Engineering topics

Mohagna J Pandya

Publications and source records attributed to Mohagna J Pandya.

8 records

NASA NTRS2022

USM3D Simulations for the Third AIAA Sonic Boom Prediction Workshop

The NASA USM3D flow solver was used to compute test cases for the Third AIAA Sonic Boom Prediction Workshop (SBPW3). The test cases included a nearfield biconvex shock-plume interaction wind tunnel model and the C608 Low Boom Flight Demonstrator. Numerical simulations were conducted on the mixed-element and tetrahedral grids provided by the workshop committee, as well as a family of grids generated by an in-house approach known as BoomGrid. The nearfield pressure signatures were extracted and propagated to the ground, and the perceived loudness levels on the ground were computed. The USM3D nearfield pressure signatures, corresponding ground signatures, and loudness levels on the ground were compared with that of mean values from other workshop participants. The effect of three flux-limiters on the accuracy of nearfield pressure signature prediction was investigated and results were compared with that of mean values from other workshop participants. The effect of using wall-function models for predicting nearfield pressure signatures was also evaluated. Results showed that the overpressure signatures extracted from the wall-modeled simulations and the wall-resolved simulations are in good agreement. The use of wall functions (wall-modeled simulations) allowed for approximately 23% savings in the time to solution and yielded comparable perceived loudness levels on the ground to the wall-resolved Reynolds-averaged Navier Stokes simulations.

Supersonics↗

NASA NTRS2021

Efficiency of Mixed-Element USM3D for Benchmark Three-Dimensional Flows

The unstructured, mixed-element, cell-centered, finite-volume flow solver USM3D is enhanced with new capabilities such as line generation for general unstructured grids and optimization of the iterative solver. The efficiency of the new developments is assessed in a massively parallel environment. The assessments are conducted using a baseline method and the recent hierarchical adaptive nonlinear iteration method framework. Three benchmark turbulent flows, namely, a subsonic separated flow around a three-dimensional hemisphere cylinder configuration, a transonic flow around the ONERA M6 wing, and a supersonic flow through a square duct are considered.

Mohagna J Pandya↗

NASA NTRSDate not supplied

USM3D Simulations for Third Sonic Boom Workshop

The NASA USM3D flow solver was used to compute test cases for the Third AIAA Sonic Boom Prediction Workshop (SBPW3). The test cases include a nearfield biconvex shock-plume interaction wind tunnel model, and the C608 Low Boom Flight Demonstrator. Numerical simulations were conducted on the mixed-element and tetrahedral grids provided by the workshop committee, as well as a family of grids generated by an in-house approach for sonic boom analyses known as BoomGrid. The near-field pressure signatures were extracted, propagated to the ground and the perceived loudness levels on the ground were computed. The USM3D near-field pressure signatures, corresponding ground signatures, and loudness levels on the ground are compared with that of mean values from other workshop participants. The effect of three flux-limiters on the accuracy of near-field pressure signatures prediction was investigated and results are compared with that of mean values from other workshop participants. The effect of using wall function grids in accurately predicting near-field pressure signatures was also evaluated.

Supersonics↗

NASA NTRSDate not supplied

Mixed-element USM3D Contributions to the 4th AIAA High-Lift Prediction Workshop

This paper discusses results of the mixed-element USM3D (USM3D-ME) simulations performed for the 4th AIAA High-Lift Prediction Workshop. The workshop was separated into six Technical Focus Groups to investigate the impact of geometry modeling, grid, and computational methods for predicting high lift flows. This work was performed under the Fixed Grid RANS Technical Focus Group. The primary geometry selected for the workshop was the High-Lift Common Research Model. The performed simulations included a flap deflection study and both a grid refinement study and pitch sweep for the nominal flap deflection configuration. The results show that USM3D-ME RANS solutions, generally, tends to underpredict the lift coefficient and to predict a less negative pitching moment relative to the experimental data. The predicted drag coefficient values agree better with experiment for smaller angles of attack but were observed to be larger than experiment for the largest angle of attack simulated. The results of the grid refinement study demonstrated a lack of grid convergence for the provided grid family. The results of the grid refinement study are consistent with the submissions to the Fixed Grid and Mesh Adaptation Technical Focus Groups. Grid convergence for the provided grid family remains elusive for the international community. A 2D Multielement Airfoil configuration was included to enable a turbulence model verification study, which illustrated favorable agreement between USM3D-ME and the solutions provided by other flow solvers.

CFD↗

NASA NTRSDate not supplied

USM3D-ME Revised SA-neg Implementation and Assessment for Seventh Drag Prediction Workshop Solutions

Simulations performed by an unstructured-grid, cell-centered, finite-volume, mixed-element flow solver USM3D-MEwere presented at the Seventh Drag Prediction Workshop (DPW-7). Reynolds-averaged Navier-Stokes (RANS) solutions for the NASA high-speed common research model wing-body configuration were computed using a new implementation of the negative variant of the Spalart-Allmaras turbulence model (SA-neg) with hierarchical adaptive nonlinear iteration method (HANIM).ThisUSM3D-ME enhancement improved efficiency and robustness of RANS solutions resulting in fast iterative convergence to machine zero residuals on mixed-element unstructured grids provided by the DPW-7 organizing committee. This paper presents theoretical foundations for the new implementation of the SA-neg model and analyzesUSM3D-ME solutions for flow conditions corresponding to the required DPW-7 cases.

Boris Diskin↗

NASA NTRSDate not supplied

High-Fidelity CFD Verification Workshop 2024 Summary: Spalart-Allmaras QCR2000-R Turbulence Model

This paper summarizes solutions submitted for the Reynolds-averaged Navier-Stokes (RANS) test suite of the High-Fidelity CFD Verification Workshop. The goal of the workshop is to establish standards for verification of computational fluid dynamics (CFD) approaches to simulations of steady and unsteady turbulent flows. The RANS verification studies focus on a one-equation Spalart-Allmaras model with quadratic constitutive relation and rotation correction, SA-neg-QCR2000-R. The verification test cases are a two-dimensional subsonic flow around a Joukowski airfoil, a three-dimensional subsonic flow around an extruded NACA 0012 wing in a tunnel, and a subsonic flow around a wing-body configuration developed for verification of solvers participating in the 5 𝑡 ℎ High-Lift Prediction Workshop. The turbulencemodel formulation, geometry, flow conditions, grids, and reference solutions are described in detail. Solutions for the test cases are computed by seven established CFD solvers on adaptedand fixed-grid families using different discretization approaches. While some noticeable differences between solutions remain, the results achieved by contributing solvers show that different solutions computed for the same RANS model on different grid families can converge to a common limit with grid refinement. The apparent requirements for grid convergence are a well designed family of grids that provide sufficient resolution in important areas and a strong solver capable of deep iterative convergence on each grid. For each test case in the study, the variation between aerodynamic forces computed by different solvers on the finest grids of different families is less than 2%.

Boris Diskin↗

NASA NTRSDate not supplied

USM3D-ME Contributions to the 5th AIAA High Lift Prediction Workshop

This paper presents the results of Reynolds-averaged Navier-Stokes (RANS) simulations conducted by NASA’s flow solver, mixed-element USM3D (USM3D-ME), for the 5th AIAA High-Lift Prediction Workshop. As part of the Fixed-Grid RANS Technology Focus Group (TFG), these simulations were performed to assess the accuracy and efficiency of the USM3D-ME solutions in predicting high-lift flows. The High-Lift Common Research Model (CRM-HL) served as the primary geometry. Several CRM-HL configurations were used for three case studies: a verification study (Case 1), a configuration buildup study (Case 2), and a Reynolds-number variation study (Case 3). Overall, USM3D-ME RANS results aligned with the solutions selected by the Fixed-Grid RANS TFG and available wind tunnel data Simulations for Cases 1 and Configuration 2.1 achieved machine-zero residual convergence, with aerodynamic coefficients converging to steady-state values. However, Configurations 2.2-2.4 and Case 3 encountered iterative- and grid-convergence challenges, particularly at high angles of attack. Compared with the experimental data available for Configurations 2.2-2.4, close agreement was demonstrated at low angles of attack. However, for angles of attack approaching the maximum lift conditions, the predicted lift coefficient and pitching moment deviated from experimental values. The drag-coefficient predictions were in a relatively good agreement, however, slight overpredictions were observed at the highest angle of attack corresponding to the maximum-lift condition. Although iterative convergence for Configurations 2.2-2.4 at high angles of attack remains a persistent challenge, averaging aerodynamic coefficients over the last 5000 iterations yielded satisfactory agreement with the available wind tunnel experimental data. During the workshop, the lack of iterative convergence was attributed to the vortex structures emanating from the slat brackets. To investigate this issue further, post-workshop simulations were conducted on Configuration 2.2. In one study, RANS simulations were performed on a simplified geometry with the slat brackets removed. The second study focused on performing URANS simulations on the original Configuration 2.2 geometry. Preliminary results from both studies are presented and compared with wind tunnel data for Configuration 2.2. Consistent with the findings of other participants in the Fixed-Grid RANS TFG, this study emphasizes the necessity for further exploration and advancement in RANS technology for predicting high-lift flows.

CFD↗

NASA NTRSDate not supplied

USM3D-ME Contributions to the 5th AIAA High Lift Prediction Workshop

This paper presents the results of Reynolds-averaged Navier-Stokes (RANS) simulations conducted by the NASA flow solver, mixed-element USM3D (USM3D-ME), for the 5th AIAA High-Lift Prediction Workshop. As part of the Fixed-Grid RANS Technology Focus Group (TFG), these simulations were performed to assess the accuracy and efficiency of the USM3D-ME solutions in predicting high-lift flows. The High-Lift Common Research Model (CRM-HL) served as the primary geometry. Several CRM-HL configurations were used for three case studies: a verification study (Case 1), a configuration buildup study (Case 2), and a Reynolds-number variation study (Case 3). Overall, USM3D-ME RANS results aligned with the solutions selected by the Fixed-Grid RANS TFG and available wind tunnel data. Simulations for Case 1 and Configuration 2.1 achieved machine-zero residual convergence, with aerodynamic coefficients converging to steady-state values. However, Configurations 2.2-2.4 and Case 3 encountered iterative- and grid-convergence challenges, particularly at high angles of attack. Compared with the experimental data available for Configurations 2.2-2.4, close agreement was demonstrated at low angles of attack. However, for angles of attack approaching the maximum lift conditions, the predicted lift coefficient and pitching moment deviated from experimental values. The drag-coefficient predictions were in relatively good agreement, however, slight overpredictions were observed at the highest angle of attack corresponding to the maximum-lift condition. Although iterative convergence for Configurations 2.2-2.4 at high angles of attack remains a persistent challenge, averaging aerodynamic coefficients over the last 5000 iterations yielded satisfactory agreement with the available wind tunnel experimental data. During the workshop, the lack of iterative convergence was attributed to the vortex structures emanating from the slat brackets. To investigate this issue further, post-workshop simulations were conducted on Configuration 2.2. In one study, RANS simulations were performed on a simplified geometry with the slat brackets removed. The second study focused on performing unsteady RANS (URANS) simulations on the original Configuration 2.2 geometry. Preliminary results from both studies are presented and compared with wind tunnel data for Configuration 2.2. Consistent with the findings of other participants in the Fixed-Grid RANS TFG, this study emphasizes the necessity for further exploration and advancement in RANS technology for predicting high-lift flows.

Aerodynamics↗