Engineering topics

Mock, W., Jr.

Publications and source records attributed to Mock, W., Jr..

8 records

NASA NTRS1985

An investigation of molecular structure of copolymers using positron annihilation spectroscopy

Positron lifetime measurements were made in copolyimides synthesized from linear 4,4 prime-bis(3,4-dicarboxyphenoxy) diphenylsulfide dianhydride (BDSDA)/4,4 prime-diaminodiphenyl (ODA) and BDSDA/1,3-diaminobenzene (m-phenylene diamine) homopolymers. The probability of positronium formation as well as its subsequent lifetime are lower in the BDSDA/ODA/MPD (50-50) copolyimide, indicating the presence of a transition molecular architecture characterized by higher electron density and stronger bonds which permit both chemical as well as physical entry of water molecules into it. The presence of this transition region imparts unique physical and mechanical properties to the copolyimide.

Singh, J. J.↗

NASA NTRS1984

Moisture dependence of positron annihilation spectra in nylon-6

Positron annihilation time spectra have been measured in nylon-6 samples as a function of their moisture content. The measured average long life component lifetime values are: 1722 + or - 47 ps (dry), 1676 + or - 40 ps (14.6 percent saturation value), 1719 + or - 26 ps (29.3 percent saturation value), 1720 + or - 35 ps (50 percent of saturation value), 1857 + or - 35 ps (78.1 percent saturation value), and 1936 + or - 57 ps (saturated). It appears that nylon-6 has a special affinity for water at low concentration levels where H2O molecules enter between the (C = O - H-N) chemical bonds between nylon molecular chains. As the water concentration increases beyond a critical level, nylon-6 specimens start trapping H2O molecules in other bond sites or potential wells. The trapped water increases the free volume in the test specimens and reduces Ps atom formation as well as its subsequent decay rate.

Singh, J. J.↗

NASA NTRS1984

Effect of metal ions on positron annihilation characteristics in metal ion containing epoxies

In the course of developing improved moisture-resistant epoxy resins, two different types of epoxy resins containing variable mole ratios of chromium ions per polymer repeat unit were developed. Positron annihilation characteristics have been investigated in these resins as a function of their metal ion content. In both cases, the presence of metal ions reduces the lifetime as well as the intensity of the long life component. The long life component intensity reduction is considerably more pronounced than the lifetime reduction. These results have been discussed in terms of increased unpaired electron density at Ps formation sites due to the presence of chromium ions in the matrix.

Singh, J. J.↗

NASA NTRS1982

Positron annihilation spectroscopy with magnetically analyzed beams

Lifetime measurements with magnetically analyzed positron beams were made in condensed media with uniform and non-uniform properties. As expected, the lifetime values with magnetically analyzed positron beams in uniform targets are similar to those obtained with conventional positron sources. The lifetime values with magnetically analyzed beams in targets which have non-uniform properties vary with positron energy and are different from the conventional positron source derived lifetime values in these targets.

Singh, J. J.↗

NASA NTRS1982

Positron lifetime studies in thermoplastic polyimide test specimens

Positron lifetime measurements were made in two thermoplastic polyimide materials recently developed at Langley. The long component lifetime values in polyimidesulfone samples are 847 + or - 81 Ps (dry) and 764 + or - 91 Ps (saturated). The corresponding values in LARC thermoplastic imides are 1080 + or - 139 Ps (dry) and 711 + or - 96 Ps (saturated). Clearly, the presence of moisture has greater effect on positron lifetime in LARC thermoplastic imides than in the case of polyimidesulfones. This result is consistent with the photomicrographic observations made on frozen water saturated specimens of these materials.

Singh, J. J.↗

NASA NTRS1982

Moisture dependence of positron annihilation rates in molecular substances

Positron annihilation rates have been studied in polymers and graphite-polymer composites as a function of their moisture content. The annihilation rates have been found to increase linearly with increasing moisture content in epoxies and polyamides, whereas no definite trends have been observed in polyimides. These experimental results have been used as the basis for the calculation of moisture content of several polymeric test specimens. For example, the directly measured moisture content of a Kevlar specimen was 45.5 + or - 5.0% of saturation value, whereas the moisture content on the basis of the decrease in positron lifetime was calculated to be 46.5 + or - 3.5%. Similarly, the directly measured moisture content of a graphite-epoxy composite (55 v/o fiber) was 19.2 + or - 0.6% of saturation value as opposed to a calculated value of 16.0 + or - 5.0%.

Singh, J. J.↗

NASA NTRS1980

Positron annihilation studies of moisture in graphite-reinforced composites

The positron lifetime technique of monitoring absorbed moisture is applied to several composites, including graphite/polymides which are candidates for high-temperature (over 260 C) applications. The experimental setup is a conventional fast-slow coincidence system wherein the positron lifetime is measured with respect to a reference time determined by the detection of a nuclear gamma ray emitted simultaneously with the positron. From the experiments, a rate of change of positron mean lifetime per unit mass of water can be determined for each type of specimen. Positron lifetime spectra are presented for a graphite/polyimide composite and for a pure polyimide.

Singh, J. J.↗

NASA NTRS1980

Moisture determination in composite materials using positron lifetime techniques

A technique was developed which has the potential of providing information on the moisture content as well as its depth in the specimen. This technique was based on the dependence of positron lifetime on the moisture content of the composite specimen. The positron lifetime technique of moisture determination and the results of the initial studies are described.

Singh, J. J.↗