Hairball and furball tests aka ""beyond the onionskin
Abstract Not Provided
Engineering topics
Publications and source records attributed to Morris, John S.
Abstract Not Provided
Abstract Not Provided
Abstract Not Provided
Abstract Not Provided
Initiation of insensitive high explosive (IHE) formulations requires the use of a booster explosive in the initiation train. Booster material selection is crucial, as the initiation must reliably function across some spectrum of physical parameters. The interest in Diaminoazoxyfurazan (DAAF) for this application stems from the fact that it possesses many traits of an IHE but is shock sensitive enough to serve as an explosive booster. A hemispherical wave breakout test, termed the onionskin test, is one of the methods used to evaluate the performance of a booster material. The wave breakout time-position history at the surface of a hemispherical IHE charge is recorded and the relative uniformity of the breakout can be quantitatively compared between booster materials. A series of onionskin tests were performed to investigate breakout and propagation diaminoazoxyfurazan (DAAF) at low temperatures to evaluate ignition and detonation spreading in comparison to other explosives commonly used in booster applications. Some wave perturbation was observed with the DAAF booster in the onionskin tests presented. The results of these tests will be presented and discussed.
In an effort to increase safety and take advantage of extremely insensitive explosives like TATB, PBXN-7 was developed. It is an integral part of the insensitive munition (IM) effort and has contributed significantly to improvements seen in slow cook-off (SCO). Other explosives exist, while not as insensitive as TATB, which show promise in performance while maintaining insensitivity to common insults. Furazan chemistry developments over the past 30 years have yielded several, and Diaminoazoxyfurazan (DAAF) is one of the forerunners. DAAF has many intriguing properties, which indicated it might be a good fit in formulations designed to replace PBXN-7. A project funded through the Joint Insensitive Munitions Technology Program was launched in 2009 to develop and test formulations containing DAAF and RDX, DAAF and HMX, DAAF and TATB, and DAAF (by itself). All used the same binder, Viton, in 5 weight percent. The testing included performance testing with rate stick, shock sensitivity testing with the IHE gap test, and cold temperature performance testing with rate sticks and front curvature measurements.
Initiation of insensitive high explosive (IHE) formulations requires the use of a booster explosive in the initiation train. Booster material selection is crucial, as the initiation must reliably function across some spectrum of physical parameters. The interest in DAAF for this application stems from the fact that it possesses many traits of an IHE but is shock sensitive enough to serve as an explosive booster. A hemispherical wave breakout test, termed the onionskin test, is one of the methods used to evaluate the performance of a booster material. The wave breakout time-position history at the surface of a hemisphericallHE charge is recorded and the relative uniformity of the breakout can be quantitatively compared between booster materials. A series of onionskin tests were performed to investigate breakout and propagation diaminoazoxyfurazan (DAAF) at low temperatures to evaluate ignition and detonation spreading in comparison to other explosives commonly used in booster applications. Some wave perturbation was observed with the DAAF booster in the onionskin tests presented. The results of these tests will be presented and discussed.
Recent dynamic testing of Diaminoazoxyfurazan (DAAF) has focused on understanding the material properties affecting the detonation propagation, spreading, behavior and symmetry. Small scale gap testing and wedge testing focus on the sensitivity to shock with the gap test including the effects of particle size and density. Floret testing investigates the detonation spreading as it is affected by particle size, density, and binder content. The polyrho testing illustrates the effects of density and binder content on the detonation velocity. Finally the detonation spreading effect can be most dramatically seen in the Mushroom and Onionskin tests where the variations due to density gradients, pressing methods and geometry can be seen on the wave breakout behavior.
While the effects of charge diameter, fuel mix ratio, and temperature on ANFO detonation performance are substantial, the effects of prill type are considerable as well as tailorable. Engineered AN prills provide a means to improve overall performance, primarily by changing the material microstructure through the addition of features designed to enhance hot spot action. To examine the effects of prill type (along with fuel mix ratio and charge diameter) on detonation performance, a series of precision, large-scale, ANFO front-curvature rate-stick tests was performed. Each shot used standard No. 2 diesel for the fuel oil and was essentially unconfined with cardboard confinement. Detonation velocities and front curvatures were measured while actively maintaining consistent shot temperatures. Based on the experimental results, DSD calibrations were performed to model the detonation performance over a range of conditions, and the overall effects of prill microstructure were examined and correlated with detonation performance.
Linear D{sub n}-{kappa} detonation shock dynamics (DSD) filling forms are obtained for four ammonium nitrate-fuel oil (ANFO) mixtures involving variations in the ammonium nitrate prill properties and ANFO stoichiometries. The detonation of ammonium nitrate-fuel oil (ANFO) mixtures is considered to be highly nonideal involving long reaction zones ({approx} several cms), low detonation energies and large failure diameters ({approx} 10s-100s cms). A number of experimental programs have been undertaken to understand ANFO detonation properties as a function of the AN properties [1]-[7]. Given the highly heterogeneous nature of ANFO mixtures (typical high explosive (HE) grade AN prills are porous with a range of diameters) a predictive reactive flow simulation of ANFO detonation will present significant challenges. At Los Alamos, a simulation capability has been developed for predicting the propagation of detonation in non-ideal HE and the work conducted on surrounding materials via a combination of a detonation shock dynamics (DSD) approach and a modified programmed burn method known as the pseudo-reaction-zone (or PRZ) method that accounts for the long detonation reaction zone. In the following, linear D{sub n}-{kappa} DSD fitting forms are obtained for four ammonium nitrate-fuel oil mixtures involving variation in the ammonium nitrate prill properties and ANFO stoichiometries. A detonation shock dynamics calibration for ANFO consisting of regular porous HE grade AN in a 94/6 wt.% AN to FO mix has been obtained in [7].
Recent results utilizing proton radiography (P-Rad) during the detonation of the high explosive PBX 9502 are presented. Specifically, the effects of confinement of the detonation are examined in the LANL detonation confinement sandwich geometry. The resulting detonation velocity and detonation shock shape are measured. In addition, proton radiography allows one to image the reflected shocks through the detonation products. Comparisons are made with detonation shock dynamics (DSD) and reactive flow models for the lead detonation shock and detonation velocity. In addition, predictions of reflected shocks are made with the reactive flow models.
Recently there has been significant interest in evaluating the potential of many different non-ideal energetic materials to cause blast damage. We present a method intended to quantitatively compare the blast loading generated by different energetic materials through use of an explosively driven shock tube. The test explosive is placed at the closed breech end of the tube and initiated with a booster charge. The resulting shock waves are then contained and focused by the tube walls to form a quasi-one-dimensional blast wave. Pressure transducers along the tube wall measure the blast overpressure versus distance from the source and allow the use of the one-dimensional blast scaling relationship to determine the energy deposited into the blast wave per unit mass of test explosive. These values are then compared for different explosives of interest and to other methods of equivalency determination.
We present a simple and inexpensive explosive line wave generator has been designed using commercial sheet explosive and plane wave lens concepts. The line wave generator is constructed using PETN and RDX based sheet explosive for the slow and fast components respectively. The design permits the creation of any desired line width. A series of experiments were performed on a 100 mm design, measuring the detonation arrival time at the output of the generator using a streak camera. An iterative technique was used to adjust the line wave generator's slow and fast components, so as to minimize the arrival time deviation. Designs, test results, and concepts for improvements will be discussed.
We report on the propagation of deflagration waves in the high explosive (HE) PBX 9501 (95 wt % HMX, 5 wt% binder). Our test configuration, which we call the def1agration cylinder test (DFCT), is fashioned after the detonation cylinder test (DTCT) that is used to calibrate the JWL detonation product equation of state (EOS). In the DFCT, the HE is heated to a uniform slightly subcritical temperature, and is ignited at one end by a hot wire. For some configurations and initial conditions, we observe a quasi-steady wave that flares the tube into a funnel shape, stretching it to the point of rupture. This behavior is qualitatively like the DTCT, such that, by invoking certain additional approximations that we discuss, its behavior can be analyzed by the same methods. We employ an analysis proposed by G.I. Taylor to infer the pressure-volume curve for the burning, expanding flow. By comparing this result to the EOS of HMX product gas alone. we infer that only {approx}20 wt% of the HMX has burned at tube rupture. This result confirms pre-existing observations about the role of convective burning in HMX cookoff explosions.