Engineering topics

Morse, S. F. B.

Publications and source records attributed to Morse, S. F. B..

8 records

DOE OSTI2024

Applications of a Rayleigh-Taylor model to direct-drive laser fusion

Here, this paper presents a simple physics-based model for the interpretation of key metrics in laser direct drive. The only input parameters required are target scale, in-flight aspect ratio, and beam-to-target radius, and the importance of each has been quantified with a tailored set of cryogenic implosion experiments. These analyses lead to compact and accurate predictions of the fusion yield and areal density as a function of hydrodynamic stability, and suggest new ways to take advantage of direct drive. To provide examples, we will discuss how the inferred mix width behaves relative to theory, then show how it could be exploited to perform a direct drive implosion with a Lawson metric or Χ no α of 0.24 ± 0.02—using a novel parameter space at high velocities and beam radii on the OMEGA laser—that projects to ignition at a laser energy ≤2.0 MJ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Persistent Hot-Spot Mix in Cryogenic Direct-Drive Fusion Experiments

We show that an x-ray emission signature associated with acceleration phase mass injection correlates with poor experimental hot-spot convergence and a reduced neutron production relative to expectations. It is shown that with increased target mass as well as with higher-design adiabats, this signature is reduced, whereas with increased debris on the target the signature is increased. Here, we estimate that the vapor region in typical best designs may have up to 2x the assumed hydrogen mass at the start of deceleration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Demonstration of a hydrodynamically equivalent burning plasma in direct-drive inertial confinement fusion

Focussing laser light onto the surface of a small target filled with deuterium and tritium implodes it and leads to the creation of a hot and dense plasma, in which thermonuclear fusion reactions occur. In order for the plasma to become self-sustaining, the heating of the plasma must be dominated by the energy provided by the fusion reactions—a condition known as a burning plasma. A metric for this is the generalized Lawson parameter, where values above around 0.8 imply a burning plasma. Here, we report on hydro-equivalent scaling of experimental results on the OMEGA laser system and show that these have achieved core conditions that reach a burning plasma when the central part of the plasma, the hotspot, is scaled in size by at least a factor of 3.9 ± 0.10, which would require a driver laser energy of at least 1.7 ± 0.13 MJ. In addition, we hydro-equivalently scale the results to the 2.15 MJ of laser energy available at the National Ignition Facility and find that these implosions reach 86% of the Lawson parameter required for ignition. Furthermore, our results support direct-drive inertial confinement fusion as a credible approach for achieving thermonuclear ignition and net energy in laser fusion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Demonstration of hot-spot fuel gain exceeding unity in direct-drive inertial confinement fusion implosions

Irradiating a small capsule containing deuterium and tritium fuel directly with intense laser light causes it to implode, which creates a plasma hot enough to initiate fusion reactions between the fuel nuclei. Here we report on such laser direct-drive experiments and observe that the fusion reactions produce more energy than the amount of energy in the central so-called hot-spot plasma. This condition is identified as having a hot-spot fuel gain greater than unity. A hot-spot fuel gain of around four was previously accomplished at the National Ignition Facility in indirect-drive inertial confinement fusion experiments where the capsule is irradiated by X-rays. In that case, up to 1.9 MJ of laser energy was used, but in contrast, our experiments on the OMEGA laser system require as little as 28 kJ. As the hot-spot fuel gain is predicted to grow with laser energy and target size, our work establishes the direct-drive approach to inertial fusion as a promising path towards burning and ignited plasmas in the laboratory. Additionally, we report a record (direct-drive) fusion yield of 0.9 kJ on OMEGA, which we achieved with thin-ice deuterium–tritium liner targets.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Enhanced Laser–Energy Coupling with Small-Spot Distributed Phase Plates (SG5-650) in OMEGA DT Cryogenic Target Implosions

Cryogenic deuterium–tritium ice target implosions on OMEGA with new small-spot ("SG5-650") distributed phase plates (DPP's) achieved an (11 +/- 4)% increase in energy coupling compared to implosions with standard-spot DPP's by decreasing the ratio of the laser spot diameter to the target diameter from 0.93 to 0.75. The SG5-650 DPP's provide a focus spot size of 674 um, which is defined as the diameter that encircles 95% of the measured beam energy compared to 834 um for the SG5-850. The hydrodynamic effciency, defined as the ratio of the kinetic energy in the imploding shell to the laser energy, increased from 4.5% to 5.0% based on radiation-hydrodynamic calculations benchmarked to shell trajectory and bang-time measurements. The higher coupling came with a trade-off of an increased hot-electron production as well as increased hydrodynamic instabilities seeded by a larger mode-10 amplitude from the beam port geometry, both of which may have affected the fusion neutron production and areal density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Direct-drive laser fusion: status, plans and future

Laser-direct drive (LDD), along with laser indirect (X-ray) drive (LID) and magnetic drive with pulsed power, is one of the three viable inertial confinement fusion approaches to achieving fusion ignition and gain in the laboratory. The LDD programme is primarily being executed at both the Omega Laser Facility at the Laboratory for Laser Energetics and at the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory. LDD research at Omega includes cryogenic implosions, fundamental physics including material properties, hydrodynamics and laser–plasma interaction physics. LDD research on the NIF is focused on energy coupling and laser–plasma interactions physics at ignition-scale plasmas. Limited implosions on the NIF in the ‘polar-drive’ configuration, where the irradiation geometry is configured for LID, are also a feature of LDD research. The ability to conduct research over a large range of energy, power and scale size using both Omega and the NIF is a major positive aspect of LDD research that reduces the risk in scaling from OMEGA to megajoule-class lasers. Furthermore, the paper will summarize the present status of LDD research and plans for the future with the goal of ultimately achieving a burning plasma in the laboratory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Optical characterization of the on-target OMEGA focal spot at high energy using the full-beam in-tank diagnostic

The full-beam in-tank (FBIT) diagnostic has been deployed to directly measure the target-plane beam fluence profile, when operated at high energy, of the OMEGA Laser System at the University of Rochester’s Laboratory for Laser Energetics. This article presents the results of early measurements taken with this diagnostic and discusses an improvement that has overcome performance limitations discovered during the initial testing. The diagnostic gives new insight into the ability of the OMEGA Laser System to provide uniform fluence profiles that are consistent across all 60 beams in the laser. Overall, the ultimate goal of the FBIT diagnostic is to allow accurate assessment of the fluence uniformity on a spherical target in 60-beam implosion experiments

47 OTHER INSTRUMENTATION↗

DOE OSTI2020

Novel Hot-Spot Ignition Designs for Inertial Confinement Fusion with Liquid-Deuterium-Tritium Spheres

A new class of ignition designs is proposed for inertial confinement fusion (ICF) experiments. These designs are based on the hot-spot-ignition approach, but instead of conventional targets that comprise of spherical shells with thin frozen deuterium{tritium (DT) layers, homogeneous-density (solid or liquid) DT spheres are used where the lower-density central region and higher-density shell are created dynamically by appropriately shaping the laser pulse. These offer several advantages, including simplicity in target production and lower sensitivity to both laser imprint and physics uncertainty in shock interaction with the ice-vapor interface. The design evolution starts by launching an ~1-Mbar shock into a homogeneous DT sphere. After bouncing from the center, the reflected shock reaches the outer surface of the sphere and the shocked material starts to expand outward until its pressure drops below the ablation pressure. At this point, an adjustment shock is launched inward by supporting ablation pressure. This shock compresses the ablator and fuel, forming a shell. The shell is then accelerated and compressed by appropriately shaping the drive laser pulse, similar to the conventional thin-shell, hot-spot designs. Here, this paper demonstrates the feasibility of the new concept using hydrodynamic simulations and discusses the advantages and disadvantages of the concept compared with more-traditional ICF designs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗