Engineering topics

Mirkarimi, Paul B.

Publications and source records attributed to Mirkarimi, Paul B..

5 records

DOE OSTI2024

Demonstrating resonant ultrasound spectroscopy as a viable technique to characterize thermally conditioned high explosive materials

We present results of resonant ultrasound spectroscopy (RUS) measurements applied to granular high explosive materials at different bulk pressing densities and degree of thermal conditioning. The material chosen in this study is a ubiquitously used explosive material known as pentaerythritol tetranitrate (PETN), which is used commercially in civil and defense applications both as a binderized plastic bonded explosive material and an unbinderized neat material. However, changes in granular PETN bulk elastic properties due to thermal conditioning, which could have implications for better understanding environmental aging-related effects, have not been well studied even though it is believed that elasticity may play an important role in explosive material initiation mechanisms. Furthermore, monitoring elastic property changes in granular explosive pressings has not yet been demonstrated using RUS, which is an appealing non-destructive characterization tool that requires only dry point contact with the explosive material. To this end, we report the first study using RUS to quantify the elastic properties of binderized and neat PETN pressings as well as to quantify changes in elastic properties as a function of both thermal conditioning and bulk pressing density. Elastic stiffness coefficients, sometimes more commonly referred to as elastic constants, calculated from the RUS measurements on the different PETN-based materials show a significant increase for the post-conditioned samples compared to the pre-conditioned samples. This trend of increasing elastic properties with thermal conditioning was consistent for different density pressings, different thermal exposure conditions, and even different neat PETN pressings of differing average crystal sizes and/or specific surface areas.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Ultrathick Boron Carbide Coatings for Nuclear Fusion Targets

Boron carbide is an attractive ablator for next-generation inertial confinement fusion (ICF) targets. Here we describe several aspects of our ongoing systematic studies of the deposition and processing of B 4 C coatings for ICF targets. We show that residual compressive stress in films can be reduced and the deposition rate increased by N-doping. Further, we also demonstrate successful Si substrate etching and surface polishing and discuss remaining challenges and offer potential solutions to the buildup of particulates in the deposition chamber during prolonged coating runs, control of nodular growth defects, and lateral nonuniformity of film properties for deposition conditions with relatively low target-to-substrate distances.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Review of the Effects of Polymer Binder Properties on Microstructure and Irreversible Volume Growth of Plastic Bonded Explosives Formulations

The rational design of effective polymeric binders for the formulation of plastic-bonded explosives (PBX) is challenging due to their inherent compositional complexity. The composites comprise irregularly shaped energetic material (EM) powders coated with low weight fractions of polymer via non-equilibrium processes such as slurry coating. Defects can deleteriously affect PBX stability and performance: nano- to micrometer-scale voids can act as loci for hot spots, lowering deflagration and detonation temperatures in unpredictable ways. Furthermore, some nominally desirable polymer properties are at odds with each other: e. g. good flow characteristics are desirable for coating and adhesion, but mechanical stiffness is needed to prevent deformation and cracking of PBX under mechanical stress. Good binder adhesion is critical, but the best means to predict and measure adhesion in PBX is not obvious. Experimental methods of determining binder adhesion on model surfaces may not capture polymer structural configurations relevant to deposition during coating. Molecular dynamics-based computational models have predicted key observables in PBX formulation, suggesting that they may be powerful tools for binder selection. In this review, primarily recent (~2006 and later) literature on polymeric binders for insensitive HE (IHE) is surveyed. We focus on how binder properties influence observable PBX properties as resistance to irreversible volume growth and void formation in PBX formulations mainly (but not exclusively) featuring 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) as the EM (e. g. PBX 9502, LX-17 and others). Conclusions from these studies yield useful guidelines for choosing HE binder candidates, as well as for the general design of highly-filled polymer composite materials. Finally, studies describing challenges in PBX formulation with the newer and more energetically dense high explosive, LLM-105, will be discussed.

adhesion↗

DOE OSTI2022

Fracture toughness and crack propagation in LX-17 and PBX 9502 insensitive high explosives

High explosive materials, and in particular insensitive high explosive (IHE) materials, are of significant interest. TATB-based LX-17 and PBX 9502 are two IHE’s and mechanical properties are an important metric of performance. In this work we present, for the first time, a study of fracture as a function of temperature and displacement rate and starter crack length on billet pressed IHE materials using a standard three point bend technique. We demonstrated that the technique can yield consistent results over time by measuring samples from the same lots 4 years later and observed that the fracture toughness of LX-17 and PBX 9502 are similar. We also determined the temperature dependence for different starter crack lengths and found that the fracture toughness generally decreases with larger starter crack sizes and temperatures. For the LX-17, where a wide temperature range of -60 C to 50 C was investigated, the impact of temperature on fracture toughness between -20 C and 23 C was less than expected. For the PBX 9502 we observed the difference in fracture toughness values between -20 C and 23 C did depend on the particular lot, and also there was a tendency of the fracture toughness to scale with the tensile strength. We also investigated the effect of a lower displacement rate and observed that while the impact on the fracture toughness was relatively small, the samples surprisingly did not break (fail) after exceeding the peak load. We took advantage of this to perform x-ray computed tomography (CT) of the samples to image crack propagation in the intact samples. We observed that cracks were generally straight and unaffected by the microstructure in the LX-17, in contrast to the PBX 9502 where the direction of the cracks would frequently change and were likely influenced by the underlying microstructure.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Planarization of optical substrates

A method of making a laser mirror in which a mirror substrate has at least a one micron size nodular defect includes depositing a planarization layer over the mirror substrate and the nodular defect, depositing a layer of silicon dioxide over the planarization layer, and etching away a portion of the layer of silicon dioxide. The method also includes thereafter, depositing a layer of hafnium dioxide over the layer of silicon dioxide and repeating the steps of depositing a layer of silicon dioxide, etching away a portion of the layer of silicon dioxide, and depositing a layer of hafnium dioxide until the nodular defect is reduced in size a predetermined amount.

Stolz, Christopher J.↗