Engineering topics

Montgomery, Edward E., IV

Publications and source records attributed to Montgomery, Edward E., IV.

15 records

NASA NTRS2016

Feasibility Study for a Near Term Demonstration of Laser-Sail Propulsion from the Ground to Low Earth Orbit

This paper adds to the body of research related to the concept of propellant-less in-space propulsion utilizing an external high energy laser (HEL) to provide momentum to an ultra-lightweight (gossamer) spacecraft. It has been suggested that the capabilities of Space Situational Awareness assets and the advanced analytical tools available for fine resolution orbit determination make it possible to investigate the practicalities of a ground to Low Earth Orbit (LEO) demonstration at delivered power levels that only illuminate a spacecraft without causing damage to it. The degree to which this can be expected to produce a measurable change in the orbit of a low ballistic coefficient spacecraft is investigated. Key system characteristics and estimated performance are derived for a near term mission opportunity involving the LightSail 2 spacecraft and laser power levels modest in comparison to those proposed previously by Forward, Landis, or Marx. [1,2,3] A more detailed investigation of accessing LightSail 2 from Santa Rosa Island on Eglin Air Force Base on the United States coast of the Gulf of Mexico is provided to show expected results in a specific case.

Montgomery, Edward E., IV↗

NASA NTRS2008

NanoSail-D

The "NanoSail-D" mission is currently scheduled for launch onboard a Falcon-1 Launch Vehicle in the early June 2008 timeframe. The NanoSail-D spacecraft will consist of a solar sail subsystem stowed in a 2U volume and a 1U spacecraft bus, provided by Ames Research Center. The primary objectives of the NanoSail-D technology demonstration mission are to fabricate, stow and deploy on-orbit a solar sail and perform a de-orbit maneuver to demonstrate a potential orbital debris mitigation technology. The NanoSail-D mission is being developed through a collaborative effort between the NASA Marshall Space Flight Center and the NASA Ames Research Center Small Spacecraft Office. Details of the NanoSail-D system will be presented, including: 1) design details of the solar sail reflective membrane quadrants, gossamer booms, deployment system and passive attitude control system, 2) design analysis results including structural, thermal, environmental, orbital debris and safety, and 3) test results including deployment, ascent venting, launch vibration and PPOD integration verification.

Montgomery, Edward E., IV↗

NASA NTRS2006

Status of Solar Sail Propulsion: Moving Toward an Interstellar Probe

NASA's In-Space Propulsion Technology Program has developed the first-generation of solar sail propulsion systems sufficient to accomplish inner solar system science and exploration missions. These first-generation solar sails, when operational, will range in size from 40 meters to well over 100 meters in diameter and have an areal density of less than 13 grams-per-square meter. A rigorous, multiyear technology development effort culminated last year in the testing of two different 20-meter solar sail systems under thermal vacuum conditions. This effort provided a number of significant insights into the optimal design and expected performance of solar sails as well as an understanding of the methods and costs of building and using them. In a separate effort, solar sail orbital analysis tools for mission design were developed and tested. Laboratory simulations of the effects of long-term space radiation exposure were also conducted on two candidate solar sail materials. Detailed radiation and charging environments were defined for mission trajectories outside the protection of the earth's magnetosphere, in the solar wind environment. These were used in other analytical tools to prove the adequacy of sail design features for accommodating the harsh space environment. Preceding, and in conjunction with these technology efforts, NASA sponsored several mission application studies for solar sails, including one that would use an evolved sail capability to support humanity's first mission into nearby interstellar space. The proposed mission is called the Interstellar Probe. The Interstellar Probe might be accomplished in several ways. A 200-meter sail, with an areal density approaching 1 gram-per-square meter, could accelerate a robotic probe to the very edge of the solar system in just under 20 years from launch. A sail using the technology just demonstrated could make the same mission, but take significantly longer. Conventional chemical propulsion systems would require even longer flight times. Spinner sails of the type being explored by the Japanese may also be a good option, but the level of maturity in that technology is not clear. While the technology to support a 200-meter, ultralightweight sail mission is not yet in hand, the recent NASA investments in solar sail technology are an essential first step toward making it a reality. This paper will describe the status of solar sail propulsion within NASA, near-term solar sail mission applications, and the plan to advance the technology to the point where the Interstellar Probe mission can be flown.

Johnson, Les↗

NASA NTRS2006

Recent Advances in Solar Sail Propulsion at NASA

Supporting NASA's Science Mission Directorate, the In-Space Propulsion Technology Program is developing solar sail propulsion for use in robotic science and exploration of the solar system. Solar sail propulsion will provide longer on-station operation, increased scientific payload mass fraction, and access to previously inaccessible orbits for multiple potential science missions. Two different 20-meter solar sail systems were produced and successfully completed functional vacuum testing last year in NASA Glenn's Space Power Facility at Plum Brook Station, Ohio. The sails were designed and developed by ATK Space Systems and L'Garde, respectively. These sail systems consist of a central structure with four deployable booms that support the sails. This sail designs are robust enough for deployments in a one atmosphere, one gravity environment, and are scalable to much larger solar sails-perhaps as much as 150 meters on a side. In addition, computation modeling and analytical simulations have been performed to assess the scalability of the technology to the large sizes (>150 meters) required for first generation solar sails missions. Life and space environmental effects testing of sail and component materials are also nearly complete. This paper will summarize recent technology advancements in solar sails and their successful ambient and vacuum testing.

Johnson, Les↗

NASA NTRS2004

In-Space Propulsion (ISP) Solar Sail Propulsion Technology Development

An overview of the rationale and content for Solar Sail Propulsion (SSP), the on-going project to advance solar technology from technology readiness level 3 to 6 will be provided. A descriptive summary of the major and minor component efforts underway will include identification of the technology providers and a listing of anticipated products Recent important results from major system ground demonstrators will be provided. Finally, a current status of all activities will provided along with the most recent roadmap for the SSP technology development program.

Montgomery, Edward E., IV↗

NASA NTRS2004

Development of Solar Sail Propulsion for Inner Solar System NASA Science Missions

This paper examines recent assessments of the technology challenges facing solar sails, identifies the systems and technologies needing development, and the approach employed by NASA's In-Space Propulsion program in NASA to achieve near-term products that move this important technology from low technology readiness level toward the goal of application to science missions in near-Earth space and beyond.

Montgomery, Edward E., IV↗

NASA NTRS2004

NASA's Integrated Development of Solar Sail Propulsion Project

Solar sails have been studied for a variety of missions and have the potential to provide cost effective, propellantless propulsion that enables longer on-station operation, increased scientific payload mass fraction, and access to previously inaccessible orbits (e. g., non-Keplerian, high solar latitudes, etc.). Research being conducted by the In-Space Propulsion (ISP) Technologies Projects is at the forefront of NASA's efforts to mature propulsion technologies that will enable or enhance a variety of space science missions. Solar sail propulsion systems will be required to meet the challenge of monitoring and predicting space weather by the Office of Space Science's (OSS) Living with a Star (LWS) program. Near-to-mid-term mission needs include monitoring of solar activity and observations at high solar latitudes. Work currently funded by the ISP s Solar Sail Propulsion (SSP) project is based on the quantitative demonstration of scalability of present solar sail subsystem designs and concepts to future mission requirements through ground testing of hardware, computational modeling and analytical simulations. This paper will give an overview of the Solar Sail Propulsion project's major development tasks of fabricating and testing two different subscale (400 square meter sail) solar sail system architectures. It will then be shown how either of these subscale prototypes can evolve into a flight validation system and briefly discuss the mission parameter. The paper will conclude with a discussion on how a flight validation will exercise the quantitative tools needed to demonstrate the scale to the size needed for the Solar Polar Imager and L1-Diamond SEC roadmap missions.

Garbe, Gregory↗

NASA NTRS2003

An Overview Of NASA's Solar Sail Propulsion Project

Research conducted by the In-Space Propulsion (ISP) Technologies Projects is at the forefront of NASA's efforts to mature propulsion technologies that will enable or enhance a variety of space science missions. The ISP Program is developing technologies from a Technology Readiness Level (TRL) of 3 through TRL 6. Activities under the different technology areas are selected through the NASA Research Announcement (NRA) process. The ISP Program goal is to mature a suite of reliable advanced propulsion technologies that will promote more cost efficient missions through the reduction of interplanetary mission trip time, increased scientific payload mass fraction, and allowing for longer on-station operations. These propulsion technologies will also enable missions with previously inaccessible orbits (e.g., non-Keplerian, high solar latitudes). The ISP Program technology suite has been prioritized by an agency wide study. Solar Sail propulsion is one of ISP's three high-priority technology areas. Solar sail propulsion systems will be required to meet the challenge of monitoring and predicting space weather by the Office of Space Science s (OSS) Living with a Star (LWS) program. Near-to-mid-term mission needs include monitoring of solar activity and observations at high solar latitudes. Near-term work funded by the ISP solar sail propulsion project is centered around the quantitative demonstration of scalability of present solar sail subsystem designs and concepts to future mission requirements through ground testing, computer modeling and analytical simulations. This talk will review the solar sail technology roadmap, current funded technology development work, future funding opportunities, and mission applications.

Garbe, Gregory↗

NASA NTRS2003

Places Only Sails Can Go

Solar sails are a near term, low thrust, propellantless propulsion technology suitable for orbital maneuvering, station keeping, and attitude control applications for small payloads. Furthermore, these functions can be highly integrated, reducing mass, cost and complexity. The solar sail concept is based on momentum exchange with solar flux reflected from a large, deployed thin membrane. Thrust performance increases as the square of the distance to the sun. In comparison to conventional chemical systems, there are missions where solar sails are vastly more and less economical. The less attractive applications involve large payloads, outer solar system transfers, and short trip times. However, for inclination changes and station keeping at locations requiring constant thrust, the solar sail is the only economical option for missions of more than a few weeks duration. We compare the location and energies required for these applications between solar sails, advanced electric propulsion, and conventional rockets. We address the effect on mass fraction to understand solar sail mission cost and capability. Finally, the benefit of potential applications to near term science missions is reported.

Montgomery, Edward E., IV↗

NASA NTRS2002

Rapid Maturation of Edge Sensor Technology and Potential Application in Large Space Telescopes with Segmented Primary Mirrors

This paper explores the history and results of the last two year's efforts to transition inductive edge sensor technology from Technology Readiness Level 2 to Technology Readiness Level 6. Both technical and programmatic challenges were overcome in the design, fabrication, test, and installation of over a thousand sensors making up the Segment Alignment Maintenance System (SAMs) for the 91 segment, 9.2-meter. Hobby Eberly Telescope (HET). The integration of these sensors with the control system will be discussed along with serendipitous leverage they provided for both initialization alignment and operational maintenance. The experience gained important insights into the fundamental motion mechanics of large segmented mirrors, the relative importance of the variance sources of misalignment errors, the efficient conduct of a program to mature the technology to the higher levels. Unanticipated factors required the team to develop new implementation strategies for the edge sensor information which enabled major segmented mirror controller design simplifications. The resulting increase in the science efficiency of HET will be shown. Finally, the on-going effort to complete the maturation of inductive edge sensor by delivering space qualified versions for future IR (infrared radiation) space telescopes.

Montgomery, Edward E., IV↗

NASA NTRS2002

Ultralightweight Space Deployable Primary Reflector Demonstrator

A concept has been developed and analyzed and several generational prototypes built for a gossamer-class deployable truss for a mirror or reflector with many smaller precisely-figured solid elements attached will, for at least the next several decades, minimize the mass of a large primary mirror assembly while still providing the high image quality essential for planet-finding and cosmological astronomical missions. Primary mirror segments are mounted in turn on ultralightweight thermally-formed plastic panels that hold clusters of mirror segments in rigid arrays whose tip/tilt and piston would be corrected over the scale of the plastic panels by the control segments. Prototype panels developed under this program are 45 cm wide and fabricated from commercially available Kaplan sheets. A three-strut octahedral tensegrity is the basis for the overall support structure. Each fundamental is composed of two such octahedrons, rotated oppositely about a common triangular face. Adjacent modules are joined at the nodes of the upper and lower triangles to form a deployable structure that could be made arbitrarily large. A seven-module dowel-and-wire prototype has been constructed. Deployment techniques based on the use of collapsing toggled struts with diagonal tensional elements allows an assembly of tensegrities to be fully collapsed and redeployed. The prototype designs will be described and results of a test program for measuring strength and deformation will be presented.

Montgomery, Edward E., IV↗

NASA NTRS2002

The Beamed Energy Technology Working Group, Programs and Goals

A brief description of the Beamed Energy Technology Program will be given. Its relationship to the overall Advanced Technology Program at Marshall Space Flight Center will be discussed. A summary description of the known potential benefits and technical issues remaining in the development of a viable system will be presented along with program plans for a NASA Research Announcement in FY03 to begin development of relevant technologies and systems concepts. The results of workshop activity by the Beamed Energy Technology Working Group will be provided.

Montgomery, Edward E., IV↗

NASA NTRS2001

Review of MSFC SBIR's: Xinetics RB-SiC Mirror Fabrication Study, UltraMet PG Foam Mirror Fabrication Study, Blue Line Eng. AI Enhanced Edge Sensors and Fully Active Subscale Telescope

This presentation will briefly review the objectives and anticipated benefits of several Small Business Innovative Research projects in progress under the direction of Marshall Space Flight Center. They all relate to the development of advanced optical systems technologies important to future astronomical missions in space.

Montgomery, Edward E., IV↗

NASA NTRS1998

The Case for Aggressive Segmentation of the Primary Mirror of the Next Generation Space Telescope and Future ORIGINS Missions

Optical performance variations are considered from several factors including the gap between regular hexagonal mirror segments, the relative ability of segments of different size to be manufactured with low wavefront error, and expected mirror deformations. Additionally a weight variation function will be driven by recently postulated relationships which can be expressed so as to determine thickness of the mirror segment to satisfy: (1) polishing pressures (2) 1-g sage deflection, and (3) thermal induced stress as well as ancillary masses including actuators, wiring, and electronics. The result will be to survey the trade space of segment number and size for a range of apertures from 4 to 20 meters.

Montgomery, Edward E., IV↗

NASA NTRS1992

System evaluations of laser power beaming options

The major technology options for high-energy FELs and adaptive optics available to the Space Laser Energy (SELENE) program are reviewed. Initial system evaluations of these options are described. A feasibility assessment of laser power beaming is given.

Montgomery, Edward E., IV↗