Engineering topics

Montgomery, Raymond C.

Publications and source records attributed to Montgomery, Raymond C..

At least 37 records · Page 2

NASA NTRS1992

Nonlinear modeling of a long flexible manipulator and control by inertial devices

The authors consider the modeling and control of a planar, long flexible manipulator that is representative of current space-based robotic arms. The arm is equipped with three actuators: 1) a shoulder motor; 2) a torque wheel at the tip; and 3) a proof-mass actuator at the tip. The goal is to investigate the potential use of inertial devices as control inputs for maneuvering tasks and vibration suppression. The parameters used for the inertial devices at the tip are comparable to those specified for the Mini-Mast facility at the Langley Research Center. A nonlinear distributed parameter model is obtained by the extended Hamilton principle. The associated eigenvalue/eigenfunction problem is solved and a finite-dimensional state space model is assembled. A preliminary design of a linear quadratic regulator is used, and computer simulation results illustrate the benefits of using the proposed actuators.

Barbieri, Enrique↗

NASA NTRS1991

Analytic and simulation studies on the use of torque-wheel actuators for the control of flexible robotic arms

This paper presents results of analytic and simulation studies to determine the effectiveness of torque-wheel actuators in suppressing the vibrations of two-link telerobotic arms with attached payloads. The simulations use a planar generic model of a two-link arm with a torque wheel at the free end. Parameters of the arm model are selected to be representative of a large space-based robotic arm of the same class as the Space Shuttle Remote Manipulator, whereas parameters of the torque wheel are selected to be similar to those of the Mini-Mast facility at the Langley Research Center. Results show that this class of torque-wheel can produce an oscillation of 2.5 cm peak-to-peak in the end point of the arm and that the wheel produces significantly less overshoot when the arm is issued an abrupt stop command from the telerobotic input station.

Montgomery, Raymond C.↗

NASA NTRS1991

Dynamic analysis of truss-beam system

A simple truss-beam method for determining the dynamic characteristics of the space structures intended to perform various tasks in orbit is presented. Algorithms are provided to determine the flexibility matrix of the truss beam for use in the equation of motion. The natural frequencies obtained through this method are compared with those obtained through the finite element method. An experimental procedure for verifying the theoretical results is described. It is concluded that the truss-beam method is a simple analysis technique that yields reasonably accurate results with a minimum of computational effort, especially for the critical lower bending modes of flexible structures. The method takes less computer time than more conventional methods and can be programed in both BASIC and FORTRAN for use in micro- and mainframe computers.

Abu-Saba, Elias G.↗

NASA NTRS1991

The spacecraft control laboratory experiment optical attitude measurement system

A stereo camera tracking system was developed to provide a near real-time measure of the position and attitude of the Spacecraft COntrol Laboratory Experiment (SCOLE). The SCOLE is a mockup of the shuttle-like vehicle with an attached flexible mast and (simulated) antenna, and was designed to provide a laboratory environment for the verification and testing of control laws for large flexible spacecraft. Actuators and sensors located on the shuttle and antenna sense the states of the spacecraft and allow the position and attitude to be controlled. The stereo camera tracking system which was developed consists of two position sensitive detector cameras which sense the locations of small infrared LEDs attached to the surface of the shuttle. Information on shuttle position and attitude is provided in six degrees-of-freedom. The design of this optical system, calibration, and tracking algorithm are described. The performance of the system is evaluated for yaw only.

Welch, Sharon S.↗

NASA NTRS1991

Simulator evaluation of system identification with on-line control law update for the controls and astrophysics experiment in space

A procedure for optimizing the performance of large flexible spacecraft that require active vibration suppression to achieve required performance is presented. The procedure is to conduct on-orbit testing and system identification followed by a control system design. It is applied via simulation to a spacecraft configuration currently being considered for flight test by NASA - the Controls, Astrophysics, and Structures Experiment in Space (CASES). The system simulator is based on a NASTRAN finite element structural model. A finite number of modes is used to represent the structural dynamics. The system simulator also includes models of the electronics, actuators, sensors, the digital controller, and the internal and external disturbances. Nonlinearities caused by quantization are included in the study to examine tolerance of the procedure to modelling errors. Disturbance and sensor noise is modelled as a Gaussian process. For system identification, the system is excited using sinusoidal inputs at the resonant frequencies of the structure using each actuator. Mode shapes, frequencies, and damping ratios are identified from the unforced response sensor data after each excitation. Then, the excitation data is used to identify the actuator influence coefficients. The results of the individual parameter identification analyses are assembled into an aggregate system model. The control design is accomplished based only on the identified model using multi-input/output linear quadratic Gaussian theory. Its performance is evaluated based on time-to-damp as compared with the uncontrolled structure.

Montgomery, Raymond C.↗

NASA NTRS1991

Control with distributed sensing and processing

A design procedure for control systems that use distributed sensing and processing is summarized. The procedure is applied to the problem of damping vibrations of a simply supported beam.

Montgomery, Raymond C.↗

NASA NTRS1991

Studies on distributed sensing and processing for the control of large flexible spacecraft

Technology is being developed to process signals from distributed sensors using distributed computations. These distributed sensors provide a new feedback capability for vibration control that has not been exploited. Additionally, the sensors proposed are of an optical and distributed nature and could be employed with known techniques of distributed optical computation (Fourier optics, etc.) to accomplish the control system functions of filtering and regulation in a distributed computer. This paper reviews a procedure for the analytic design of control systems for this application. For illustration, the procedure is applied to the problem of suppressing the vibrations of a simply supported beam. A simulator has been developed to study the effects of sensor and processing errors. An extensive study of the effects of these errors on estimation and regulation performance is presented.

Montgomery, Raymond C.↗

NASA NTRS1990

Real-time dynamic holographic image storage device

A real-time dynamic holographic image storage device uses four-wave mixing in a pair of photorefractive crystals. An oscillation is produced between the crystals which can be maintained indefinitely after the initial object beam is discontinued. The object beam produces an interference pattern in a first crystal to produce phase-conjugated object beam which is directed towards the second crystal. In the second crystal another interference pattern is created which produces a reconstructed object beam. The reconstructed object beam is directed back towards the first crystal. The interference patterns are produced by interaction of the object and phase-conjugated object beam with a read and write beam in each of the crystals. By manipulation of the ratio of the read and write beam intensities in at least one of the crystals, the phase-conjugate or reconstructed object beam output therefrom can be amplified to maintain stable oscillation between the two crystals.

Lafleur, Sharon S.↗

NASA NTRS1990

The truss-beam and space technology

A method is presented herein to determine the dynamic characteristics of truss-beam systems for both planar and space structures. Results from this approach are compared with those of the finite element method and test results. The truss-beam model is based on the assumptions of negligible web contribution, i.e., very large flexible structures. Future experimental evaluation of the plane truss-system is planned at North Carolina Agricultural and Technical State University and this experimental program is described.

Abu-Saba, Elias G.↗

NASA NTRS1990

Active control test on the Mini-Mast

A Linear Quadratic Gaussian (LQG) design process is presented and applied to a large flexible ground test facility, the Mini-Mast, for validation. For the design, nine displacement sensors were used. Three torque wheel actuators were used for damping augmentation. Results were dramatic, indicating an improvement in damping from 3 percent to 30 percent of critical. The tests proved the effectiveness of the procedure in designing effective vibration damping systems.

Montgomery, Raymond C.↗

NASA NTRS1990

Simplified truss-beam modeling - Dynamic analysis

A model of the truss-beam has been developed and a set of algorithms provided to determine the flexibility matrix. Using lumped masses at the panel juncture, and applying the flexibility matrix in the equation of motion for the system, the dynamic characteristics are readily determined. An interactive computer program has been developed both in Basic and in Fortran for the IMB PC and other compatible micro-computers. This method is used to determine the lower natural frequencies of two truss-beams, and the results compared with those found by others.

Abu-Saba, Elias G.↗

NASA NTRS1990

On the use of distributed sensing in control of large flexible spacecraft

Distributed processing technology is being developed to process signals from distributed sensors using distributed computations. Thiw work presents a scheme for calculating the operators required to emulate a conventional Kalman filter and regulator using such a computer. The scheme makes use of conventional Kalman theory as applied to the control of large flexible structures. The required computation of the distributed operators given the conventional Kalman filter and regulator is explained. A straightforward application of this scheme may lead to nonsmooth operators whose convergence is not apparent. This is illustrated by application to the Mini-Mast, a large flexible truss at the Langley Research Center used for research in structural dynamics and control. Techniques for developing smooth operators are presented. These involve spatial filtering as well as adjusting the design constants in the Kalman theory. Results are presented that illustrate the degree of smoothness achieved.

Montgomery, Raymond C.↗

NASA NTRS1989

Mini-mast dynamic analysis using the truss-beam model

The Mini-Mast is a generic space truss designed by Astro Aerospace Corp. A 210 meter truss located in the Structural Dynamics research Lab of NASA Langley is used in comprehensive active vibration control experiments on a realistic large space structure. Some predictions of the natural frequencies and mode shapes were made based on the Finite Element model. The purpose here is to use the Truss-Beam model developed by Elias G. Abu-Saba to predict the natural frequencies of the Mini-Mast and then compare the results with those obtained from the FE model. Imperfections of the joints are modeled, and joint contribution to the flexibility matrix of the structure is noted. The natural frequencies are obtained. An iterative procedure is used to enhance the Truss-Beam model by comparing these results with experimental ones.

Abu-Saba, Elias G.↗

NASA NTRS1989

Optical processing for distributed sensors in control of flexible spacecraft

A recent potential of distributed image processing is discussed. Applications in the control of flexible spacecraft are emphasized. Devices are currently being developed at NASA and in universities and industries that allow the real-time processing of holographic images. Within 5 years, it is expected that, in real-time, one may add or subtract holographic images at optical accuracy. Images are stored and processed in crystal mediums. The accuracy of their storage and processing is dictated by the grating level of laser holograms. It is far greater than that achievable using current analog-to-digital, pixel oriented, image digitizing and computing techniques. Processors using image processing algebra can conceptually be designed to mechanize Fourier transforms, least square lattice filters, and other complex control system operations. Thus, actuator command inputs derived from complex control laws involving distributed holographic images can be generated by such an image processor. Plans are revealed for the development of a Conjugate Optics Processor for control of a flexible object.

Montgomery, Raymond C.↗

NASA NTRS1988

Analytic redundancy management for SCOLE

The objective of this work is to develop a practical sensor analytic redundancy management scheme for flexible spacecraft and to demonstrate it using the SCOLE experimental apparatus. The particular scheme to be used is taken from previous work on the Grid apparatus by Williams and Montgomery.

Montgomery, Raymond C.↗

NASA NTRS1988

Analytic redundancy management for systems with appreciable structural dynamics

This paper deals with analytic redundancy management of systems that have appreciable structural dynamics and require active control. The class of systems considered is large, lightweight spacecraft that have large numbers of distributed sensors and actuators. Both preliminary design and on-line operations are studied. For the preliminary design we deal with the placement of the sensor and actuator components on a highly flexible spacecraft. For on-line operation an analytic redundancy management system based on examination of the residuals of a Kalman filter is considered. A large, flexible grid made of overlapping aluminum bars is used to experimentally evaluate this analytic redundancy management system. Results of the experimental evaluation are included in the paper.

Montgomery, Raymond C.↗

NASA NTRS1988

Dynamic analysis of the joint dominated beam

A method for determining the vibrational modes of the joint dominated beam is presented with reference to space erectable structures. Mathematical models with and without joint imperfection are developed. Joint imperfection is represented by a simple flexibility, k, in the axial direction of the chord members only. An interactive computer program is used to obtain eigenvalue characteristics and mode shapes of the system. Results are presented on frequencies of the given truss beam with and without joint imperfections for three-panel and 10-panel models. Also presented are results of parametric studies of the beam truss models of three and 10 panels with k = 0.05, 0.10, 0.50, and 1.0 x 10 to the -7th.

Abu-Saba, Elias G.↗

NASA NTRS1987

Recent developments in the experimental identification of the dynamics of a highly flexible grid

Control effectiveness tests of reaction wheel actuators attached to a highly flexible grid are reported. Analytic determination of actuator control effectiveness is accomplished with finite-element modeling. Experimental determination is done with a least-square parameter identification algorithm that identifies the control coefficients of the second-order difference equation model of each vibration mode. The algorithm assumes a model with frequency and damping predetermined from free-decay tests for each mode. Accounting for the difference in forced and resonant frequency was necessary to produce control effectiveness estimates that are in reasonable agreement with the analytic predictions. The average error for control effectiveness coefficients greater than 5/sq sec was 6.384 percent.

Montgomery, Raymond C.↗