Collimation system baseline design for the electron storage ring at the Electron-Ion Collider
Explore the source record for details and available documents.
73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
Engineering topics
Montag, Christoph
Publications and source records attributed to Montag, Christoph.
An Induction-Type Septum Magnet for the Hadron and Electron Injection of the EIC Complex
The design of the electron Ion Collider (EIC) project is under way to be built at the Brookhaven National Laboratory (BNL) with the collaboration of the Thomas Jefferson National Accelerator Facility (TJNAF). The Rapid Cycling Synchrotron (RCS) which is part of the EIC accelerator complex will accelerate the electron beam up to 18 GeV, and the beam will be injected into the Electron Storage Ring (ESR) to collide with the hadron beam circulating in the Hadron Storage Ring (HSR) which is a modified version of the Relativistic Heavy Ion Collider (RHIC). All three synchrotrons will be located in the same tunnel. This technical note provides information on the latest electromagnetic design of the induction-type septum magnet which will be employed by EIC to Inject the beam into the HSR and RCS and also extract the beam from the RCS.
43 PARTICLE ACCELERATORS↗
The EIC accelerator: design highlights and project status
The design of the electron-ion collider (EIC) at Brookhaven National Laboratory is well underway, aiming at a peak electron-proton luminosity of 10e+34 cm^-1·sec^-1. This high luminosity, the wide center-of-mass energy range from 29 to 141 GeV (e-p) and the high level of polarization require innovative solutions to maximize the performance of the machine, which makes the EIC one of the most challenging accelerator projects to date. The complexity of the EIC will be discussed, and the project status and plans will be presented.
43 PARTICLE ACCELERATORS↗
Progress on the design of the interaction region of the Electron-Ion Collider EIC
We present an update on the design of the Interaction Region (IR) for the the Electron Ion Collider (EIC) being built at Brookhaven National Laboratory (BNL). The EIC will collide high energy and highly polarized hadron and electron beams with a center of mass energy up to 140 GeV with luminosities of up to 10^34 /cm^2/s. The IR, located at RHIC's IR6, is designed to meet the requirements of the nuclear physics community as outlined in [1]. A second IR is technically feasible but not part of the project.The magnet apertures are sufficiently large to allow desired collision products to reach the far-forward detectors; the electron magnet apertures in the rear direction are chosen to be large enough to pass the synchrotron radiation fan. In the forward direction the electron apertures are large enough for non-Gaussian tails.The paper discusses a number of recent recent changes to the design. The machine free region was recently increased from 9 to 9.5 m to allow for more space in the forward direction for the detector. The superconducting magnets on the forward side now operate at 1.9 K, which helps crosstalk and space issues.
43 PARTICLE ACCELERATORS↗
Progress on the normal conducting magnets for the Electron-Ion Collider
The electron-ion collider (EIC) at Brookhaven National Laboratory (BNL) is designed to deliver a peak luminosity of 1e+34 1/cm2 1/sec. The EIC will take advantage of the existing Relativistic Heavy Ion Collider (RHIC) facility. Two additional rings will be installed: an electron storage ring (ESR) and a rapid cycling electron synchrotron ring (RCS).This paper presents an update on the normal conducting magnet designs required for both the ESR and RCS rings. The ESR will store polarized electron beams up to 18 GeV and utilizes a triplet of dipole magnets to increase the emittance at 5 GeV and generate excess bending to create additional radiation damping to allow a larger beam-beam tune shift. The RCS will accelerate single bunches of spin-polarized electrons at various energies from 5 GeV to 18 GeV, with a ramp rate of 100 ms and 1 Hz repetition rate. Both rings require dipole, quadrupole and sextupole magnets with different specifications.
43 PARTICLE ACCELERATORS↗
Optimizing the Design Tunes of the Electron Storage Ring of the Electron-Ion Collider
The Electron-Ion Collider (EIC) presently under construction at Brookhaven National Laboratory will collide polarized high energy electron beams with hadron beams with luminosities up to 10^34cm^{-2}s^{-1} in the center mass energy range of 20-140 GeV. Preliminary beam-beam simulations resulted in an optimum working point of (.08, .06) in the Electron Storage Ring (ESR). However, during the ESR polarization simulation study this working point was found to be less than optimal for electron polarization. In this article, we present beam-beam simulation results in a wide range tune scan to search for optimal ESR design tunes that are acceptable for both beam-beam and polarization performances.
43 PARTICLE ACCELERATORS↗
Design Status of the Electron-Ion Collider
The Electron-Ion Collider is gearing up for "Critical Decision 2", theproject baseline with defined scope, cost and schedule.Lattice designs are beingfinalized, and preliminary component design is being carried out. Beam dynamicsstudies such as dynamic aperture optimization, instability and polarizationstudies, and beam-beam simulations are continuing in parallel. We report onthe latest developments and the overall status of the project, and presentthe plans for future activities.
43 PARTICLE ACCELERATORS↗
ESR Dipole Power Supply Current Ripple and Noise Specifications
This note presents key findings for the ESR main magnet dipole power supplies (PS), where we find the current ripple specification to be close to or beyond the state-of-the-art. These specifications originate from beam-beam considerations, with the requirement to limit the ripple-induced hadron emittance growth to below 10%/hour. Beam dynamics that drive this PS ripple specification arise from the beam motions at the Interaction Point (IP). The frequency of the motions can be separated into "low", compared to the betatron frequency, and "high", i.e. around the betatron frequency and harmonics. In terms of the driving frequency, "low" implies ƒ<<ƒ 0 v x,y and "fast" means ƒ≈{ƒ 0 v x,y , ƒ 0 (1- v x,y , etc.}, where ƒ 0 =1/ T 0 =78.2 kHz is the revolution frequency, and v x,y are the fractional parts of the betatron tunes. Frequencies higher than ƒ 0 /2 will be folded back due to the particles sampling the field once per turn. To provide flexibility for future lattice adjustments and working point variations, we do not consider the tunes as fixed. Instead, we assume a certain margin and allow them to potentially fall within the range of 0.1< v x,y <0.5. In other words, the high-frequency region spans approximately from 8kHz to 40 kHz. Consequently,, we definte the dipole PS ripple in two distinct frequency ranges: the low-frequency range of [1-8000] Hz and the high-frequency range of [8-40] kHz. For the physics effects we analyzed in this note, there is no distinction between the ripple (which can be approximately reproduced in the frequency domain) and the random noise if both have some power within the frequency bandwidth of interest. Therefore, while we will use the term "ripple" for short, it should always be understood that we are referring to "ripple plus noise." Except for the lower end of the low-frequency range, the impact of the rippling PS current on the beam will be considerably reduced due to the eddy currents induced in the walls of the vacuum chamber. We will account for this effect in the PS ripple specifications to follow. The remaining sections of this note are structure as follows: Section II outlines the beam-beam physics requirements for the positional stability of the beam at the IP. Section III describes the anticipated shielding effect of the eddy currents induced in the vacuum chamber. Section IV derives the ripple requirement for the low-frequency range by propagating the closed orbit ripple resulting from the rippling dipoles to the IP (relevant lattice simulation results are summarized in the Appendix). In Section V, we present the analytical criterion for the ripple in the high-frequency range by considering resonant oscillations of the electron beam around a stable closed orbit near the betatron frequency. Finally, Section VI provides a summary of our findings and discusses related work.
43 PARTICLE ACCELERATORS↗
Electron-Ion Collider Design Status
The Electron-Ion Collider (EIC) is being designed for construction at Brookhaven National Laboratory. Activities have been focused on beam-beam simulations, polarization studies, and beam dynamics, as well as on maturing the layout and lattice design of the constituent accelerators and the interaction region. The latest design advances will be presented.
43 PARTICLE ACCELERATORS↗
Optimization of chromatic optics in the electron storage ring of the Electron-Ion Collider
Not Available
43 PARTICLE ACCELERATORS↗
Design Status Update of the Electron-Ion Collider
The design of the electron-ion collider EIC to be constructed at Brookhaven National Laboratory has been continuously evolving towards a realistic and robust design that meets all the requirements set forth by the nuclear physics community in the White Paper. Over the past year activities have been focused on maturing the design, and on developing alternatives to mitigate risk. These include improvements of the interaction region design as well as modifications of the hadron ring vacuum system to accommodate the high average and peak beam currents. Beam dynamics studies have been performed to determine and optimize the dynamic aperture in the two collider rings and the beam-beam performance. We will present the EIC design with a focus on recent developments.
43 PARTICLE ACCELERATORS↗
Transverse Beam Tails and Beam Lifetime in the EIC Electron Storage Ring
For most storage ring design purposes it is sufficient to assume a Gaussian distribution of the electrons in a bunch. However, a more detailed knowledge of the population in the transverse tails beyond a few sigma is necessary to predict the beam lifetime and the synchrotron radiation load in the interaction region due to beam-gas scattering and the beam-beam interaction. This report presents simulations to determine the required vacuum level as well as to serve as input data for detailed synchrotron radiation simulations.
43 PARTICLE ACCELERATORS↗
eRHIC Design Update
The future electron-ion collider (EIC) aims at an electron-proton luminosity of 10³³ to 10³⁴ cm⁻² sec⁻¹ and a center-of-mass energy range from 20 to 140 GeV. The eRHIC design has been continuously evolving over a couple of years and has reached a considerable level of maturity. The concept is generally conservative with very few risk items which are mitigated in various ways.
43 PARTICLE ACCELERATORS↗
The eRHIC spin rotator and the beam optics of the 400 MeV transfer line to RCS
The 400 MeV LINAC 1 of the proposed eRHIC collider 1 is the first acceleration stage of the 18 GeV electron accelerator. The second acceleration stage of the electron accelerator is the Rapid Cycling Synchrotron (RCS), which can increase the energy of the electron bunches to 18 GeV and subsequently extract transfer and inject the 18 GeV electron bunches into the 18 GeV electron Storage Ring (SR) to collide with the hadron bunches of the existing (Relativistic Heavy Ion Collider (RHIC)) accelerator. This paper describes the beam optics of the transfer line between the 400 MeV LINAC and the RCS accelerator (LtRCS). The function of the LtRCS line is twofold, first to transfer the electron beam from the exit of the 400 MeV LINAC to the injection point of the RCS 1 and second to rotate the stable spin direction of the polarized electrons from the longitudinal direction to the vertical. A detailed description of the constraints to be satisfied by the LtRCS transfer line will be given. Finally, a section will also be devoted to discuss the spin rotator 2 .
43 PARTICLE ACCELERATORS↗
eRHIC design update
Explore the source record for details and available documents.
43 PARTICLE ACCELERATORS↗
eRHIC Electron Ring Design Status
For the proposed electron-ion collider eRHIC, an electron storage ring will be installed in the existing RHIC tunnel. To reach the high luminosity of up to 10³⁴ cm⁻² sec⁻¹, beam currents up to 2.5A have to be stored. Besides high luminosity the physics program requires spin polarization levels of 70 percent, with both spin "up" and spin "down" orientations present in the fill. This is only feasible by using a full-energy spin polarized injector that replaces bunches faster than the depolarization rate. To limit the repetition rate of that injector to about one hertz, the polarization lifetime in the storage ring has to be maximized by proper spin matching and countermeasures for the machine misalignments. We will give an overview of the electron storage ring design.
43 PARTICLE ACCELERATORS↗
eRHIC Design Overview
The Electron-Ion Collider (EIC) is being envisioned as the next facility to be constructed by the DOE Nuclear Physics program. Brookhaven National Laboratory is proposing eRHIC, a facility based on the existing RHIC complex as a cost effective realization of the EIC project with a peak luminosity of 10³⁴ cm⁻² sec⁻¹. An electron storage ring with an energy range from 5 to 18 GeV will be added in the existing RHIC tunnel. A spin-transparent rapid-cycling synchrotron (RCS) will serve as a full-energy polarized electron injector. Recent design improvements include reduction of the IR magnet strengths to avoid the necessity for Nb₃Sn magnets, and a novel hadron injection scheme to maximize the integrated luminosity. We will provide an overview of this proposed project and present the current design status.
43 PARTICLE ACCELERATORS↗
eRHIC design overview
Explore the source record for details and available documents.
43 PARTICLE ACCELERATORS↗