Engineering topics

Morton, J. B.

Publications and source records attributed to Morton, J. B..

At least 19 records

NASA NTRS1981

The deflection of a jet by confining surfaces

Thrust vectoring can be provided by the turning of a jet exhaust by the presence of confining surfaces. This approach is analogous to the upper surface blowing (USB) concept. Mean velocities, velocity autocorrelations, and pressure-velocity correlations are measured. From the autocorrelation curves, the Taylor microscales and the integral length scales are calculated. Convection velocities are calculated from the velocity space-time correlations. Two different confining surfaces (one flat, one with large curvature) are placed adjacent to the lip of a circular nozzle, and the resultant effects on the flow field are determined. In addition, two velocity ratios (exit plane velocity to ambient stream velocity) are examined. The velocity measurements were made with a laser Doppler velocimeter in conjunction with a phase locked-loop processor. Pressure measurements were made using a 1/8th inch condensor type microphone.

Catalano, G. D.↗

NASA NTRS1979

Pressure and velocity measurements in a three-dimensional wall jet

The effects on the flow fields of varying the ratio of the velocity at the exit plane of the nozzle to the outer tunnel flow are reported. The pressure-velocity correlations are taken and some trends are discussed. Emphasis is placed on comparing the coherence between the fluctuating pressure and velocity fields at various locations in the different flow configurations.

Catalano, G. D.↗

NASA NTRS1979

Three component velocity measurements in an upper surface blowing configuration

In four recent papers, results of an experimental investigation of a freely expanding coflowing jet as well as a three dimensional wall jet have been presented. A flat plate and a curved wall surface modelling a wing-flap combination in a high lift V/STOL configuration have been documented as to their effects on the flow field. The ratio of the jet exit plane velocity to the free stream velocity was varied from 5.1 to 10.9 to 1. This report continues the documentation of the three dimensional wall jet with special emphasis on the vertical and lateral mean and fluctuating velocities. Additionally, boundary layer profiles over both the flat plate and the flap are presented.

Catalano, G. D.↗

NASA NTRS1979

Pressure and velocity measurements in a three dimensional wall jet

In three recent papers, some results of an experimental investigation of a freely expanding coflowing jet as well as a three dimensional wall jet have been presented. A flat plate as well as a curved wall surface intended to model a wing-flap combination in a high lift V/STOL configuration have been investigated. In these papers, the ratio of the jet exit plane velocity to the free stream velocity, was 5.1. This paper explores the effects of increasing the velocity ratio. The quantities measured include the width of the mixing region, the mean velocity field, turbulent intensities and time scales. In addition, wall and static pressure-velocity correlations and coherences are presented. The velocity measurements are made using a laser Doppler velocimeter with a phase-locked loop processor. The fluctuating pressures are monitored using condenser-type microphones.

Catalano, G. D.↗

NASA NTRS1979

Turbulence measurements in a three dimensional wall jet

The effects of both a straight and a curved wall on the two-point space-time velocity correlations of a turbulent jet are documented. From the correlations, iso-correlation contours are constructed which allow a picture of the various flow patterns to be determined. Auto and cross-correlations of the fluctuating concentration field are also obtained for the different flow configurations. The confining surfaces served to radically change the flow pattern of the freely expanding turbulent jet. The velocity measurements are made with a laser Doppler velocimeter in conjunction with a phase locked-loop processor, while the concentration field is monitored with a laser light scattering technique.

Catalano, G. D.↗

NASA NTRS1978

Some two-point statistical properties of a three-dimensional wall jet

The effects of both a straight and a curved wall on the two-point space-time velocity correlations of a turbulent jet are documented. From the correlations, isocorrelation contours are constructed which allow a picture of the various flow patterns to be determined. Autoand cross-correlations of the fluctuating concentration field are also obtained for the different flow configurations. The confining surfaces served to radically change the flow pattern for the freely expanding turbulent jet. The velocity measurements are made with a laser Doppler velocimeter in conjunction with a phase locked-loop processor, while the concentration field is monitored with a laser light-scattering technique.

Morton, J. B.↗

NASA NTRS1978

Pressure and velocity measurements in a three dimensional wall jet

A flat plate and a curved wall surface, intended to model a wing-flap combination in a high V/STOL configuration, were used to measure pressure and flow velocity in a freely expanding coflowing jet and a three dimensional wall jet. The effects of increasing the velocity ratio of the jet exit plane velocity to the free stream velocity were investigated. Velocity measurements were made using a two color laser Doppler velocimeter with a phase-locked loop processor. Fluctuating pressures were monitored with condenser-type microphones. Quantities measured include the width of the mixing region, the mean velocity field, turbulent intensities, and time scales. Wall and static pressure-velocity correlations and coherences are presented.

Catalano, G. D.↗

NASA NTRS1978

Unsteady loads due to propulsive lift configurations. Part A: Investigation of scaling laws

This study covered scaling laws, and pressure measurements made to determine details of the large scale jet structure and to verify scaling laws by direct comparison. The basis of comparison was a test facility at NASA Langley in which a JT-15D exhausted over a boilerplater airfoil surface to reproduce upper surface blowing conditions. A quarter scale model was built of this facility, using cold jets. A comparison between full scale and model pressure coefficient spectra, presented as functions of Strouhal numbers, showed fair agreement, however, a shift of spectral peaks was noted. This was not believed to be due to Mach number or Reynolds number effects, but did appear to be traceable to discrepancies in jet temperatures. A correction for jet temperature was then tried, similar to one used for far field noise prediction. This was found to correct the spectral peak discrepancy.

Morton, J. B.↗

NASA NTRS1978

Unsteady loads due to propulsive lift configurations. Part B: Pressure and velocity measurements in a three dimensional wall jet

The effects of increasing the velocity ratio, lambda sub j were explored. The quantities measured include the width of the mixing region, the mean velocity field, turbulent intensities and time scales. In addition, wall and static pressure velocity correlations and coherences are presented. The velocity measurements were made using a laser Doppler velocimeter with a phase locked loop processor. The fluctuating pressures were monitored using condenser type microphones.

Catalano, G. D.↗

NASA NTRS1977

An experimental investigation of a three-dimensional wall jet

An experimental investigation of the effects of a curved and flat wall surface on the flow development of an axisymmetric jet exhausting into a moving airstream has been made. Of primary concern was the comparison of the one-point statistical properties of the unconfined jet to the quantities measured in the flows over a flat plate and a curved wall surface. Quantities measured in this investigation included mean velocities in all three directions, turbulent intensities, autocorrelations, power spectral densities, and intermittencies. The investigation was confined to the near field of the turbulent jet. The curved wall (flap) was found to have a very large effect on both the mean velocity and the turbulent velocity components of the flowfield. The potential core region of the jet was found to break up most rapidly for the flow over the flap. A laser-Doppler velocimeter, using a phase locked-loop processor, was used to make the desired velocity field measurements. To determine the intermittency profiles, a laser light scattering technique was employed.

Catalano, G. D.↗

NASA NTRS1977

Simulation model of erosion and deposition on a barchan dune

Erosion and deposition over a barchan dune near the Salton Sea, California, are modeled by bookkeeping the quantity of sand in saltation following streamlines of transport. Field observations of near surface wind velocity and direction plus supplemental measurements of the velocity distribution over a scale model of the dune are combined as input to Bagnold type sand transport formulas corrected for slope effects. A unidirectional wind is assumed. The resulting patterns of erosion and deposition compare closely with those observed in the field and those predicted by the assumption of equilibrium (downwind translation of the dune without change in size or geometry). Discrepancies between the simulated results and the observed or predicted erosional patterns appear to be largely due to natural fluctuations in the wind direction. The shape of barchan dunes is a function of grain size, velocity, degree of saturation of the oncoming flow, and the variability in the direction of the oncoming wind. The size of the barchans may be controlled by natural atmospheric scales, by the age of the dunes, or by the upwind roughness. The upwind roughness can be controlled by fixed elements or by sand in the saltation. In the latter case, dune scale is determined by grain size and wind velocity.

Howard, A. D.↗

NASA NTRS1976

The interaction of unidirectional winds with an isolated barchan sand dune

Velocity profile measurements are determined on and around a barchan dune model inserted in the roughness layer on the tunnel floor. A theoretical investigation is made into the factors influencing the rate of sand flow around the dune. Flow visualization techniques are employed in the mapping of streamlines of flow on the dune's surface. Maps of erosion and deposition of sand are constructed for the barchan model, utilizing both flow visualization techniques and friction velocities calculated from the measured velocity profiles. The sediment budget found experimentally for the model is compared to predicted and observed results reported. The comparison shows fairly good agreement between the experimentally determined and predicted sediment budgets.

Gad-El-hak, M.↗

NASA NTRS1976

An experimental investigation of an axisymmetric jet in a coflowing airstream

The flow development of an axisymmetric jet exhausting into a moving airstream has been studied. The jet has a Reynolds number of 22,600, and the ratio of the jet velocity to the wind tunnel velocity is 5.1 to 1. The flow field of the axisymmetric jet was examined at locations varying from approximately zero to eight diameters downstream of the orifice. Of primary concern at each downstream location was the mapping of the one point statistical properties of the flow, including mean velocity, turbulent intensity, and intermittency. Autocorrelations and power spectral density curves were determined for both the fluctuating velocity field and the concentration signal at various distances from the jet's center line for different downstream locations. A laser Doppler velocimeter, using a phase locked loop processor, was used to make the desired velocity field measurements which were compared with hot wire anemometer and pressure probe data.

Catalano, G. D.↗

NASA NTRS1976

Measurements in the mixing region of a turbulent jet in a coflowing airstream

The mixing region of a turbulent jet is an important example of an intermittent turbulent shear flow. There are a great deal of interest in this region because of interest in jet noise and STOL aircraft which use upper surface blowing or externally blown flap configurations to increase lift. A detailed study of the one point statistical properties of a smoke laden jet was made using a combination of a laser velocimeter and a light scattering system. The jet, with a 14 to 1 contraction, was placed inside a wind tunnel where the ratio of the jet exit velocity to free stream was 5.1 to 1. All measurements are made for a jet Reynolds number of 22,600. Among the quantities measured are mean axial and radial velocities, axial and radial intensities, power spectra, mean smoke concentration, concentration intensities, concentration spectra, intermittencies and velocity-concentration correlations. The results are compared with hot-wire data where available.

Morton, J. B.↗

NASA NTRS1976

Investigations of scaling laws for jet impingement

The statistical properties of tangential flows over surfaces were investigated by two techniques. In one, a laser-Doppler velocimeter was used in a smoke-laden jet to measure one-point statistical properties, including mean velocities, turbulent intensities, intermittencies, autocorrelations, and power spectral densities. In the other technique, free stream and surface pressure probes connected to 1/8 inch microphones were used to obtain single point rms and 1/3 octave pressures, as well as two point cross correlations, the latter being converted to auto spectra, amplitude ratios, phase lags, and coherences. The results of these studies support the vortex model of jets, give some insights into the effects of surface impingement, and confirm that jet diameter and velocity are the scaling parameters for circular jets, while Reynolds number is relatively unimportant.

Morton, J. B.↗

NASA NTRS1975

Intrepretation of surface features and surface processes on Mars

Eolian erosion and deposition on earth was studied in order to interpret the eolian land forms of Mars. Emphasis of the wind tunnel studies was on the flow field around models of eolian forms. Areas of the wind tunnel studies include: simulation of the atmospheric boundary layer; velocity profile measurements around different models in the desert boundary layer, and estimating shear stress distributions on the model surfaces; flow visualization techniques; streamline mapping using tuft photographs; and roughness contrasts.

Gad-El-hak, M.↗

NASA NTRS1975

Interpretation of lunar heat flow data

Lunar heat flow observations at the Apollo 15 and 17 sites can be interpreted to imply bulk U concentrations for the moon of 5 to 8 times those of normal chondrites and 2 to 4 times terrestrial values inferred from the earth's heat flow and the assumption of thermal steady state between surface heat flow and heat production. A simple model of nearsurface structure that takes into account the large difference in (highly insulating) regolith thickness between mare and highland provinces is considered. This model predicts atypically high local values of heat flow near the margins of mare regions - possibly a factor of 10 or so higher than the global average. A test of the proposed model using multifrequency microwave techniques appears possible wherein heat flow traverse measurements are made across mare-highland contacts. The theoretical considerations discussed here urge caution in attributing global significance to point heat-flow measurements on the moon.

Conel, J. E.↗

NASA NTRS1975

Unsteady loads due to propulsive lift configurations

The flow of a jet over an airfoil representative of upper surface blowing was studied using laser techniques. Experimental techniques were developed for the investigation of unsteady pressures behind a cold model jet. Construction of a 1/4 scale model of the 'Beach' test configuration was completed along with construction of a portable detector. The portable detector is used in conjunction with a laser to measure jet flows during tests on the 'Beach' facility. The detector incorporates both optical and electronic components.

Morton, J. B.↗