Creep-induced elemental redistribution at grain boundaries of 304L stainless steel – An experimental evidence for diffusional creep mechanisms
Not Available
Engineering topics
Publications and source records attributed to Mohale, Ninad.
Not Available
The Advanced Materials and Manufacturing Technologies (AMMT) Program focuses on advancing materials and manufacturing techniques for nuclear energy applications, particularly in the qualification of materials for high-temperature structural use. This report presents work on refining the creep testing of small specimen geometries. Efforts include the development of a new specimen geometry for sub-sized specimens, which were subjected to uniaxial creep tests. The results contribute to the understanding of material behavior under stress at elevated temperatures and offer potential improvements in creep data collection methods. These findings support ongoing advancements in material qualification processes essential for nuclear reactor applications.
This report provides the mechanical test data of laser powder bed fusion (LPBF) 316H stainless steel (SS) collected during Fiscal Year 2024 (FY 24) under the US Department of Energy, Office of Nuclear Energy’s Advanced Materials and Manufacturing Technologies program, along with the current state of microstructural-based understandings of the behaviors. Materials with variabilities in manufacturing site, machine, laser parameters, powder chemistry, porosity, specimen geometry and heat treatment were tested in high-temperature tension, creep, fatigue and creep-fatigue. Electron microscopy and optical microscopy were performed on selected materials before and after the tests to provide microstructural-based understandings to the mechanical behavior. It was discovered that the as-built (AB) and stress-relieved (SR) materials exhibit similar behaviors in tension and creep, as do the solution-annealed (SA) and hot-isostatic pressed (HIP) materials. The AB and SR materials are softer but more ductile than the SA and HIP materials in tension. In creep, the LPBF materials have comparable rupture times but lower rupture strains compared to the wrought materials. The AB and SR materials have low creep rupture strains (<10%) when tested at 720°C and 800°C, while the SA and HIP materials are much more ductile. The LPBF materials exhibit large scatter in fatigue and creep-fatigue lives. The cyclic lives of creep-fatigue tests are lower than those of fatigue tests. In fatigue and creep-fatigue, SR materials outperform SA materials. A common observation from the cyclic tests is that, given the same post-build heat treatment, a lower initial peak stress generally results in a longer cyclic life regardless of hold time. It was also discovered that the batch variation can be more impactful than heat treatment, as demonstrated by the overall better performance of one batch of material than another, regardless of the heat treatment. The results provided insights into how different factors impact the behaviors of LPBF 316H SS. An outlook to FY 25 work scope is provided.
When creep testing is repeated on samples of the same alloy under the same parametric conditions (i.e., stress and temperature), the resulting strain/time curves can vary from each other considerably as shown in Figure 1 [1]. The time required to creep test a material to rupture can extend to the order of years. Because of this, a numerical model that can quickly analyze the incomplete results of an ongoing experiment to predict 1) the incomplete portion of the strain/time curve leading up to the rupture point and 2) the rupture point itself would be of great utility to the materials community. Such a model has the potential to save 1) the time required to finish running the experiment to rupture 2) the associated monetary cost of finishing said experiment. Furthermore, it would be advantageous if the predictive model could give a parametric function modeling strain/time curves for material scientists to investigate the impact of the temperature and stress parameters on the resulting creep behavior. This work introduces a piecewise symbolic regression algorithm to predict the remainder of the strain/time curve. Preliminary results show good model performance.
The development of compact heat exchangers (CHXs) has gained increasing interest in many industries owing to their high thermal efficiency and reduced size. Diffusion bonding (DB) is an advantageous technique for fabricating CHXs. Alloy 617 is a candidate for manufacturing CHXs for high-temperature advanced nuclear reactors due to its elevated-temperature properties. Previous endeavors in DB of Alloy 617 were conducted by hot pressing (HP), which reported precipitates at the diffusion-bond interface, limited grain boundary (GB) migration, and significantly reduced high-temperature mechanical properties. To overcome these challenges, this study investigated DB of Alloy 617 using electric field-assisted sintering (EFAS). Stacks composed of three sheets were bonded with EFAS using different temperatures, pressures, and hold times. DB using HP as the zero-current analog of EFAS was also performed for comparison. The result shows that Cr- and Mo-rich precipitates were formed at the interface of the hot-pressed samples. The electric current and temperature in EFAS play a significant role in precipitation and GB migration. The electric current coupled with correct temperatures can effectively prevent precipitate formation at the interface and achieve excellent GB migration. Nanoscale Al-rich oxide was formed at the interface of the samples made by both HP and EFAS, but grain boundaries can ignore the nanoscale Al-oxide and migrate across the interface. The temperature, pressure, and hold time also affected diffusion. The temperature is a prerequisite for a successful GB migration, and GB migration can be enhanced by increasing pressure and hold time.
This report discusses work conducted at Idaho National Laboratory in fiscal year 2022 associated with the precipitates in Alloy 709 (A709). The purpose of this work is to support the development of the A709 Code Cases to qualify A709 in Section III, Division 5 of the American Society of Mechanical Engineers Boiler and Pressure Vessel Code. This would permit the use of A709 for elevated-temperature nuclear construction. This work encompassed two broad goals. The first goal was to understand the microstructure of the second commercial heat of plate A709 purchased through the Advanced Reactors Technologies Program in both the solution-annealed and precipitation-treated conditions. Transmission electron microscopy was utilized to characterize these microstructures. Direct comparisons were then made between the solution-annealed and precipitation-treated conditions as well as between the first and second commercial heats of plate A709. The second goal was to understand the impact of variations in the time and temperature of the precipitation treatment on the properties of A709. The precipitation treatment temperature was varied from 750°C to 800°C for times ranging from 3 hours to 30 hours. The hardness of each precipitation treatment variation was measured. All of the precipitation treatment variations investigated besides a specimen from the second commercial heat of plate A709 precipitation treated at 800? for 9 hours met the room-temperature hardness requirement specified in ASTM A213 and SA-213 for UNS S31025. The hardness measured for the specimen from the second commercial heat of plate A709 that was precipitation treated at 800? for 9 hours is considered an outlier. The next step is to look at the extremes of the precipitation treatment variations investigated and conduct elevated-temperature mechanical testing. The purpose of this testing would be to assess if these time and temperature variations have any impact on the mechanical performance.
Nickel-base superalloys that are in service for long periods of time in fossil energy powerplants have microstructures that evolve with time. The strengthening gamma prime phase coarsens, and in some alloys, a new phase (eta) forms at grain boundaries, and its effect on creep performance is not fully understood.