Engineering topics
Publications and source records attributed to Miserentino, R..
Composite materials of quasi-isotropic strength obtained. Fiberreinforced polymer matrix material produced by pulling fibers through polymer resin system and then through preforming dies and heated curing die. Experiments with pultrusion conducted in advancedcomposites technology with applications to aeronautical and space structures.
Explore the source record for details and available documents.
Vibration studies carried out in a vacuum chamber are reported for a three-sided membrane with inwardly curved edges. Uniform tension was transmitted by thin steel cables encased in the edges. Variation of ambient air pressure from atmospheric to near vacuum resulted in increased response frequencies and amplitudes. The first few vibration modes measured in a near vacuum are shown to be predictable by a finite element structural analysis over a range of applied tension loads. The complicated vibration mode behavior observed during tests at various air pressures is studied analytically with a nonstructural effective air-mass approximation. The membrane structure is a candidate for reflective surfaces in space antennas.
A description is provided of the results of a series of base driven random dynamic load tests of the Thermal Protection System (TPS). The results were used to insure the integrity of the undensified TPS prior to the first flight in the wing and mid-fuselage region. The number of specimens and the load ranges investigated were limited. Attention is given to the test specimens, the test procedure, a data analysis, and a discussion of the results. All specimens for both the wing and mid-fuselage regions survived an equivalent of 72 ascent missions and exhibited residual static strength greater than their original proof loads. These results indicate that the undensified tiles had sufficient strength to withstand ascent loads during the first flight.
Vibration tests were performed on the tile/strain-isolator-pad system used as thermal protection for the space shuttle orbiter. Experimental data on normal and in-plane vibration response and damping properties are presented. Three test specimens exhibited shear type motion during failures that occurred in the tile near the tile/strain-isolator-pad bond-line. A dynamic instability is described which has large in-plane motion at a frequency one-half that of the nominal driving frequency. Analysis shows that this phenomenon is a parametric response.
A transducer that combines a noncontacting displacement probe with a self-contained target is described. The target is held in position against a vibrating surface by a housing which also supports the noncontacting probe. The target vibrates with the surface and the probe senses the vibrations of the target.
A comparison of the performance of modern modal data analysis methods on test data from the Voyager Jupiter/Saturn payload is presented. Four different test/data-analysis combinations are compared - multiple-point sine excitation tests, single-point random-excitation tests using two different techniques of manipulating Fourier transform data, and a time-domain method for analyzing random data. Results indicate that all four methods can give comparable results. Of the four, the time-domain approach detects more modes in the test data and, at the same time, shows the greatest promise for reducing the time and cost of modal testing.
A flightweight panel based on a metallic thermal-protection-system concept for hypersonic and reentry vehicles was subjected repeatedly to thermal cycling by quartz-lamp radiant heating using a thermal history representative of a reentry heat pulse and to aerodynamic heating at heating rates required to sustain a surface temperature of 1089 K (1960 R). The panel consisted of a corrugated heat shield and support members of 0.05-cm (0.02-in.) thick Rene 41 of riveted construction and 5.08-cm (2-in.) thick silica fibrous insulation packages covered by Rene 41 foil and inconel screening. All tests were conducted in the Langley 8-foot high-temperature structures tunnel with the heat shield corrugations alined in the stream direction. The panel sustained 5.33 hr of intermittent radiant heating and 6.5 min of intermittent aerodynamic heating of up to 1-min duration for differential pressures up to 6.2 kPa (0.9 psi) with no apparent degradation of thermal or structural integrity, as indicated by temperature distributions and results from load deflection tests and vibration surveys of natural frequencies.
Attached-inflatable-decelerator (AID) canopies fabricated from lightweight Nomex cloth and tapes were deployed in a supersonic stream from the base of a 140 deg conical aeroshell. Characteristics of the deceleration system were obtained over a wide range of Mach number, dynamic pressure, and pitch angle. All models deployed rapidly by ram air and experienced only mild deployment shock loads. Steady-state drag coefficients as high as 1.3 were obtained in the supersonic stream and were relatively insensitive to Mach number, dynamic pressure, and pitch angle. All models were free of fluttering motion. Results also showed that the AID is aerodynamically more efficient without a burble fence in a supersonic stream. Though measured meridian-tape loads were higher than those predicted by theory, the ram-air deployment rates and steady-state drag coefficients were in good agreement with theory. These results indicate that the AID is a stable, efficient decelerator in a supersonic stream and its performance is readily predictable.
The vibration and buckling characteristics of a series of 140 deg ring-supported conical shells have been investigated experimentally and analytically. Experimental results were obtained from 14 conical shells, each attached to a solid nose cap at the small end. The large (base) end was either free or attached to a solid ring of rectangular cross section. The size of the solid base rings of rectangular cross section was systematically varied to provide a wide range of edge restraint. Shell buckling was induced by aerodynamic loading at a Mach number of 3; the vibration data were obtained prior to the wind tunnel tests. The experimental vibration data indicated that the size of the base rings had a pronounced effect on the magnitude of the frequencies and on the frequency spectrum. For vibration modes having less than two circumferential waves, the frequencies descreased with increasing ring size; whereas, for modes with several circumferential waves, the frequencies initially increased rapidly with ring size and then became relatively insensitive to further increases in ring size. This latter behavior was similar to the trend exhibited by the variation of buckling pressure with ring size. The experimental results were in excellent qualitative agreement with theoretical results and indicated that current shell-of-revolution analyses are adequate for predicting the vibration and buckling behavior of ring-supported shells, at least for the simple isotropic shells considered in this investigation.
Mach 8 variable-density tunnel used for determination of aerodynamic heating of attached inflatable decelerator configurations
Vibration and flutter tests of pressurized thin walled truncated conical shell
Theoretical and experimental vibration and buckling results for blunt truncated conical shells with ring supported edges
Attached Inflatable Decelerator for planetary atmospheric entry, discussing mission applications and wind tunnel models performance
Deployment and steady state performance of supersonic attached inflatable decelerator canopy models
Drag characteristics of toroid-membrane and wide-angle conical shells used as towed decelerators
Vibration tests of pressurized thin walled cylindrical shells