Engineering topics

Mooney, James T.

Publications and source records attributed to Mooney, James T..

6 records

NASA NTRS2018

Mirror Design Study for a Segmented HabEx System

NASA is exploring telescope and mirror technology options to meet the demanding science goals of the proposed HabEx space telescope. A key priority for the HabEx mission concept would be to leverage affordable telescope solutions that can meet challenging telescope performance requirements with a demanding program timeline. The baseline approach for HabEx is to use an unobscured, monolithic primary mirror with a coronagraph to optimize system performance. NASA is performing an initial study to investigate the feasibility of a HabEx Lite concept which would not leverage a coronagraph and would therefore, have lower exoEarth yield as a consequence, but could provide system mass, cost, and schedule advantages. The HabEx Lite concept leverages replicated, ULE® mirror segments to provide an attractive, alternative telescope architecture to meet the HabEx threshold mission needs. We present the initial mirror design and performance assessment for the HabEx Lite concept.

Schulz, Kevin↗

NASA NTRS2012

Sub-pixel spatial resolution wavefront phase imaging

A phase imaging method for an optical wavefront acquires a plurality of phase images of the optical wavefront using a phase imager. Each phase image is unique and is shifted with respect to another of the phase images by a known/controlled amount that is less than the size of the phase imager's pixels. The phase images are then combined to generate a single high-spatial resolution phase image of the optical wavefront.

Stahl, H. Philip↗

NASA NTRS2006

Novel In-Space Manufacturing Concepts for the Development of Large Space Telescopes

There is a continuous demand for larger, lighter, and higher quality telescopes. Over the past several decades, we have seen the evolution from launchable 2 meter-class telescopes (such as Hubble), to today s demand for deployable 6 meter-class telescopes (such as JWST), to tomorrow s need for up to 150 meter-class telescopes. As the apertures continue to grow, it will become much more difficult and expensive to launch assembled telescope structures. To address this issue, we are seeing the emergence of new novel structural concepts, such as inflatable structures and membrane optics. While these structural concepts do show promise, it is very difficult to achieve and maintain high surface figure quality. Another potential solution to develop large space telescopes is to move the fabrication facility into space and launch the raw materials. In this paper we present initial in-space manufacturing concepts to enable the development of large telescopes. This includes novel approaches for the fabrication of both the optical elements and the telescope support structure. We will also discuss potential optical designs for large space telescopes and describe their relation to the fabrication methods. These concepts are being developed to meet the demanding requirements of DARPA s LASSO (Large Aperture Space Surveillance Optic) program which currently requires a 150 meter optical aperture with a 17 degree field of view.

Mooney, James T.↗

NASA NTRS2005

Introduction to the Sub-pixel Spatial Resolution Interferometry Process

In this paper we describe a method called "Sub-Pixel Spatial Resolution Interferometry" used to increase the spatial resolution of interferometric measurements of precision optical surfaces. In this process, multiple interferometric measurements are made as the optic under test (or the CCD array)in shifted at sub-pixel increments. The measurements are then combined to construct a measurement with higher spatial resolution than the original measurements. The process will be described and initial results obtained using this process with a commercially available Fizeau interferometer will be presented.

Mooney, James T.↗

NASA NTRS2005

Sub-pixel Spatial Resolution Micro-roughness Measurements with Interlaced Stitching

In this paper we describe a method to increase the spatial resolution of surface micro-roughness measurements. As the surface specifications for precision optics become more demanding, the metrology instruments must cover a broad spatial frequency range. Generally, multiple instruments are used to cover the full range of the specifications. For example, a Fizeau interferometer would be used to test low spatial frequency surface errors, a white light interferometer would be used for mid spatial frequency errors, and an AFM would be used for high spatial frequency errors. For some precision optics, three instruments would be necessary. However, in many applications, an increase in the spatial resolution of a metrology instrument could negate the need for multiple instruments. A solution to increase the spatial resolution of micro-roughness measurements obtained using white light interferometry with "interlaced stitching" will be presented. In "interlaced stitching", multiple interferometric measurements are made as the optic under test (or the CCD array) is laterally shifted at sub-pixel increments. The measurements are then combined to construct a measurement with higher spatial resolution. Initial results obtained while implementing a similar process used to increase the spatial resolution of measurements made with a commercially available Fizeau interferometer will be presented.

Mooney, James T.↗

NASA NTRS2005

Sub-pixel phase-measuring interferometry with interlace stitching

Measurement of mid spatial frequency figure error is critical to large precision optics for missions such as TPF-C. This presentation introduces a technique for increasing the spatial sampling resolution to meet these requirements using conventional video resolution phase-measuring interferometer. Technique involves sub-pixel data shifts, interlaced stitching and PSF deconvolution.

Mooney, James T.↗