Search NASA⌕ Search

Engineering topics

Monazam, Esmail R.

Publications and source records attributed to Monazam, Esmail R..

At least 19 records

Operational Performance Characteristics of an Aerated L-valve Operated Within a Closed Circulating Fluidized Bed Loop

An experimental study was conducted in a large scale circulating fluidized bed (0.3 m diameter ×15.5 m tall) equipped with nonmechanical L-valve (0.25 m diameter ×1.52 m long) varying the riser superficial gas velocity (U g ), bed inventory (m), L-valve aeration velocity (U Lvalve ) and standpipe aeration velocity (U move ). The effects of these operational parameters on pressure drop were investigated in each of the different components in the CFB and on the solid circulation rate with two different Group B particles (180 μm glass bead and 750 μm phosphorescent polyethylene beads, PPE). Tests were carried out at ambient temperature and pressure conditions using air as the fluidization gas. The operating parameters were shown to significantly affect pressure drops across various sections of the CFB due to redistribution of solids within the system. The pressure drop in the horizontal section of the L-valve was affected by aeration rates in addition to the solid flow rate reported in previous studies of smaller L-valves without aeration. A new dimensionless semi-empirical correlation was able to explain > 98% of the variance between pressure drop across the horizontal section of the L-valve and operating parameters for these Group B particles. The results of present study indicated that the nonmechanical L-valve cannot be isolated from the CFB system for performance evaluation.

Monazam, Esmail R.↗

Attrition of hematite particles for chemical looping combustion in a conical jet cup

The attrition of hematite particles for use in the chemical looping combustion process was investigated using a cold flow jet cup test. Jet cup attrition experiments are commonly used for bulk attrition testing of fluidized bed catalyst. The results indicate that the particle attrition in the jet cup cold flow experiments arises from surface abrasion due to particle-particle and particle-wall interactions. Experiments indicate that the measured cumulative mass loss increases with attrition time. However, the attrition rate decreases sharply at the early stage of attrition, and gradually, the rate decline slows and approaches a constant value with increasing attrition time. Furthermore, the influence of inlet gas velocity and solid inventory is discussed. As inlet gas velocities increase, the measured cumulative mass loss also increases. However, as the solid inventory increases, the cumulative mass loss decreases. The results also show that the jet cup experiments quantitatively compare with low magnitude tangential forces which is an indication of attrition through abrasion as the primary mechanism. It is determined through particle size distributions before and after which show a small shift of the main peaks with no peak broadening while producing a small number of fines. By using the mass of abraded fines and the widely-used Archard model for abrasive attrition, the specific wear rate coefficient can be predicted as a function of time. The wear coefficient calculation further identifies that the abrasion mechanism as the primary mechanism of attrition.

42 ENGINEERING↗

Hydrogen Production by Steam Oxidation of Reduced CaFe 2 O 4 during Chemical Looping Coal Gasification: Equilibrium and Kinetic Analysis

CaFe 2 O 4 reduced during chemical looping coal gasification can be oxidized with steam for production of hydrogen. The conversion and equilibrium data of the oxidation of reduced CaFe 2 O 4 with steam were analyzed using steam concentrations of 10–25 vol % with a balance of helium and the temperature range of 1023–1123 K. Experimental data were evaluated to characterize H 2 production rates and oxidation isotherms. The film diffusion was the controlling step for the oxygen uptake process, and its parameters were determined on the basis of the uptake rate model. The steady-state oxygen uptake data were also evaluated with Langmuir, Temkin, Freundlich, and Dubinin–Radushkevich isotherms. The Langmuir isotherm model correlated the oxidation isotherms best, and the peak uptake capacity decreased with increasing temperatures, which suggests an exothermic process. In conclusion, the negative Gibbs free energy values (–Δ G °) implied the spontaneous nature of the uptake process at 1023–1123 K.

01 COAL, LIGNITE, AND PEAT↗

Analysis of Solids Flow Rate through Nonmechanical L-Valve in an Industrial-Scale Circulating Fluidized Bed Using Group B Particles

A series of statistically designed experiments were conducted using two different Geldart Group B particles in a 0.3 m diameter circulating fluidized bed (CFB) cold model to evaluate the nonmechanical L-valve for controlling the solids flow rate. The objective of this study was to investigate the effects of standpipe aeration, L-valve aeration, solids inventory, and superficial gas velocity through the riser on the solids flow rate. A stochastic correlation was developed for calculating the solid flow rate as a function of these variables. It was found that the solid flow rate increased directly proportional to each of these variables. Dimensional analysis was used to generate an expression for the solids turnover ratio. The model developed in the present study is intended to simulate flow in the present CFB loop. In conclusion, it is not intended for scale-up and will probably not apply for alternative CFB loops with different geometries/pressure balance conditions.

42 ENGINEERING↗

Insights into the Adsorption of Carbon Dioxide in the Presence of Water Vapor Utilizing a Low Molecular Weight Polyethylenimine-Impregnated CARiACT Silica Sorbent

Thermogravimetric analysis was employed to investigate the CO 2 and H 2 O adsorption rates and water vapor equilibrium on anhydrous and pre-hydrate linear polyethylenimine (LPEI) sorbent impregnated within a commercially functional CARiACT G10 (HPV) silica support. Water vapor experiments utilizing specific humidity of 2%, 8%, and 16% in contact with an anhydrous PEI sorbent resulted in proportional quantities of water vapor uptake. Subsequently, both anhydrous and pre-hydrated PEI-impregnated sorbents were made available to identical humidified gaseous streams containing a CO 2 concentration of 10% at 60oC. CO 2 capacity increased dramatically in the presence of different levels of humidity. Various kinetic models were systematically employed to interpret the experimental data including single and multiple-step models. The rate data was best represented by a reaction mechanism pathway involving the interplay of CO 2 with PEI-impregnated sorbents exhibited a quick adsorption phase followed by a slow approach to equilibrium. Moreover, a phenomenological rate model was developed to describe the dynamic H 2 O and CO 2 uptakes at specific humidity levels studied. The kinetic study showed good agreement with experimental data. Furthermore, the effects observed during the adsorption and hydration are shown to be complementary to known chemical and physical transformations within the polyethylenimine’s macromolecule.

20 FOSSIL-FUELED POWER PLANTS↗

Minimum spouting velocity of flat-base spouted fluid bed

Experiments were performed on spout characteristics of a cylindrical spout-fluidized bed (I.D. = 10 cm) with different static heights and two materials (Al 2 O 3 and high density polyethylene). Results of minimum spouting velocity obtained in this study were compared with reported correlations for both spouted and spout-fluidized beds. Considerable discrepancies were found between the values obtained using different model equations as well as with respect to experimental results. Based on the Mathur–Gishler correlation, a new correlation is proposed for calculating the minimum spouting velocity that introduces the ratio U/U mf . It was found that the minimum spouting velocity decreases with increasing fluidizing gas velocity (U/U mf ). The pressure drop at the point of minimum spouting velocity is also correlated using this dimensionless group and is presented in this work. Finally, this investigation demonstrates that the use of correlations reported in the literature that focus primarily on conical bottom spouted beds are not applicable to flat-bottom spouted and spout-fluidized beds.

42 ENGINEERING↗

Analysis of maximum pressure drop for a flat-base spouted fluid bed

For design purposes of the blower power requirements during startup of a spouting bed process, knowledge of the maximum pressure drop across a spouting bed at the onset of spouting is required. A survey of the literature for this information lead to only a few correlations which required information from a spouting bed test to be applicable. Therefore, an experimental investigation of this pressure drop and its associated superficial gas velocity in a flat based spouted bed operating with and without fluidization has been conducted. Measurements were performed using a 10 cm cylindrical bed with different static bed heights and two Geldard group B particles (Al2O3 and HDPE). The results show that the taller static bed height creates a larger maximum pressure drop across the bed, as expected. The maximum pressure drop also increases with increasing fluidized gas velocity. In conclusion, the evolution of maximum pressure drop and its velocity were evaluated and a correlation for the maximum pressure drop and its corresponding velocity for spouted and spouted fluid beds were obtained.

42 ENGINEERING↗

The effect of riser end geometry on gas-solid hydrodynamics in a CFB riser operating in the core annular and dilute homogeneous flow regimes

Riser hydrodynamics are a function of the flow rates of gas and solids as well as the exit geometry, particularly when operated above the upper transport velocity. This work compares the exit voidage for multiple geometries and two different solids: Geldart group A glass beads and Geldart group B coke. Geometries were changed by modifying the volume of an abrupt T-shaped exit above the lateral riser exit. This was accomplished by positioning a plunger at various heights above the exit from zero to 0.38 m. A dimensionless expression used to predict smooth exit voidage was modified to account for the effect of the depth of the blind-T. The new correlation contains the solids-gas load ratio, solids-to-gas density ratio, bed-to-particle diameter ratio, gas Reynolds Number, as well as a term for the exit geometry. This study also found that there was a minimum riser roof height above the blind-T exit beyond which the riser exit voidage was not affected by the exit geometry. A correlation for this minimum riser roof height has also been developed in this study. This study covered riser superficial gas velocities of 4.35 to 7.7 m/s and solids circulation rates of 1.3 to 11.5 kg/s.

01 COAL, LIGNITE, AND PEAT↗

Development and Validation of a Dynamic Response Model for a Cold Flow Circulating Fluidized Bed

A dynamic response model has been created of the Cold Flow Circulating Fluidized Bed at NETL in Morgantown, WV. The model is considered dynamic, as opposed to steady state, because it is used to predict the transient responses of gas and solids flows throughout the unit as process conditions vary. The model was built in ProTrax with Advanced Continuous Simulation Language (ACSL) custom code. Dynamic experiments, varying both gas and solids flows, in the CFB unit have been used to validate the accuracy of the model. The advantage of this model is its utility in predicting gas hold up and solids flow throughout the unit during transitions of process conditions. Accurate predictions of these phenomena are important in process control and optimization. The dynamic experiments used in validating the model include modulations of the system pressure, move air (solids flow), and riser gas velocity with step and sinusoidal changes.

01 COAL, LIGNITE, AND PEAT↗

Modeling of the Reduction of Hematite in the Chemical Looping Combustion of Methane using Barracuda

Chemical looping combustion is a promising technology for the capture of CO 2 involving reduction and oxidation of materials known as oxygen carriers. One particular carrier is hematite as it is readily available and relatively inexpensive as well as being non-toxic. The objective of this paper is to present a new particle model and reaction kinetics that can be applied to Barracuda® simulations of the fuel reactor. This was done since Barracuda does not allow for the JMA (nucleation and growth) type kinetics that were developed from analytical study the results from TGA and fixed bed experiments. This paper summarizes the analytical analysis of the fixed bed reduction experiments conducted in a cycling fixed bed reactor and subsequently modeled with Barracuda® CFD software to develop the new model. The experiments were conducted using nominally 1000 g of hematite material. The cyclic processing began with the reduction step then proceeded to the oxidation step repeating this analysis for several cycles (5 to 10). The effects of fuel partial pressure (8.4, 7.2 and 5 mole %) on the conversion were investigated. The JMA analysis assumed the reactions to occur in the shell surrounding the particle grains with diffusion of oxygen to the grain surface from the core. In contrast, working with the particle kinetics allowed in Barracuda®, the reactions occur with different hematite species (surface and core) homogeneously mixed. Therefore it is necessary to develop a new particle model with the rates being related to the amount of reactant (surface or core) in the particle. This paper presents the development of such a particle model and compares the results with experimental results.

01 COAL, LIGNITE, AND PEAT↗

Reaction Kinetics of Mixed CuO–Fe 2 O 3 with Methane as Oxygen Carriers for Chemical Looping Combustion

Reduction kinetics of alumina supported mixed Cu–ferrite oxide by methane was investigated for chemical looping combustion by the thermogravimetric analyzer (TGA) in the temperature range of 750–900 °C using continuous streams of 10%, 20%, and 30% CH 4 concentrations balanced by helium. The rate of reduction was determined by weight change. The variations of activation energies and n values (JMA exponent) during the reduction conversion indicate that the methane combustion with CuO and Fe 2 O 3 proceeds via a multistage reaction process. A kinetic model based on three parallel reactions was applied to the reduction data. In conclusion, the analysis of reduction showed that three reduction steps proceed simultaneously with the activation energies of 55.32 ± 3.11, 70.0 ± 2.0, and 165.0 ± 5.4 kJ/mol, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Analysis of fixed bed data for the extraction of a rate mechanism for the reaction of hematite with methane

In this study, chemical looping combustion is a promising technology for the capture of CO 2 involving redox materials as oxygen carriers. The effects of reduction conditions, namely, temperature and fuel partial pressure on the conversion products are investigated. The experiments were conducted in a laboratory fixed-bed reactor that was operated cyclically with alternating reduction and oxidation periods. Reactions are assumed to occur in the shell surrounding the particle grains with diffusion of oxygen to the surface from the grain core. Activation energies for the shell and core reactions range from 9 to 209 kJ/mol depending on the reaction step.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fixed bed reduction of hematite under alternating reduction and oxidation cycles

The rate of the reduction reaction of a low cost natural hematite oxygen carrier for chemical looping combustion was investigated in a fixed bed reactor where hematite samples of about 1 kg were exposed to a flowing stream of methane and argon. The investigation aims to develop understanding of the factors that govern the rate of reduction with in larger reactors as compared to mostly TGA investigations in the literature. Comparison of the experimental data with a model indicated that reaction between the methane and the iron oxide shows multi-step reactions. The analysis also shows that the conversion occurs with a process that likely consumes all the oxygen close to the surface of the hematite particles and another process that is likely controlled by the diffusion of oxygen to the surface of the particles. Additional analysis shows that the thickness of the fast layer is on the order of 8 unit crystals. As a result, this is about 0.4% of the hematite; however, it comprises about 20 to 25% of the conversion for the 10 min reduction cycle.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗