Search NASA⌕ Search

Engineering topics

Monroe, Graham

Publications and source records attributed to Monroe, Graham.

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Techno‐Economic Analysis of Additively‐Manufactured Wind Turbine Blade Tips That Enable Technology Integration

The Additively‐Manufactured, System‐Integrated Tip (AMSIT) project is leveraging the flexibility of 3D printing to integrate several technologies in a wind turbine blade tip, while reducing the levelized cost of electricity (LCOE) produced. The design integration is demonstrated for a 200‐kW–scale turbine with 13‐m blades, with the outer 15% of the blade replaced with a 3D‐printed design. Aerodynamic performance is enhanced without increasing swept area through inclusion of a winglet and surface texturing, both challenging for traditional manufacturing. Longevity and durability are improved through integrated lightning and leading edge erosion protection. Increased power, reduced repair frequency, and ease of repair through blade modularity all contribute to reduced LCOE. The analysis is also extended to modern MW‐scale designs to estimate the impact of the technology at scale, demonstrating the potential to reduce LCOE significantly for modern onshore turbines, with even higher potential savings offshore.

3D printing↗
DOE OSTI2022

Computational Fluid Dynamics and Heat Transfer Modeling of a Dimpled Heat Exchanger

Multiphysics and analytical calculations were conducted for a heat exchanger with passive, natural circulation flow. A glycol/water working fluid convects the heat to a dimpled heat exchanger shell, which subsequently transfers the heat to the soil, which acts as the ultimate heat sink. Because the system is fully-passive, it is not subject to the expenses, maintenance, and mechanical breakdowns associated with moving parts. Density, heat capacity, and thermal conductivity material properties were measured for various soil samples, and subsequently included as input for the soil heat conduction model. The soil model was coupled to a computational fluid dynamics (CFD) heat exchanger model that included the dynamic Smagorinsky large eddy simulation and k- omega turbulence models. The analysis showed that the fluid dynamics and heat transfer models worked properly, albeit at a slow pace. Nevertheless, the coupled CFD/heat conduction simulation ran long enough to determine a key parameter—the amount of heat conducted from the heat exchanger to the ground. This unique performance value, along with experimental data, was used as input for stand-alone, fast-running CFD models, as well as boundaries to obtain solutions to partial differential equations for soil heat conduction.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Fractal-Fin, Dimpled Solar Heat Collector with Solar Glaze

Exterior solar glaze was added to a 3 foot x 3 foot x 3 foot aluminum solar collector that had six triangular dimpled fins for enhanced heat transfer. The interior vertical wall on the south side was also dimpled. The solar glaze was added to compare its solar collection performance with unglazed solar collector experiments conducted at Sandia in 2021. The east, west, front, and top sides of the solar collector were encased with solar glaze glass. Because the solar incident heat on the north and bottom sides was minimal, they were insulated to retain the heat that was collected by the other four sides. The advantages of the solar glaze include the entrapment of more solar heat, as well as insulation from the wind. The disadvantages are that it increases the cost of the solar collector and has fragile structural properties when compared to the aluminum walls. Nevertheless, prior to conducting experiments with the glazed solar collector, it was not clear if the benefits outweighed the disadvantages. These issues are addressed herein, with the conclusion that the additional amount of heat collected by the glaze justifies the additional cost. The solar collector glaze design, experimental data, and costs and benefits are documented in this report.

14 SOLAR ENERGY↗
DOE OSTI2020

Metal Alloy and RHEA Additive Manufacturing for Nuclear Energy and Aerospace Applications

An open-literature search was conducted to consider the current status of the additive manufacturing (AM) industry with respect to metal alloys and refractory high entropy alloys (RHEAs). Key areas of interest include methodologies and applications that are suitable for the nuclear and aerospace industries, as well as other industrial applications. We investigated various promising 3D metal technologies, with emphasis on cost, operation, throughput, maintenance, and output volume size. In addition, technical issues and the current status of the metal printing market are summarized. The project scope also included the manufacturing of open-literature RHEA test coupons at Sandia's laser engineered net shape (LENS) machine.

36 MATERIALS SCIENCE↗