Search NASA⌕ Search

Engineering topics

Mishra, Rajiv S.

Publications and source records attributed to Mishra, Rajiv S..

24 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Microstructure–Property Correlation in a Laser Powder Bed Fusion Processed High-Strength AF-9628 Steel

Laser powder bed fusion additive manufacturing (LPBF-AM) of a low-alloy, high-performance AF-9628 steel results in exceptionally high strength and good ductility. The reasons for such mechanical properties are investigated through detailed microscopy performed at several length scales. Thus, the characterization of melt pool, porosity, grain morphology, phases, and dislocations is performed in the as-printed material. The as-printed material consists of only 0.004 vol% of uniformly distributed porosity, single-phase martensitic laths with an average lath size of ≈2.5 μm, the absence of carbides indicating interstitial trapping of C atom, and high dislocation density in the martensitic laths. Experimental data through microscopy are then fed in analytical models for calculating strengthening contributions from various strengthening mechanisms. Calculated yield strength agrees well with experimentally determined value, and therefore, activation of various strengthening mechanisms is established in as-printed AF-9628.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dynamic Shear Deformation of a Precipitation Hardened Al 0.7 CoCrFeNi Eutectic High-Entropy Alloy Using Hat-Shaped Specimen Geometry

Lamellar eutectic structure in Al 0.7 CoCrFeNi high-entropy alloy (HEA) is emerging as a promising candidate for structural applications because of its high strength-ductility combination. The alloy consists of a fine-scale lamellar fcc + B2 microstructure with high flow stresses > 1300 MPa under quasi-static tensile deformation and >10% ductility. The response to shear loading was not investigated so far. This is the first report on the shear deformation of a eutectic structured HEA and effect of precipitation on shear deformation. A split-Hopkinson pressure bar (SHPB) was used to compress the hat-shaped specimens to study the local dynamic shear response of the alloy. The change in the width of shear bands with respect to precipitation and deformation rates was studied. The precipitation of L1 2 phase did not delay the formation of adiabatic shear bands (ASB) or affect the ASB width significantly, however, the deformed region around ASB, consisting of high density of twins in fcc phase, was reduced from 80 μm to 20 μm in the stronger precipitation strengthened condition. We observe dynamic recrystallization of grains within ASBs and local mechanical response of individual eutectic lamellae before and after shear deformation and within the shear bands was examined using nano-indentation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effect of temperature on the fatigue cracking mechanisms in A356 Al alloy

This work builds on our previous investigation of the room temperature fatigue cracking mechanisms of an A356 Al alloy. Here, we analyze the elevated temperature fatigue cracking mechanisms in cast and friction stir processed (FSP) A356, and contrast them with the room temperature behavior. Two sets of FSP parameters were used to modify the microstructure of the cast alloy. After heat treatment, both the FSPed microstructures exhibited severe abnormal grain growth (AGG) leading to a very wide grain size distribution (from a few microns to a few millimeters). During room temperature fatigue tests, the FSP conditions exhibited significant improvements in fatigue lives, even up to an order of magnitude. However, with increasing temperature, the difference in the performance of the FSPed and Cast microstructures decreased until, at 200 °C, all three microstructural conditions exhibited similar fatigue response. Detailed electron back scattered diffraction (EBSD) imaging of failed fatigue specimens was used to study crack behavior. At room temperature, cracks initiated at defect sites or along persistent slip bands (PSBs) and propagated transgranularly. The grain boundaries acted as barriers to crack growth. At elevated temperatures, there was a complete role reversal of the grain boundaries. Cracks initiated along grain boundaries and propagated intergranularly in all microstructures. Below, we explore this transition of the cracking mechanism in detail.

Nelaturu, Plalgun↗
DOE OSTI2020

Excellent high cyclic fatigue properties of a novel ultrafine-grained medium entropy alloy

Fatigue is a major cause of failure and requires dedicated investigation to validate the integrity of potential structural materials. As high and medium entropy alloys (HEAs and MEAs) are garnering significant attention from scientific communities, it is important to test the structural integrity of these novel alloys in cyclic loading environment. This study analyzed both monotonic and cyclic loading properties of a novel medium entropy alloy (MEA) CoCr 1.3 Ni in the ultrafine-grained (UFG) and fine grain (FG) conditions. The UFG MEA performs better than the FG MEA during cyclic loading. Microstructural evolution after cyclic loading via electron back-scattered diffraction shows microstructural stability of both FG and UFG microstructures. Transmission electron microscopy suggests formation of stacking faults and fine-scale HCP transformation during cyclic loading.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Notch-tensile behavior of Al0.1CrFeCoNi high entropy alloy

Notch-tensile behavior of an Al0.1CrFeCoNi high entropy alloy (Al0.1-HEA) was studied using V-notch geometry and with local strain mapping using digital image correlation (DIC). A notch-strength ratio of 1.51 indicated notch strengthening. Further analysis of stress-strain response supplemented with microstructural analysis revealed that, while the presence of notch results in strengthening due to work hardening by twinning induced plasticity, the notch also contributes strongly to geometrical softening in the non-uniform ductility regime, and accounts for the onset of failure. The strain localization behavior of Al0.1-HEA due to the presence of V-notch was compared with three conventional alloys: Inconel 625 nickel-based superalloy, 304 stainless steel and Ti–6Al–4V titanium alloy. The study revealed that the nature of notch widening with increasing strain was dependent on material characteristics. The extent of notch widening impacted the local strain field and stress distribution, thereby influencing the propensity for crack initiation and growth. The experimental results were verified by finite element analysis.

Sinha, Subhasis↗