Engineering topics

Morley, Nicholas J.

Publications and source records attributed to Morley, Nicholas J..

5 records

NASA NTRS1993

Two-dimensional thermal-hydraulics analyses of the Pellet Bed Reactor for Nuclear Thermal Propulsion

Thermal-hydraulics design and analyses of the Pellet Bed Reactor for nuclear thermal propulsion are performed using the nuclear propulsion thermal-hydraulic analysis model to determine the 2D steady-state temperature, pressure, and flow fields in the core and optimize the orificing in the hot-frit to avoid hot spots in the core at full power operation. Results show that by properly adjusting the axial porosity profile in the hot frit, hot spots in the core can be essentially eliminated during full power operation. This important accomplishment is achieved at the expense of slightly larger pressure losses in the core because of flow restriction at the hot frit. However, the overall pressure losses is only about 11 percent of the propellant inlet pressure.

Morley, Nicholas J.↗

NASA NTRS1991

Conceptual studies on the integration of a nuclear reactor system to a manned rover for Mars missions

Multiyear civilian manned missions to explore the surface of Mars are thought by NASA to be possible early in the next century. Expeditions to Mars, as well as permanent bases, are envisioned to require enhanced piloted vehicles to conduct science and exploration activities. Piloted rovers, with 30 kWe user net power (for drilling, sampling and sample analysis, onboard computer and computer instrumentation, vehicle thermal management, and astronaut life support systems) in addition to mobility are being considered. The rover design, for this study, included a four car train type vehicle complete with a hybrid solar photovoltaic/regenerative fuel cell auxiliary power system (APS). This system was designed to power the primary control vehicle. The APS supplies life support power for four astronauts and a limited degree of mobility allowing the primary control vehicle to limp back to either a permanent base or an accent vehicle. The results showed that the APS described above, with a mass of 667 kg, was sufficient to provide live support power and a top speed of five km/h for 6 hours per day. It was also seen that the factors that had the largest effect on the APS mass were the life support power, the number of astronauts, and the PV cell efficiency. The topics covered include: (1) power system options; (2) rover layout and design; (3) parametric analysis of total mass and power requirements for a manned Mars rover; (4) radiation shield design; and (5) energy conversion systems.

El-Genk, Mohamed S.↗

NASA NTRS1991

Estimates of power requirements for a Manned Mars Rover powered by a nuclear reactor

This paper assesses the power requirement for a Manned Mars Rover vehicle. Auxiliary power needs are fulfilled using a hybrid solar photovoltaic/regenerative fuel cell system, while the primary power needs are meet using an SP-100 type reactor. The primary electric power needs, which include 30-kW(e) net user power, depend on the reactor thermal power and the efficiency of the power conversion system. Results show that an SP-100 type reactor coupled to a Free Piston Stirling Engine yields the lowest total vehicle mass and lowest specific mass for the power system. The second lowest mass was for a SP-100 reactor coupled to a Closed Brayton Cycle using He/Xe as the working fluid. The specific mass of the nuclear reactor power system, including a man-rated radiation shield, ranged from 150-kg/kW(e) to 190-kg/KW(e) and the total mass of the Rover vehicle varied depend upon the cruising speed.

Morley, Nicholas J.↗

NASA NTRS1991

Shielding analysis for a manned Mars rover powered by an SP-100 type reactor

Shield design is one of the most crucial tasks in the integration of a nuclear reactor power system to a manned Mars rover. A multilayered W and LiH shield is found to minimize the shield mass and satisfy the dose rate limit of 30 rem/y to the rover crew. The effect on dose rate of tungsten layers thicknesses and position within the lithium hydride shields is investigated. Due to the large cross section for the W (n,gamma) reaction, secondary gammas become a significant radiation source. The man-rated shield mass for the Mars rover vehicle is correlated to the reactor thermal power. The correlation fits to within 9 percent of the calculated shield mass and results in an uncertainty of below 4 percent in the overall rover mass. The shield mass varied from 8600 kg to 20580 kg for a reactor thermal power of 100 to 1000 kW(t), respectively.

Morley, Nicholas J.↗

NASA NTRS1990

Preliminary assessment of the power requirements of a manned rover for Mars missions

A preliminary study to determine the total mass and power requirements of a manned Mars rover is presented. Estimates of the power requirements for the nuclear reactor power system are determined as functions of the number of crew members, the emergency return trip scenario in case of a total malfunction of the reactor system, the cruising speed and range of the vehicle, and the specific mass of the power system. It is shown that the cruising speed of the vehicle and the soil traction factor significantly affect the traversing power requirement and therefore the mass of the nuclear power system. The cruising speed of the vehicle must be limited to 14.5 and 24 km/hr for power system specific masses of 150 kg/kWe and 50 kg/kWe, respectively, for the nuclear power system mass not to exceed 50 percent of the total mass of the rover.

El-Genk, Mohamed S.↗