Search NASA⌕ Search

Engineering topics

Montgomery, Fred C

Publications and source records attributed to Montgomery, Fred C.

First elevated-temperature performance testing of coated particle fuel compacts from the AGR-1 irradiation experiment

In the AGR-1 irradiation experiment, 72 coated-particle fuel compacts were taken to a peak burnup of 19.5% fissions per initial metal atom with no in-pile failures. This paper discusses the first post-irradiation test of these mixed uranium oxide/uranium carbide fuel compacts at elevated temperature to examine the fuel performance under a simulated depressurized conduction cooldown event. A compact was heated for 400 h at 1600 degrees C. Release of 85Kr was monitored throughout the furnace test as an indicator of coating failure, while other fission product releases from the compact were periodically measured by capturing them on exchangeable, water-cooled deposition cups. No coating failure was detected during the furnace test, and this result was verified by subsequent electrolytic deconsolidation and acid leaching of the compact, which showed that all SiC layers were still intact. However, the deposition cups recovered significant quantities of silver, europium, and strontium. Based on comparison of calculated compact inventories at the end of irradiation versus analysis of these fission products released to the deposition cups and furnace internals, the minimum estimated fractional losses from the compact during the furnace test were 1.9 x 10-2 for silver, 1.4 x 10-3 for europium, and 1.1 x 10-5 for strontium. Other post-irradiation examination of AGR-1 compacts indicates that similar fractions of europium and silver may have already been released by the intact coated particles during irradiation, and it is therefore likely that the detected fission products released from the compact in this 1600 degrees C furnace test were from residual fission products in the matrix. Gamma analysis of coated particles deconsolidated from the compact after the heating test revealed that silver content within each particle varied considerably; a result that is probably not related to the furnace test, because it has also been observed in other as-irradiated AGR-1 compacts. X-ray imaging of selected particles was performed to examine the internal microstructure. This examination revealed variable irradiation performance of the coating layers, but sufficient statistical sampling is not yet available to identify any possible correlation to variation in individual particle fission product retention.

99 GENERAL AND MISCELLANEOUS↗

Fabrication and Characterization of Fully Ceramic Microencapsulated Fuels

The current generation of fully ceramic microencapsulated fuels, consisting of Tristructural Isotropic fuel particles embedded in a silicon carbide matrix, is fabricated by hot pressing. Matrix powder feedstock is comprised of alumina - yttria additives thoroughly mixed with silicon carbide nanopowder using polyethyleneimine as a dispersing agent. Fuel compacts are fabricated by hot pressing the powder - fuel particle mixture at a temperature of 1800-1900 C using compaction pressures of 10-20 MPa. Detailed microstructural characterization of the final fuel compacts shows that oxide additives are limited in extent and are distributed uniformly at silicon carbide grain boundaries, at triple joints between silicon carbide grains, and at the fuel particle-matrix interface.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Compact, DC-electrical biased sulfur dioxide sensing elements for use at high temperatures

Fabrication and operation of sensing elements for the detection of sulfur dioxide (SO_2) at high temperature (800 900 ^oC) is reported. The sensing elements consisted of three (two oxide and one Pt) electrodes on yttria-stabilized zirconia substrates. To operate the elements, a DC current (typically about 0.1 mA) is driven between two of the electrodes and the voltage between one of these electrodes and the third electrode is used as the sensing signal. These sensing elements respond very strongly to SO_2, for example 2 ppm_V of SO_2 in a background of 7 vol% O_2, balance N_2 was found to produce a >10% change in the sensing signal, which could be easily detected. Sensing elements fabricated to be nominally identical were shown to yield qualitatively identical sensing behavior, and temperature, oxygen content, and flow were all found to strongly impact sensing performance. The impact of interferents, such as NO_x and CO, was evaluated and found to be relatively small in comparison to the SO_2 response. The sensing response, over a 1 month period, was very stable, with the ratio of the average change in sensing signal over one day to the average sensing signal magnitude being about 0.1%.

36 MATERIALS SCIENCE↗

Treatment Techniques to Prevent Cracking of Amorphous Microspheres Made by the Internal Gelation Process

The internal gelation process has been used to make plutonium gel spheres and zirconium gel spheres with stabilized yttrium. However, attempts to convert these amorphous gel spheres into kernels have failed due to cracking during the subsequent heat treatments. The porosity of the amorphous microspheres is typically not sufficient to permit the gases that are formed during subsequent heat treatments to escape. The microspheres will crack when the internal pressure becomes too great. In this study, several treatment techniques were applied to zirconium microspheres stabilized with yttrium in an effort to reduce or eliminate cracking. A combination of water washes, a pressurized water treatment at 473 K for 3 h, and a Dowanol PM treatment was shown to eliminate the cracking problem with the zirconium microspheres, which were heated to 1438 K.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Installation and Initial Operation of an On-line Target Imaging System for SNS

After several years of operation, the SNS now enters an era of megawatt class operation. At this intensity level, the target will be operating closer to its engineering limits and the beam profile on target must be carefully controlled. During commissioning and early operations, a temporary imaging system was used to measure the proton density on target. This system was not designed to survive the increasing power levels and it had to be removed in the second half of 2006. Since then, no direct measurement of beam properties at the target has been available. A collaboration was forged to remedy this situation, and has resulted in a new imaging system consisting of three major components: a thermal-sprayed luminescent coating deposited on the target nose, a radiation-tolerant optical system installed upstream of the target, and an image acquisition system integrated with the accelerator controls network. The design, installation, and integration of these components will be described. Initial beam measurements and image analysis results will be presented. Lessons learned during this initial operating experience have been documented and will guide the collaboration s future plans.

43 PARTICLE ACCELERATORS↗

A technique for monitoring SO2 in combustion exhausts: Use of a non-Nernstian sensing element in combination with an upstream catalytic filter

Detection of sulfur dioxide (SO2) at high temperature (600 750 oC) in the presence of some interferents found in typical combustion exhausts (oxides of nitrogen (NO2 and NO, "NOx"), CO2, CO, and hydrocarbon (C3H6)) is described. The detection scheme involves use of a catalytic filter in front of a non-Nernstian sensing element. The catalytic filter was a Ni:Cr powder bed operating at 850 oC and the sensing elements were pairs of platinum (Pt) and oxide (Ba-promoted copper chromite ((Ba,Cu)xCryOz) and Sr-modified lanthanum ferrite (LSF)) electrodes on yttria-stabilized zirconia. The Ni:Cr powder bed was capable of reducing the sensing element response to NOx, CO, and C3H6, but the presence of NOx (100 ppm by volume) still interfered with the SO2 response of the Pt-(Ba,Cu)xCryOz sensing element at 600 oC, causing approximately a 7 mV (20%) reduction in the response to 120 ppm SO2 and a response equivalent to about 20 ppm SO2 in the in the absence of SO2. The Pt-LSF sensing element, operated at 750 oC, did not suffer from this NOx interference but at the cost of a reduced SO2 response magnitude (120 ppm SO2 yielded ~10 mV, in contrast to ~30 mV for the Pt-(Ba,Cu)xCryOz sensing element). The powder bed and Pt-LSF sensing element were operated continuously over approximately 350 hours, and the response to SO2 drifted downward by about 7%, with most of this change occurring during the initial 100 hours of operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DETECTION OF SO2 AT HIGH TEMPERATURE WITH ELECTRICALLY BIASED, SOLID-ELECTROLYTE SENSING ELEMENTS

Design and operation of sensing elements for the detection of sulfur dioxide (SO2) at high temperature (800 900 oC) is described. The sensing elements consisted of three (two oxide and one Pt) electrodes on yttria-stabilized zirconia substrates. To operate the elements, a constant current (usually on the order of 0.1 mA) was driven between two of the electrodes and the voltage between one of these electrodes and the third electrode was monitored and used as the sensing signal. In one example, 31 ppm SO2 caused an approximately 40% change in the element output, and 2 ppm of SO2 could be easily detected. The cross-sensitivity to several interferents such as NOx was evaluated and found to be relatively small in comparison to the SO2 response.

01 COAL, LIGNITE, AND PEAT↗