Specifications of FIPD Fission Gas Release Data
Explore the source record for details and available documents.
Mo, Kun↗
Engineering topics
Mo, Kun
Publications and source records attributed to Mo, Kun.
Quality Assurance of Legacy Post-Irradiation Examination Data for Metallic Fuels
The U.S. DOE-NE’s Advanced Reactor Technologies (ART) Fast Reactor Program (FRP) and the NE-4 Advanced Fuels Campaign (AFC) have jointly undertaken the qualification of the legacy post-irradiation examination (PIE) data held in the Fuels Irradiation & Physics Database (FIPD), covering metallic fuel experiments conducted in the Experimental Breeder Reactor II (EBR-II) and the Fast Flux Test Facility (FFTF). In FY26 this effort reached a milestone: six major types of PIE data—contact profilometry, isotopic gamma scan, fission gas chemistry, fission gas release, laser profilometry, and neutron radiography—have been qualified for all available experiments in FIPD, and the U.S. nuclear industry can now draw on them with confidence in licensing activities for metallic fuel-based advanced fast reactors. This report documents the qualification process and the resulting status of the PIE data.
Mo, Kun↗
Under the microscope: Reduced activation ferritic martensitic steel Eurofer-97 following ion-Irradiation and high-temperature high-pressure water exposure
Here, this study is designed to characterise the microstructural behaviour of Eurofer-97 steel under ion irradiation and subsequent exposure to high-temperature high-pressure (HTHP) water. Eurofer-97, a ferritic-martensitic steel, has been developed to withstand the conditions of fusion reactors in the locations in contact with coolant with an elevated level of neutron flux, such as the breeder-wall blanket. The material has been studied after self-ion irradiation (using Fe ions) simulating the microstructural effects of neutron irradiation limited to the subsurface layer. The corrosion properties of the Eurofer-97 steel were studied by exposure to HTHP water up to 331 °C. Advanced microstructural characterisation using scanning, transmission electron and focused ion beam microscopy was performed on the as-received microstructure and after ion irradiation. This was then characterised after exposure for 240 h in high-temperature water. Eurofer-97 had a dense, columnar Cr-rich inner oxide, followed by a Fe-rich outer oxide layer. In the irradiated condition the grain structure and oxide itself was less ordered. No appreciable difference in oxide thickness was identified between the irradiated and unirradiated specimens after this short exposure time.
36 MATERIALS SCIENCE↗
MOOSE-Workbench integration and MOOSE meshing capability enhancements to facilitate inputs and outputs for multiphysics modeling
The Multiphysics Object-Oriented Simulation Environment (MOOSE) is an open-source framework that supports many of the US Department of Energy’s (DOE’s) Nuclear Energy Advanced Modeling and Simulation (NEAMS) technical areas (TA). These TAs develop and use NEAMS physics and coupling modules in multiple ways to enable the research and development of complex physics models. In addition to the MOOSE framework, the NEAMS Workbench user interface provides a common analysis environment with user-interaction accelerators that streamline the tasks of model creation, review, execution, and out put inspection. In FY 2024, objectives were realized in the MOOSE framework application development support and user-oriented improvements. Application development improvements support both developers and users with an expanded Reactor Module and Mesh System, stateful material property support for mortar contact, and customizable convergence criteria. Additionally, new user-oriented features were implemented in the MOOSE framework language server, including autocompletion snippets, definition from source and find reference navigations, and syntax overrides. Lastly, improvements were made to the input interpreter necessary to support the MOOSE language server and the NEAMS Workbench so that they can interact with syntactically incomplete user inputs. These improvements and more were intended to address stakeholder feedback and improve developer and user ability to conduct advanced nuclear energy modeling and simulation in support of DOE and industry needs.
73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
MOOSE–Workbench Integration and MOOSE Meshing Capability Enhancements to Facilitate Inputs and Outputs for Multiphysics Modeling
The Multiphysics Object-Oriented Simulation Environment (MOOSE) is an open-source framework that supports many of the US Department of Energy’s (DOE’s) Nuclear Energy Advanced Modeling and Simulation (NEAMS) technical areas (TA). These TAs develop and use NEAMS physics and coupling modules in multiple ways to enable the research and development of complex physics models. In addition to the MOOSE framework, the NEAMS Workbench user interface provides a common analysis environment with user-interaction accelerators that streamline the tasks of model creation, review, execution, and output inspection. In FY 2024, objectives were realized in the MOOSE framework application development support and user-oriented improvements. Application development improvements support both developers and users with an expanded Reactor Module and Mesh System, stateful material property support for mortar contact, and customizable convergence criteria. Additionally, new user-oriented features were implemented in the MOOSE framework language server, including autocompletion snippets, definition from source and find reference navigations, and syntax overrides. Lastly, improvements were made to the input interpreter necessary to support the MOOSE language server and the NEAMS Workbench so that they can interact with syntactically incomplete user inputs. These improvements and more were intended to address stakeholder feedback and improve developer and user ability to conduct advanced nuclear energy modeling and simulation in support of DOE and industry needs.
97 - MATHEMATICS AND COMPUTING↗
Effect of TiN coating on suppressing Ce-Fe interaction under irradiation
Advanced cladding is critical for fast reactors with the adequate thermal conductivity, mechanical stability and radiation tolerance of the cladding base material, corrosion resistance and high temperature coolant compatibility of the cladding surface, and chemical stability of the cladding inner wall against fuel cladding chemical interaction (FCCI). The preliminary results of recent ion irradiation studies of two diffusion-couple samples of cerium (Ce)/oxide-dispersion strengthened steel (ODS) and Ce/TiN/ODS, irradiated with 80 MeV xenon (Xe) ions to 100 displacements per atom (dpa) at 500°C, are summarized. Significant Ce-Fe interaction occurred in the Ce/ODS sample, and no noticeable Ce-Fe interaction was found in the Ce/TiN/ODS sample. It shows the effectiveness of 1-µm TiN diffusion barrier coated by the pulsed laser deposition on suppressing Ce-Fe interaction, a major contributor to FCCI in cladding. Here, density function theory (DFT) calculations of the impurity diffusivities of Ce and Fe within the Ti sublattice of TiN were performed to assist a mechanistic understanding of the experimental results.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
High-Fidelity Multiphysics Modeling of a Heat Pipe Microreactor Using BlueCrab
Researchers who are actively developing nuclear microreactors are planning to employ innovative designs and features using traditional commercial modeling tools that may be inadequate for their design and licensing activities. The codes developed under the U.S. Department of Energy Office of Nuclear Energy Advanced Modeling and Simulation (NEAMS) program provide flexibility in terms of geometry modeling and multiphysics coupling and are particularly well suited for modeling novel microreactor concepts. To test the maturity of these codes, this paper introduces a conceptual heat pipe microreactor (HP-MR) designed to gather various technologies of interest to microreactor developers such as control drums, heat pipes, and hydride moderators. Here, the objective of this effort is to demonstrate NEAMS tools capability to perform high-fidelity multiphysics simulations, using coupled neutronics (via the Griffin code), heat conduction (via the BISON code), heat pipe modeling (via the Sockeye code), and hydrogen redistribution in hydride metal moderator (via the SWIFT code). Codes are coupled in-memory through the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework, which permits flexible multiphysics data transfer schemes. The analysis confirmed two key aspects of the HP-MR concept: (1) its ability to follow the power load requested from the heat pipe and (2) its ability to avoid heat pipe cascading failure unless designed with high power close to operating failure limits of its heat pipes. The developed computational model was distributed publicly on the Virtual Test Bed for training purposes to accelerate adoption by industry and to provide a high-fidelity multiphysics solution for benchmarking against other tools. Additional multiphysics analyses including other transients and coupled physics were identified as necessary future work, together with a focus on validating multiphysics behavior against experiments.
Microreactor↗
Advances in Metallic Fuel Database Development and Data Qualification
The Fuels Irradiation and Physics Database (FIPD [1]) is a comprehensive repository of data and documents related to Uranium-Zirconium based metallic fuel test pins. This database stores operational conditions of these pins, calculated using a suite of Argonne National Laboratory analysis codes developed during the Integral Fast Reactor (IFR) program. Key calculated data include axial distributions of power, temperature, fluence, burnup, and isotopic densities. Additionally, the FIPD holds post-irradiation examination (PIE) data such as fission gas release, gas chemistry measurements, and axial distributions derived from profilometry, gamma scanning, and neutron radiography. Complementing these data is an extensive archive of documents related to various pins and experiments. These include raw PIE records, design details, safety analyses, and operational reports. More detail about FIPD can be found in ref. [2]. The database development is an ongoing effort covering metallic fuel experiments from the Experimental Breeder Reactor II (EBR-II) and the Fast Flux Test Facility (FFTF). The recent improvements to the database and the data QA status are summarized in this paper.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Summary Report on Ion Irradiation Study of Ceramic Coating on Suppressing FCCI
Advanced cladding is critical for advanced nuclear reactors with an enhanced performance in radiation tolerance and neutron transparency. Using advanced cladding will ensure the adequate thermal conductivity and mechanical stability of the cladding base material, corrosion resistance, high-temperature coolant compatibility of the cladding surface, and chemical stability in the cladding inner wall against fuel cladding chemical interaction (FCCI). An innovative cladding with a three-layer structure (i.e., a modified surface, a clad base material, and a modified inner wall) promises to meet all these requirements. Initial research and development (R&D) regarding this innovative cladding seek to demonstrate the effectiveness of a thin ceramic coating in suppressing FCCI under ion irradiation to high dose. This United States (U.S.) Department of Energy (DOE)–Office of Nuclear Energy (NE) project report summarizes the results of recent ion irradiation studies of diffusion-couple samples with details of an ion irradiation experiment, the characterization of the interface microstructure of cerium (Ce)/titanium nitride (TiN)/oxide-dispersion strengthened (ODS), Ce/TiN/iron (Fe), Ce/ODS, and Ce/Fe samples irradiated with 80 million electron-volts (MeV) of xenon (Xe) ions to 100 displacements per atom (dpa) at 500?C using the Argonne Tandem Linac Accelerator System (ATLAS) facility at Argonne National Laboratory (ANL). The results of the ODS-substrate sample are encouraging and demonstrate the effectiveness of a thin ceramic coating on FCCI mitigation under irradiation. The results from an Fe-substrate sample revealed a complex microstructure, and the root cause is discussed.
36 MATERIALS SCIENCE↗
Specification of EBR-II Fabricated Fuel Diameter Data
All IFR EBR-II fuel pins were fabricated at one of the related fuel fabrication facilities at Argonne National Laboratory-West, at the EBR-II site [1]. U-Pu-Zr experimental pins were fabricated at the Experimental Fuels Laboratory (EFL), which was established in April of 1984 after the positive acceptance of the IFR concept, while the U-Zr experimental pins were fabricated at the Fuel Manufacturing Facility (FMF), along with the driver fuel pins [2]. The injection-casting fabrication process is described in detail in ref [1]. All the fuel pins that were loaded into EBR-II were examined after fabrication to ensure that they met the design dimensional requirements and tolerances prior to assembly. Fuel slug diameter was measured with either a laser profilometer (at FMF) or a hand micrometer (at EFL), at a minimum of 1-inch intervals over the length of the fuel slug, as shown in Figure 1 [2]. In all cases the average fuel diameter is reported, in some cases with additional summary statistics (e.g., minimum, maximum), and in rare cases the complete record of axially-varying fuel diameters is available. It should be noted that in cases where axial varying data is available, in general the orientation of the slug was not recorded or carried over to loading of the pin, so a diameter measurement at the bottom of the fabricated slug does not necessarily correspond to the bottom of the loaded slug, as it may have been loaded in either orientation.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Specification of FIPD Fission Gas Chemistry Data
The current FIPD library contains two main sets of fission gas chemistry data. The first set is data collected during the Integral Fast Reactor (IFR) program from 1984 to 1994, using a gas mass spectrometry system located in the Analytical Laboratory (AL) at Argonne National Laboratory-West (Argonne-West). Throughout this period, numerous fission gas release and chemistry datasets were gathered from a variety of metallic fuel pins. The fission gas was sampled by the Gas Assay, Sample and Recharge (GASR) System in the Hot Fuel Examination Facility (HFEF) and transferred to the AL to perform gas composition and isotopic abundance analysis. The second set is data collected after the IFR program. The fission gas samples were also collected by the GASR system at the HFEF, but analyzed using a similar gas mass spectrometer located in Pacific Northwest National Laboratory (PNNL). Many fuel pins irradiated in Experimental Breeder Reactor II (EBR-II) and the Fast Flux Test Facility (FFTF) were measured, including the fuel pins for the MFF series of experiments, designed to qualify metal fuel for use as driver fuel in the FFTF and X496 experiment. For either set of data, fission gas was sampled with the gas sampling line in GASR using sample bottles after the capsule/element volume has been determined and the system is still full of radioactive gas. The sample bottles were then transferred to the sample packaging cylinder or an approved storage location pending transfer to the AL or prepared for shipment to another laboratory (such as PNNL) for analysis of the collected gas as directed on the GASR data form, other approved form. The receiving laboratories (AL or PNNL) required their Analytical Service Request form to be completed prior to sample transfer. Typical sample transfer processes were initiated at HFEF by the principal or process engineer. The laboratories performing the analyses (AL or PNNL) use the sample bottle numbers as well as a sample number produced by the respective laboratory. HFEF and the responsible experimenter tracked the sample using the analysis number, the gas bottle number, and the fuel pin number.
38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
In situ synchrotron investigation of tensile deformation and failure mechanisms in cold spray Cr-coated Zr-alloy system
Not Available
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Improved correlations of the fuel/cladding liquid penetration rate with the out-of-pile transient database
Here, utilizing data from the Out-of-Pile Transient Database (OPTD), we developed advanced correlations for the cladding liquid penetration rate in metallic fuels used in sodium-cooled fast reactors (SFRs). Based on the available OPTD data, our research highlights the key role of Pu concentration in influencing the liquid penetration behavior, showing different threshold fuel-cladding interaction temperatures, with burnup playing a substantial role, particularly in fuels with a 19% Pu concentration. The penetration rate exhibits a parabolic, diffusion-limited behavior, thereby facilitating predictions of maximum liquid penetration depth over time. These correlations are significantly more accurate, under a variety of conditions, compared to existing single-parameter models, and enhance our understanding of SFR metallic fuel behavior, promoting safer and more efficient reactor operations.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
BISON-FIPD integration enhanced low-burnup SFR metallic fuel swelling model evaluation framework
Experiments indicated that metallic fuel in sodium-cooled fast reactors (SFRs) rapidly swells radially and axially at low burnup. Despite that, prior studies have been focused on describing high burnup axial fuel elongation. With recent conventional and non-conventional metallic fuel concepts being considered for license applications, understanding multidimensional fuel swelling at a wide range of burnup levels is important to fuel analysis and qualification activities. Here, we report the development and demonstration efforts of a low-burnup SFR metallic fuel swelling model evaluation framework using the BISON advanced fuel performance code. The framework leverages the Integral Fast Reactor (IFR) program X423 experiment data through the ongoing integration project to enable standardized and automated use of legacy metallic fuel irradiation data maintained in the SFR fuel irradiation and physics database (FIPD) for BISON metallic fuel model verification and validation. In conclusion, the performance of the framework was demonstrated using the two representative metallic fuel swelling model sets implemented in BISON, with a series of insights about future advanced swelling model development.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Specifications of FIPD Fission Gas Release Data
All fission gas release data stored in the Fuels Irradiation & Physics Database (FIPD) was originally measured using the Gas Assay, Sample and Recharge (GASR) System in the Hot Fuel Examination Facility (HFEF). It is therefore called GASR data in FIPD. During the measurement of a sample, such as an irradiated EBR-II fuel element/capsule, a pinhole-sized region near the top of the element plenum was melted by a laser. Plenum gas then expanded into a calibrated volume (note: in this document, “sample” and “capsule/element” are used interchangeably consistent with GASR documents in FIPD). The pressure rise in the volume was recorded. Helium backfilling and expansion was then performed to determine the sample (e.g., fuel element plenum) volume using Boyle’s Law and assuming ideal gas behavior at constant temperature. With the plenum volume and the recorded pressure rise, the sample (e.g., fuel element plenum) pressure was derived with assumption of ideal gas law behavior. The plenum volume and pressure as well as the cladding temperature during the measurement were collected (GASR data in FIPD). Other records associated with the fission gas release data include: raw GASR data records including volumes and post-puncture pressures of seal head/sealing head and manifold, calibration data, backfilling gas pressure data, and the data analysis records. A sample(s) of the fission gas released from the plenum was collected by the GASR system into sample bottles. The chemical and isotopic composition of the gas sample was analyzed separately from GASR data, and will be discussed in a separate specification. The plenum volume, pressure, and cladding temperature during the measurement are typically utilized to determine the number of moles of gas in the plenum. This quantity is often compared to the number of moles of gas generated by fission events. However, calculating these values and their associated uncertainty is beyond the scope of this document, as it necessitates additional assumptions. The most important document to understand the FIPD fission gas data is the GASR operational manual (title: Gas Assay, Sample and Recharge System (GASR) operation and maintenance manual, HFEF/N OMM 4381, DOC. NO. W0018-0032-ES-00). This manual provides: (1) description of the GASR and the functions of each component (laser drilling, welding, seal head/sealing head, manifold, vacuum system, sample system, purge and gas tag system, etc.); (2) step-by-step guidance on calibrations, operations, and measurements; and (3) maintenance procedures and other details relating to the structure and operation of the GASR. Note that the original GASR operated until 2020. A new GASR with the same design and measurement methodology was installed in 2021. The specifications of the GASR presented on the HFEF website at this time are consistent with the ones given in the operational manual. The methods to calculate the plenum volume and pressures were not included in the operational manual, but were recorded in the legacy data analysis files. Details of the methods are given in Chapter 3.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Meshing, Language Server Protocol, and other User-Oriented MOOSE Framework Improvements to Enhance Reactor Analysis Capabilities and Workflows
The open-source Multiphysics Object-Oriented Simulation Environment (MOOSE) framework underpins most of the Nuclear Energy Advanced Modeling and Simulation (NEAMS) physics applications and coupling methods. Users interact with MOOSE in multiple ways to enable the construction of complex multiphysics models, including but not limited to compilation, input creation and syntax validation, meshing, solving the physics problem via MOOSE-based solvers and coupling, and output inspection. In FY23, numerous enhancements have been made to MOOSE to enhance the user experience. Reactor-oriented meshing capabilities in MOOSE have been expanded, an online tutorial was created and hosted on the MOOSE site, and a hands-on workshop was held for more than 100 users. The Language Server Protocol (LSP) capability has been implemented in MOOSE to better communicate correct syntax to the NEAMS Workbench user interface which is commonly used to validate input and submit jobs by users. Finally, several other user-facing improvements were made including the implementation of improved screen output and logging control, enhancements to the initial condition system, and enhancements of the MultiApp system commonly used for coupling. Collectively, these enhancements were driven by user needs and directly improve user ability to construct complex multiphysics models for nuclear reactors.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Thermal conductivity degradation due to radiation-induced amorphization in U 3 Si 2 : A pilot study
Here, in this study, we investigate the thermal conductivity of U 3 Si 2 amorphized by ion irradiation using 84 MeV 136 Xe ions at 190 °C. The suspended-bridge method was utilized to measure the thermal conductivity, allowing for a detailed analysis of the specimen while minimizing interference from other crystalline phases. Our results indicate that the thermal conductivity of amorphous U 3 Si 2 is significantly lower than that of unirradiated crystalline U 3 Si 2 . These findings are consistent with recent studies on in-pile-irradiated U 3 Si 2 samples that consider the effects of U 3 Si 2 amorphization, fission gas bubbles, and other impurities.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Sensitivity Analysis, Reduced-order Modeling, and Optimization of a Gas-Cooled Pebble Bed Reactor using Equilibrium-Core and DLOFC Performance
This work presents and applies a workflow for performing design optimization on gas-cooled pebble-bed reactors. Based on previous research, a representative equilibrium core of a pebble-bed reactor and a depressurized loss-of-forced-cooling model are created. These applications are built using the Multiphysics Object-Oriented Simulation Environment (MOOSE), specifically utilizing Griffin, Pronghorn, and Bison. After defining design-related parameters and quantities of interest regarding reactor safety and efficiency, this multiphysics model is sampled using the MOOSE stochastic tools module. The result is a comprehensive dataset of configurations, enabling sensitivity analysis and the generation of reduced-order models. Subsequently, the dataset and reduced-order models are employed in an optimization study aimed at maximizing fuel utilization while adhering to safety and operational constraints. The optimization process leads to an improvement of fuel utilization by approximately 10\%, compared to engineering-judgment-based nominal conditions.
97 - MATHEMATICS AND COMPUTING↗