Search NASA⌕ Search

Engineering topics

Morgan, David J.

Publications and source records attributed to Morgan, David J..

Versailles Project on Advanced Materials and Standards interlaboratory study on intensity calibration for x-ray photoelectron spectroscopy instruments using low-density polyethylene

We report the results of a Versailles Project on Advanced Materials and Standards interlaboratory study on the intensity scale calibration of x-ray photoelectron spectrometers using low-density polyethylene (LDPE) as an alternative material to gold, silver, and copper. An improved set of LDPE reference spectra, corrected for different instrument geometries using a quartz-monochromated Al Kα x-ray source, was developed using data provided by participants in this study. Using these new reference spectra, a transmission function was calculated for each dataset that participants provided. When compared to a similar calibration procedure using the NPL reference spectra for gold, the LDPE intensity calibration method achieves an absolute offset of ~3.0% and a systematic deviation of ±6.5% on average across all participants. For spectra recorded at high pass energies (≥90 eV), values of absolute offset and systematic deviation are ~5.8% and ±5.7%, respectively, whereas for spectra collected at lower pass energies (<90 eV), values of absolute offset and systematic deviation are ~4.9% and ±8.8%, respectively; low pass energy spectra perform worse than the global average, in terms of systematic deviations, due to diminished count rates and signal-to-noise ratio. Differences in absolute offset are attributed to the surface roughness of the LDPE induced by sample preparation. We further assess the usability of LDPE as a secondary reference material and comment on its performance in the presence of issues such as variable dark noise, x-ray warm up times, inaccuracy at low count rates, and underlying spectrometer problems. In response to participant feedback and the results of the study, we provide an updated LDPE intensity calibration protocol to address the issues highlighted in the interlaboratory study. Finally, we also comment on the lack of implementation of a consistent and traceable intensity calibration method across the community of x-ray photoelectron spectroscopy (XPS) users and, therefore, propose a route to achieving this with the assistance of instrument manufacturers, metrology laboratories, and experts leading to an international standard for XPS intensity scale calibration.

36 MATERIALS SCIENCE↗

XPS guide: Charge neutralization and binding energy referencing for insulating samples

This guide deals with methods to control surface charging during XPS analysis of insulating samples and approaches to extracting useful binding energy information. Furthermore, the guide summarizes the causes of surface charging, how to recognize when it occurs, approaches to minimize charge buildup, and methods used to adjust or correct XPS photoelectron binding energies when charge control systems are used. Additionally, there are multiple ways to control surface charge buildup during XPS measurements and examples of systems on advanced XPS instruments are described. There is no single, simple, and foolproof way to extract binding energies on insulating material, but advantages and limitations of several approaches are described. Because of the variety of approaches and limitations of each it is critical for researchers to accurately describe the procedures that have been applied in research reports and publications.

47 OTHER INSTRUMENTATION↗

Palladium-tin catalysts for the direct synthesis of H 2 O 2 with high selectivity

The direct synthesis of hydrogen peroxide (H 2 O 2 ) from H 2 and O 2 represents a potentially atom-efficient alternative to the current industrial indirect process. We show that the addition of tin to palladium catalysts coupled with an appropriate heat treatment cycle switches off the sequential hydrogenation and decomposition reactions, enabling selectivities of >95% toward H 2 O 2 . This effect arises from a tin oxide surface layer that encapsulates small Pd-rich particles while leaving larger Pd-Sn alloy particles exposed. In conclusion, we show that this effect is a general feature for oxide-supported Pd catalysts containing an appropriate second metal oxide component, and we set out the design principles for producing high-selectivity Pd-based catalysts for direct H 2 O 2 production that do not contain gold.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Band gap engineering of In{sub 2}O{sub 3} by alloying with Tl{sub 2}O{sub 3}

Efficient modulation of the bandgap of In{sub 2}O{sub 3} will open up a route to improved electronic properties. We demonstrate using ab initio calculations that Tl incorporation into In{sub 2}O{sub 3} reduces the band gap and confirm that narrowing of the gap is observed by X-ray photoemission spectroscopy on ceramic surfaces. Incorporation of Tl does not break the symmetry of the allowed optical transitions, meaning that the doped thin films should retain optical transparency in the visible region, in combination with a lowering of the conduction band effective mass. We propose that Tl-doping may be an efficient way to increase the dopability and carrier mobility of In{sub 2}O{sub 3}.

36 MATERIALS SCIENCE↗

Life Cycle Greenhouse Gas Analysis of Advanced Jet Propulsion Fuels: F-T Based SPK-1 Case Study (Report)

In response to the Energy Independence and Security Act (EISA), NETL conducted an LCA (LCA) of 10 fuel production pathways using Fischer-Tropsch synthesis. These pathways use varying combinations of coal and swithgrass feedstocks and two options for carbon management (sequestration or enhanced oil recovery). Only greenhouse gas (GHG) emissions are inventoried. Comparative analysis of the results demonstrate that higher percentages of biomass result in lower life cycle GHG emissions when using switchgrass. The choice of carbon management strategy has an effect on the results.

09 BIOMASS FUELS↗