Engineering topics
Mo, Yifei
Publications and source records attributed to Mo, Yifei.
Superionic conducting vacancy-rich β-Li 3 N electrolyte for stable cycling of all-solid-state lithium metal batteries
The advancement of all-solid-state lithium metal batteries requires breakthroughs in solid-state electrolytes (SSEs) for the suppression of lithium dendrite growth at high current densities and high capacities (>3 mAh cm -2 ) and innovation of SSEs in terms of crystal structure, ionic conductivity and rigidness. Here we report a superionic conducting, highly lithium-compatible and air-stable vacancy-rich β-Li 3 N SSE. This vacancy-rich β-Li 3 N SSE shows a high ionic conductivity of 2.14 × 10 -3 S cm -1 at 25 °C and surpasses almost all the reported nitride-based SSEs. A Li- and N-vacancy-mediated fast lithium-ion migration mechanism is unravelled regarding vacancy-triggered reduced activation energy and increased mobile lithium-ion population. All-solid-state lithium symmetric cells using vacancy-rich β-Li 3 N achieve breakthroughs in high critical current densities up to 45 mA cm -2 and high capacities up to 7.5 mAh cm -2 , and ultra-stable lithium stripping and plating processes over 2,000 cycles. The high lithium compatibility mechanism of vacancy-rich β-Li 3 N is unveiled as intrinsic stability to lithium metal. In addition, β-Li 3 N possesses excellent air stability through the formation of protection surfaces. All-solid-state lithium metal batteries using the vacancy-rich β-Li 3 N as SSE interlayers and lithium cobalt oxide (LCO) and Ni-rich LiNi 0.83 Co 0.11 Mn 0.06 O 2 (NCM83) cathodes exhibit excellent battery performance. Extremely stable cycling performance is demonstrated with high capacity retentions of 82.05% with 95.2 mAh g -1 over 5,000 cycles at 1.0 C for LCO and 92.5% with 153.6 mAh g -1 over 3,500 cycles at 1.0 C for NCM83. Utilizing the vacancy-rich β-Li 3 N SSE and NCM83 cathodes, the all-solid-state lithium metal batteries successfully accomplished mild rapid charge and discharge rates up to 5.0 C, retaining 60.47% of the capacity. Notably, these batteries exhibited a high areal capacity, registering approximately 5.0 mAh cm -2 for the compact pellet-type cells and around 2.2 mAh cm -2 for the all-solid-state lithium metal pouch cells.
Resistance of Boron Nitride Nanotubes to Radiation-Induced Oxidation
We present unprecedented results on the damage thresholds and pathways for boron nitride nanotubes (BNNT) under the influence of energetic electrons in an oxidative gas environment, using an environmental aberration-corrected electron microscope over a range of oxygen pressures. We observe a damage cascade process that resists damage until a higher electron dose, compared with carbon nanotubes, initiating at defect-free BNNT sidewalls and proceeding through the conversion from crystalline nanotubes to amorphous boron nitride (BN), resisting oxidation throughout. We compare with prior results on the oxidation of carbon nanotubes and present a model that attributes the onset of damage in both cases to a physisorbed oxygen layer that reduces the threshold for damage onset. Surprisingly, increased temperatures offer protection against damage, as do electron dose rates that significantly exceed the oxygen dose rates, and our model attributes both effects to a physisorbed oxygen population.
Dataset for "Resistance of Boron Nitride Nanotubes to Radiation-Induced Oxidation" as published in The Journal of Physical Chemistry C
We present unprecedented results on the damage thresholds and pathways for boron nitride nanotubes (BNNT) under the influence of energetic electrons in an oxidative gas environment, using an environmental aberration-corrected electron microscope over a range of oxygen pressures. We observe a damage cascade process that resists damage until a higher electron dose, compared with carbon nanotubes, initiating at defect-free BNNT sidewalls and proceeding through the conversion from crystalline nanotubes to amorphous boron nitride (BN), resisting oxidation throughout. We compare with prior results on the oxidation of carbon nanotubes and present a model that attributes the onset of damage in both cases to a physisorbed oxygen layer that reduces the threshold for damage onset. Surprisingly, increased temperatures offer protection against damage, as do electron dose rates that significantly exceed the oxygen dose rates, and our model attributes both effects to a physisorbed oxygen population.
Tuning collective anion motion enables superionic conductivity in solid-state halide electrolytes
Halides of the family Li 3 MX 6 (M = Y, In, Sc and so on, X = halogen) are emerging solid electrolyte materials for all-solid-state Li-ion batteries. They show greater chemical stability and wider electrochemical stability windows than existing sulfide solid electrolytes, but have lower room-temperature ionic conductivities. Here, in this work, we report the discovery that the superionic transition in Li 3 YCl 6 is triggered by the collective motion of anions, as evidenced by synchrotron X-ray and neutron scattering characterizations and ab initio molecular dynamics simulations. Based on this finding, we used a rational design strategy to lower the transition temperature and thus improve the room-temperature ionic conductivity of this family of compounds. We accordingly synthesized Li 3 YCl x Br 6-x and Li 3 GdCl 3 Br 3 and achieved very high room-temperature conductivities of 6.1 and 11 mS cm -1 for Li 3 YCl 4.5 Br 1.5 and Li 3 GdCl 3 Br 3 , respectively. These findings open new routes to the design of room-temperature superionic conductors for high-performance solid batteries.
Revealing unprecedented cathode interface behavior in all-solid-state batteries with oxychloride solid electrolytes
The superionic conductor, lithium tantalum oxychloride (LTOC), exhibits unprecedented stability with Co-lean and Ni-rich cathodes, while lowering the working temperature proves effective in regulating the Co-rich cathode interface with LTOC.
Lithium-compatible and air-stable vacancy-rich Li 9 N 2 Cl 3 for high–areal capacity, long-cycling all–solid-state lithium metal batteries
Attaining substantial areal capacity (>3 mAh/cm 2 ) and extended cycle longevity in all–solid-state lithium metal batteries necessitates the implementation of solid-state electrolytes (SSEs) capable of withstanding elevated critical current densities and capacities. In this study, we report a high-performing vacancy-rich Li 9 N 2 Cl 3 SSE demonstrating excellent lithium compatibility and atmospheric stability and enabling high–areal capacity, long-lasting all–solid-state lithium metal batteries. The Li 9 N 2 Cl 3 facilitates efficient lithium-ion transport due to its disordered lattice structure and presence of vacancies. Notably, it resists dendrite formation at 10 mA/cm 2 and 10 mAh/cm 2 due to its intrinsic lithium metal stability. Furthermore, it exhibits robust dry-air stability. Incorporating this SSE in Ni-rich LiNi 0.83 Co 0.11 Mn 0.06 O 2 cathode-based all–solid-state batteries, we achieve substantial cycling stability (90.35% capacity retention over 1500 cycles at 0.5 C) and high areal capacity (4.8 mAh/cm 2 in pouch cells). These findings pave the way for lithium metal batteries to meet electric vehicle performance demands.
Low Impedance Cathode/Electrolyte Interfaces for High Energy Density Solid-State Batteries
All-solid-state batteries (ASSBs) using a ceramic fast Li-ion conductor as a solid-state electrolyte (SSE) have been proposed as a promising strategy to significantly increase the energy density of lithium batteries. Due to their high ion conductivity and excellent stability, Li-stuffed garnets exhibit the most promising physical and chemical properties for SSEs. However, the typical microstructure, thick (>100 μm) bulk electrolyte and simple planar electrode/electrolyte interfaces, combined with poor electrode wetting of the garnet result in excessively high area specific resistances (ASRs) that severely limit achievable current density and cell energy density. In this project, the team is building on their demonstrated expertise with garnet electrolytes and ASSBs to accomplish the following: (1) engineer interfaces to overcome high NMC/LLZ interfacial impedance and interfacial degradation; (2) develop processing and fabrication techniques to achieve high loading NMC/LLZ composite cathodes with low resistance and high cyclability; and (3) integrate the NMC/LLZ cathodes into all-solid-state Li-metal/LLZ cells to achieve high-energy-density batteries.
Understanding the Polymorphism of Cobalt Nanoparticles Formed in Electrodeposition–An In Situ XRD Study
An advanced synchrotron-based in situ X-ray diffraction (XRD) technique is successfully developed and employed to track and monitor the formation and phase selection of cobalt (Co) in electrodeposition in real time and verify DFT computational results. The impacts of a number of controlling factors including the pH of the electrolyte and deposition overpotential are systematically studied. The results show that the yielded phase of the electrodeposited Co is controlled by both thermodynamics and kinetics. The low pH low overpotential condition favors the formation of the thermodynamically stable fcc phase. While the high pH high overpotential condition promotes the formation of the metastable hcp phase. The experimental results agree well with the nanometric phase diagram computed with DFT. Layer-by-layer alternative stacking of fcc-hcp polymorphic phases can be facilely fabricated by just varying the overpotential. This work not only offers an effective means to control the phase of electroplating of Co but also presents a new approach to reveal the fundamental insights of the formation of metals under electrochemical reduction driving force.
Multi-principal elemental intermetallic nanoparticles synthesized via a disorder-to-order transition
Nanoscale multi-principal element intermetallics (MPEIs) may provide a broad and tunable compositional space of active, high–surface area materials with potential applications such as catalysis and magnetics. However, MPEI nanoparticles are challenging to fabricate because of the tendency of the particles to grow/agglomerate or phase-separated during annealing. Here, we demonstrate a disorder-to-order phase transition approach that enables the synthesis of ultrasmall (4 to 5 nm) and stable MPEI nanoparticles (up to eight elements). We apply just 5 min of Joule heating to promote the phase transition of the nanoparticles into L1 0 intermetallic structure, which is then preserved by rapidly cooling. This disorder-to-order transition results in phase-stable nanoscale MPEIs with compositions (e.g., PtPdAuFeCoNiCuSn), which have not been previously attained by traditional synthetic methods. This synthesis strategy offers a new paradigm for developing previously unexplored MPEI nanoparticles by accessing a nanoscale-size regime and novel compositions with potentially broad applications.
Li + Diffusion in Amorphous and Crystalline Al 2 O 3 for Battery Electrode Coatings
Al 2 O 3 is often applied protectively to lithium-ion battery anode and cathode materials to inhibit surface degradation, suppress dendrite formation, and relieve mechanical stresses. Given the very high intrinsic band gap and diffusion barrier of the material, the mechanism that allows Li diffusion through these coatings is not well understood, and widely varying laboratory results indicate that there may be dependencies on morphology and stoichiometry. Using nudged elastic band calculations and ab initio molecular dynamics, we perform a systematic investigation across Al 2 O 3 structures, both crystalline and amorphous, and at various concentrations of Li + to uncover the optimal parameters for maximally diffusive coatings. We find a correlation between the low proximity of Li + to Al 3+ and the low Li + migration barrier. Although barriers are the lowest in the highly diffusive one-dimensional channels of crystalline θ-Al 2 O 3 , the system is structurally delicate and subject to detrimental distortion as the Li + content is increased. The α-Al 2 O 3 lattice is, conversely, highly stable against distortion at all Li + concentrations but disadvantageous for Li + migration. In amorphous systems, unscreened Li + –Li + Coulomb repulsion and pre-emptive occupation of “trapping sites” combine to lower the energy barriers as a function of increasing concentration. One of our most important findings is that Al-deficient materials can sharply increase Li + movement, and we predict that an amorphous material with a combination of high Li + concentration and Al deficiency would enable highly Li + -conductive protective coatings for electrodes.
Interfacial Defect of Lithium Metal in Solid‐State Batteries
Abstract All‐solid‐state battery with Li metal anode is a promising rechargeable battery technology with high energy density and improved safety. Currently, the application of Li metal anode is plagued by the failure at the interfaces between lithium metal and solid electrolyte (SE). However, little is known about the defects at Li–SE interfaces and their effects on Li cycling, impeding further improvement of Li metal anodes. Herein, by performing large‐scale atomistic modeling of Li metal interfaces with common SEs, we discover that lithium metal forms an interfacial defect layer of nanometer‐thin disordered lithium at the Li–SE interfaces. This interfacial defect Li layer is highly detrimental, leading to interfacial failure such as pore formation and contact loss during Li stripping. By systematically studying and comparing incoherent, coherent, and semi‐coherent Li–SE interfaces, we find that the interface with good lattice coherence has reduced Li defects at the interface and has suppressed interfacial failure during Li cycling. Our finding discovered the critical roles of atomistic lithium defects at interfaces for the interfacial failure of Li metal anode, and motivates future atomistic‐level interfacial engineering for Li metal anode in solid‐state batteries.
Advanced High-Voltage All-Solid-State Li-Ion Batteries Enabled by a Dual-Halogen Solid Electrolyte
Explore the source record for details and available documents.
Interfacial Defect of Lithium Metal in Solid-State Batteries
All-solid-state battery with Li metal anode is a promising rechargeable battery technology with high energy density and improved safety. Currently, the application of Li metal anode is plagued by the failure at the interfaces between lithium metal and solid electrolyte (SE). However, little is known about the defects at Li–SE interfaces and their effects on Li cycling, impeding further improvement of Li metal anodes. Herein, by performing large-scale atomistic modeling of Li metal interfaces with common SEs, we discover that lithium metal forms an interfacial defect layer of nanometer-thin disordered lithium at the Li–SE interfaces. Further, this interfacial defect Li layer is highly detrimental, leading to interfacial failure such as pore formation and contact loss during Li stripping. By systematically studying and comparing incoherent, coherent, and semi-coherent Li–SE interfaces, we find that the interface with good lattice coherence has reduced Li defects at the interface and has suppressed interfacial failure during Li cycling. Our finding discovered the critical roles of atomistic lithium defects at interfaces for the interfacial failure of Li metal anode, and motivates future atomistic-level interfacial engineering for Li metal anode in solid-state batteries.
Computation-guided discovery of coating materials to stabilize the interface between lithium garnet solid electrolyte and high-energy cathodes for all-solid-state lithium batteries
All-solid-state batteries with a lithium metal anode, enabled by lithium garnet solid electrolytes such as Li 7 La 3 Zr 2 O 12 (LLZO), are a promising next-generation energy-storage technology. The further development of all-solid-state battery requires the integration of high-energy cathodes such as LiNi 1-x-y Mn x Co y O 2 (NMC) with the garnet solid electrolyte with stable and low-resistance interfaces, which requires a coating layer to stabilize the interface during high-temperature sintering and electrochemical cycling. In order to guide the future development of interfacial coatings, we perform high-throughput thermodynamic analyses based on first-principles computation to investigate the stability of LLZO garnet and high-energy NMC cathodes with a wide range of materials chemistries. Here our study reveals the factors governing the materials stability with LLZO garnet and NMC cathodes, and identifies the mechanisms of good coating layers stable with LLZO and NMC. In addition to classifying known coating layers, our study provides detailed guiding charts and multiple new materials systems as promising coatings for stabilizing LLZO—NMC interfaces to enable high-energy-density garnet-based all-solid-state batteries. Our demonstrated computation scheme and high-throughput analyses are generally applicable to investigate and screen coating materials for stabilizing interfaces in energy-related applications.
AlCl 3 -Dosed Si(100)-2 × 1: Adsorbates, Chlorinated Al Chains, and Incorporated Al
The adsorption of AlCl 3 on Si(100) and the effect of annealing the AlCl 3 -dosed substrate were studied to reveal key surface processes for the development of atomic-precision, acceptor-doping techniques. This investigation was performed via scanning tunneling microscopy (STM), X-ray photoelectron spectroscopy (XPS), and density functional theory (DFT) calculations. At room temperature, AlCl 3 readily adsorbed to the Si substrate dimers and dissociated to form a variety of species. Annealing the AlCl 3 -dosed substrate at temperatures below 450 °C produced unique chlorinated aluminum chains (CACs) elongated along the Si(100) dimer row direction. An atomic model for the chains is proposed with supporting DFT calculations. Al was incorporated into the Si substrate upon annealing at 450 °C and above, and Cl desorption was observed for temperatures beyond 450 °C. Al-incorporated samples were encapsulated in Si and characterized by secondary ion mass spectrometry (SIMS) depth profiling to quantify the Al atom concentration, which was found to be in excess of 10 20 cm –3 across a ~2.7 nm-thick δ-doped region. Here, the Al concentration achieved here and the processing parameters utilized promote AlCl 3 as a viable gaseous precursor for novel acceptor-doped Si materials and devices for quantum computing.
Interfacial layers for solid-state batteries and methods of making same
One or more interfacial layers in contact with a solid-state electrolyte and hybrid electrolyte materials. Interfacial layers comprise inorganic (e.g., metal oxides and soft inorganic materials) or organic materials (e.g., polymer materials, gel materials and ion-conducting liquids). The interfacial layers can improve the electrical properties (e.g., reduce the impedance) of an interface between an a cathode and/or anode and a solid-state electrolyte. The interfacial layers can be used in, for example, solid-state batteries (e.g., solid-state, ion-conducting batteries).
Interfacial Atomistic Mechanisms of Lithium Metal Stripping and Plating in Solid–State Batteries
All-solid-state batteries based on a Li metal anode represent a promising next-generation energy storage system, but are currently limited by low current density and short cycle life. Further research to improve the Li metal anode is impeded by the lack of understanding in its failure mechanisms at lithium–solid interfaces, in particular, the fundamental atomistic processes responsible for interface failure. Here, using large-scale molecular dynamics simulations, the first atomistic modeling study of lithium stripping and plating on a solid electrolyte is performed by explicitly considering key fundamental atomistic processes and interface atomistic structures. In the simulations, the interface failure initiated with the formation of nano-sized pores, and how interface structures, lithium diffusion, adhesion energy, and applied pressure affect interface failure during Li cycling are observed. By systematically varying the parameters of solid-state lithium cells in the simulations, the parameter space of applied pressures and interfacial adhesion energies that inhibit interface failure during cycling are mapped to guide selection of solid-state cells. Furthermore, this study establishes the atomistic modeling for Li stripping and plating, and predicts optimal solid interfaces and new strategies for the future research and development of solid-state Li-metal batteries.