional plate or block beam splitters. Spherical-surface beam splitter is used in Schmidt-type mirror objective to split converging image-forming beam so two images are formed. Small aberrations introduced are corrected by compensator plate located at or near aperture stop.
A special purpose optical collimator system which generates multiple collimated light beams with precisely related angular separation of the beams, is comprised of a stack of relatively flat plate-like refracted prisms in the form of wedges. Each prism has a specified angular deviation, mounted on top of one another in a fixture which holds the wedges so that they are adapted to operate at minimum angular deviation and thus are relatively insensitive to rotational and angular charges. A collimated sources of monochromatic light, generated for example by a helium-neon laser and a collimated beam expander, provides a common incident beam to the wedges whereupon a number equally spaced emergent beams are provided.
Interference fringes from superimposed beams move across a photodetector, creating electrical pulses. Frequency of pulses is direct measure of angular velocity of rotating body. If separation of the sources changes, it affects separation of all fringes equally and does not affect angular velocity measurement.
Optical instrument creates many divergent light beams for surveying and machine element alignment applications. Angles and refractive indices of stack of prisms are selected to divert incoming laser beam by small increments, different for each prism. Angles of emerging beams thus differ by small, precisely-controlled amounts. Instrument is nearly immune to vibration, changes in gravitational force, temperature variations, and mechanical distortion.
The prelaunch testing performed on the Geos-3 laser reflector array before launch was used to determine the lidar cross section of the array and the distance of the center of gravity of the satellite from the center of gravity of reflected laser pulses as a function of incidence angle. Experimental data are compared to computed results.
The LAGEOS was extensively tested optically prior to launch. The measurement techniques used are described and resulting data is presented. Principal emphasis was placed on pulse spreading characteristics, range correction for center of mass tracking, and pulse distortion due to coherent effects. A mode-locked freqeuncy doubled Nd:YAG laser with a pulse width of about 60 ps was used as the ranging transmitter and a crossfield photo-multiplier was used in the receiver. High speed sampling electronics were employed to increase receiver bandwidth. LAGEOS reflected pulses typically had a width of 250 ps with a variability in the range correction of less than 2 mm rms. Pulse distortion due to coherent effects was inferred from average waveforms and appears to introduce less than + or - 50 ps jitter in the location of the pulse peak. Analytic results on this effect based on computer simulations are also presented. Theoretical and experimental data on the lidar cross section were developed in order to predict the strength of lidar echoes from the satellite. Cross section was measured using a large aperture laser collimating system to illuminate the LAGEOS. Reflected radiation far-field patterns were measured using the collimator in an autocollimating mode. Data were collected with an optical data digitzer and displayed as a three-dimensional plot of intensity versus the two far-field coordinates. Measurements were made at several wavelengths, for several types of polarizations, and as a function of satellite orientation.
The satellite coordinate system necessary to describe the location and orientation of each cube corner in the array is discussed. The method of optical testing is described along with the gain function, and computational methods for deriving the gain function and experimental values for it. The velocity aberration is derived as a function of satellite orbit, a complete method for cross section evaluation is described, and finally the radar equation is described.
The characteristics of the earth's atmosphere and its effects upon laser beams was investigated in a series of balloon borne, optical propagation experiments. These experiments were designed to simulate the space to ground laser link. An experiment to determine the amplitude fluctuation, commonly called scintillation, caused by the atmosphere was described.
The radar equation for laser ranging of satellites is described and the effect of the velocity aberration explained. Equations for the cross sections of cube corners and arrays of cube corners are derived. Interference effects on the distribution of the array cross section and upon range error are described. Tolerance requirements for cube corners are briefly outlined.
Theoretical and mathematical considerations involved in the design of retroreflectors for the GEOS-C and Timation III laser ranging satellites are described, laser ranging systems used by the Goddard Space Flight Center are reviewed, and planned systems changes are outlined. Equations are derived for the design of a cube corner array on a gravity gradient stabilized satellite in a circular orbit, and the required cube corner for GEOS-C is computed. Use of fixed threshold triggers and electronic and analytic pulse height compensation in present laser ranging systems is discussed. Proposed changes are outlined, including the incorporation of split gate triggers and trackers into the ranging systems and the use of analog and digital centroid measurement techniques. A theoretical consideration of the effects of velocity aberration on the reflected light beam is appended.
The wave structure function associated with atmospheric turbulence is important in the effective design of telescopes for coherent optical receivers. This paper describes a method of measurement of the wave structure function by employing an already existing optical receiver. The aperture of this receiver's telescope is masked by an opaque screen with two small holes. It is then shown that when the incident beam obeys Gaussian statistics, the receiver's A.M. output can be simply related to the wave structure function of the incident beam.
The bias in scintillation measurements caused by the proximity of a spherical-wave source to the turbulence region of the atmosphere is predicted, and the laser-source altitude required for meaningful experiments simulating space-to-earth laser propagation is estimated. It is concluded that the source should be located at two or more times the maximum altitude of the tropopause to ensure that all measurements are not biased by more than 25%. Thus the vehicle used for experiments of this type should be capable of reaching a minimum altitude of 32 km.