Engineering topics

Moody, John D.

Publications and source records attributed to Moody, John D..

6 records

DOE OSTI2024

Deposition of ultrathick heavy-metal alloys on rotating substrates by high-power impulse magnetron sputtering: Target erosion effects

Sputter deposition of ultrathick (≈20μm) Au–Ta alloy coatings on sphero-cylindrical substrates is key for the fabrication of hohlraums for magnetically assisted inertial confinement fusion. In this work, we study the deposition of AuTa 4 alloy coatings onto rotating substrates. We use high-power impulse magnetron sputtering (HiPIMS) in a constant peak target voltage mode. Results show that the target erosion state has a strong impact on the dominant crystallographic phase, microstructure, surface morphology, and electrical resistivity of AuTa 4 films. This is due to effects of changes in the confining magnetic field with target erosion on the HiPIMS discharge characteristics and the sputter source output. We quantify these effects via plasma diagnostics and discuss the optimization of HiPIMS deposition of ultrathick films for cases when target erosion effects dominate film properties.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Performance scaling with an applied magnetic field in indirect-drive inertial confinement fusion implosions

Magnetizing a cryogenic deuterium–tritium (DT)-layered inertial confinement fusion (ICF) implosion can improve performance by reducing thermal conduction and improving DT-alpha confinement in the hot spot. A room-temperature, magnetized indirect-drive ICF platform at the National Ignition Facility has been developed, using a high-Z, high-resistivity AuTa 4 alloy as the hohlraum wall material. Experiments show a 2.5× increase in deuterium–deuterium (DD) neutron yield and a 0.8-keV increase in hot-spot temperature with the application of a 12-T B-field. Further, for an initial 26-T B-field, we observed a 2.9× yield increase and a 1.1-keV temperature increase, with the inferred burn-averaged B-field in the compressed hot spot estimated to be 7.1 ± 1.8 kT using measured primary DD-n and secondary DT-n neutron yields.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Specular reflections (“glint”) of the inner beams in a gas-filled cylindrical hohlraum

Herein we report on the experimental measurement of specular reflection (“glint”) of laser beams off the hohlraum wall in inertial confinement fusion experiments at the National Ignition Facility. In a hohlraum, glinted light can escape the opposite laser entrance hole of the hohlraum and is a potential laser energy loss mechanism. The total measured glint on the inner cones of beams is measured to be less than 8 TW (when using the full National Ignition Facility laser), which is <2% of incident peak power. The simulated x-ray flux exceeds the measurement by 10%–20%, and glinted laser light is unable to account for this discrepancy. Similar inner beam glint was measured for ρ = 0.3 and 0.6 mg/cc gas fill hohlraums, but no glint was detected for 1.2 mg/cc densities. Inner beam glint is dominated by the lowest angle 21.5 beams within a 23.5 quad, and it is at most 30% sensitive to different quad polarization arrangements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Tantalum Suboxide Films with Tunable Composition and Electrical Resistivity Deposited by Reactive Magnetron Sputtering

Tantalum-based films with tailored composition, density, and electrical resistivity are of interest for next generation hohlraums for magnetized indirect-drive inertial confinement fusion. Here, we use reactive direct-current magnetron sputtering to deposit tantalum suboxide films with O content in the range of 46–71 at.%. In contrast to a common approach involving varying reactive gas contents, compositional control is achieved kinetically by changing the total chamber pressure and the deposition rate, while keeping the working gas mix of Ar-5%O2 constant. The resultant films are X-ray amorphous with electrical resistivity varying by over seven orders of magnitude. The dominant conduction mechanism changes from metallic to activated tunneling above ∼55 at.% of O, which is characterized by a sharp increase in resistivity and a decrease in the carrier density at low temperatures.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Magnetized ICF implosions: Scaling of temperature and yield enhancement

This work investigates the impact of an applied magnetic field on the yield and hot-spot temperature of inertial confinement fusion implosions. A scaling of temperature amplification due to magnetization is shown to be in agreement with unperturbed two-dimensional (2D) extended-magnetohydrodynamic simulations. A perfectly spherical hot-spot with an axial magnetic field is predicted to have a maximum temperature amplification of 37%. However, elongation of the hot-spot along field lines raises this value by decreasing the hot-spot surface area along magnetic field lines. A scaling for yield amplification predicts that a magnetic field has the greatest benefit for low-temperature implosions; this is in agreement with simplified 1D simulations, but not 2D simulations where the hot-spot pressure can be significantly reduced by heat-flow anisotropy. Simulations including a P2 drive asymmetry then show that the magnetized yield is a maximum when the capsule drive corrects the hot-spot shape to be round at neutron bang time. An applied magnetic field is also found to be most beneficial for implosions that are more highly perturbed, exceeding the theoretical yield enhancement for symmetric hot-spots. Increasing the magnetic field strength past the value required to magnetize the electrons is beneficial due to the additional suppression of perturbations by magnetic tension.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Dynamics of laser-generated magnetic fields using long laser pulses

In this work, we report on the experimental investigation of magnetic field generation with a half-loop gold sheet coil driven by long-duration (10 ns) and high-power (0.5 TW) laser pulses. The amplitude of the magnetic field was characterized experimentally using proton deflectometry. The field rises rapidly in the first 1 ns of laser irradiation, and then increases slowly and continuously up to 10 ns during further laser irradiation. The transient dynamics of current shape were investigated with a two-dimensional (2D) numerical simulation that included Ohmic heating of the coil and the resultant change of electrical resistivity determined by the coil material temperature. The numerical simulations show rapid heating at the coil edges by current initially localized at the edges. This current density then diffuses to the central part of the sheet coil in a way that depends both on normal current diffusion as well as temporal changes of the coil resistance induced by the Ohmic heating. The measured temporal evolution of the magnetic field is compared with a model that determines a solution to the coil current and voltage that is consistent with a plasma diode model of the drive region and a 2D simulation of current diffusion and dynamic resistance due to Ohmic heating in the laser coil.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗