Engineering topics
Moldovan, N
Publications and source records attributed to Moldovan, N.
Development of optics for x-ray phase-contrast imaging of high energy density plasmas
Phase-contrast or refraction-enhanced x-ray radiography can be useful for the diagnostic of low-Z high energy density plasmas, such as imploding inertial confinement fusion (ICF) pellets, due to its sensitivity to density gradients. To separate and quantify the absorption and refraction contributions to x-ray images, methods based on microperiodic optics, such as shearing interferometry, can be used. To enable applying such methods with the energetic x rays needed for ICF radiography, we investigate a new type of optics consisting of grazing incidence microperiodic mirrors. Using such mirrors, efficient phase-contrast imaging systems could be built for energies up to {approx}100 keV. In addition, a simple lithographic method is proposed for the production of the microperiodic x-ray mirrors based on the difference in the total reflection between a low-Z substrate and a high-Z film. Prototype mirrors fabricated with this method show promising characteristics in laboratory tests.
Prevention of nanoscale wear in atomic force microscopy through the use of monolithic ultrananocrystaline diamond probes.
Nanoscale wear is a key limitation of conventional atomic force microscopy (AFM) probes that results in decreased resolution, accuracy, and reproducibility in probe-based imaging, writing, measurement, and nanomanufacturing applications. Diamond is potentially an ideal probe material due to its unrivaled hardness and stiffness, its low friction and wear, and its chemical inertness. However, the manufacture of monolithic diamond probes with consistently shaped small-radius tips has not been previously achieved. The first wafer-level fabrication of monolithic ultrananocrystalline diamond (UNCD) probes with <5-nm grain sizes and smooth tips with radii of 30-40 nm is reported, which are obtained through a combination of microfabrication and hot-filament chemical vapor deposition. Their nanoscale wear resistance under contact-mode scanning conditions is compared with that of conventional silicon nitride (SiN{sub x}) probes of similar geometry at two different relative humidity levels ({approx}15 and {approx}70%). While SiN{sub x} probes exhibit significant wear that further increases with humidity, UNCD probes show little measurable wear. The only significant degradation of the UNCD probes observed in one case is associated with removal of the initial seed layer of the UNCD film. The results show the potential of a new material for AFM probes and demonstrate a systematic approach to studying wear at the nanoscale.
Nanofabrication of sharp diamond tips by e-beam lithography and inductively coupled plasma reactive ion etching.
Ultrasharp diamond tips make excellent atomic force microscopy probes, field emitters, and abrasive articles due to diamond's outstanding physical properties, i.e., hardness, low friction coefficient, low work function, and toughness. Sharp diamond tips are currently fabricated as individual tips or arrays by three principal methods: (1) focused ion beam milling and gluing onto a cantilever of individual diamond tips, (2) coating silicon tips with diamond films, or (3) molding diamond into grooves etched in a sacrificial substrate, bonding the sacrificial substrate to another substrate or electrodepositing of a handling chip, followed by dissolution of the sacrificial substrate. The first method is tedious and serial in nature but does produce very sharp tips, the second method results in tips whose radius is limited by the thickness of the diamond coating, while the third method involves a costly bonding and release process and difficulties in thoroughly filling the high aspect ratio apex of molding grooves with diamond at the nanoscale. To overcome the difficulties with these existing methods, this article reports on the feasibility of the fabrication of sharp diamond tips by direct etching of ultrananocrystalline diamond (UNCD{reg_sign}) as a starting and structural material. The UNCD is reactive ion etched using a cap-precursor-mask scheme. An optimized etching recipe demonstrates the formation of ultrasharp diamond tips ({approx} 10 nm tip radius) with etch rates of 650 nm/min.
Freestanding diffractive optical elements as light extractors for burning plasma experiments
Optical diagnostics will be critical for the operation and performance assessment of burning plasma experiments, such as ITER. At the same time, extracting light for these diagnostics with reflective mirrors becomes difficult in the burning plasma environment due to the deleterious effects of the prolonged exposure on plasma and nuclear radiations. As an alternative, we explore the possibility to use freestanding diffractive optical elements, such as transmission gratings and zone plates, as light extractors. Since in diffractive systems, light is deflected by periodic slits rather than by a surface, these may withstand plasma exposure with less degradation of their optical properties. To investigate this possibility, we developed freestanding transmission gratings for the visible range and exposed them to conditions resembling (or even exceeding) those expected for the ITER 'first mirrors.' The results of this study indicate that the gratings can withstand high heat fluxes and plasma and energetic radiation bombardment. Additionally, in contrast to the reflective elements, the extraction efficiency of diffractive elements may even improve with plasma exposure, which is possibly due to the shaping and thinning of the grating bars by plasma erosion. Moreover, in tightly collimated configurations, even very thin gratings can be used to extract light from hot fusion plasmas, as demonstrated by our tests of an extreme ultraviolet extractor at the National Spherical Torus Experiment.