Search NASA⌕ Search

Engineering topics

Moutinho, Helio R.

Publications and source records attributed to Moutinho, Helio R..

16 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Characterization of n-Type Iodine-Doped and Indium-Doped CdTe/Cd-Se-Te Thin Films Fabricated by Close-Spaced Sublimation Epitaxy

In this study, n-type CdTe thin films, specifically iodine-doped CdTe (CdTe:I), indium-doped CdTe (CdTe:In), and indium-doped Cd-Se-Te (CST:In), were synthesized using close-spaced sublimation epitaxy (CSSE). Characterization techniques secondary ion mass spectrometry (SIMS), electron backscatter diffraction (EBSD), Hall-effect measurements, and time-resolved photoluminescence (TRPL) were employed to analyze the chemical, structural, and electronic properties of these materials. The results indicated epitaxial single crystal CSSE films grew on the single crystal substrates, with carrier density ranging from 10^14 - 10^16 cm -3 , and after post-annealing, the minority-carrier lifetimes reach near the radiative limit. Additionally, a preliminary exploration of homojunction structures with an n- type (CdTe:In /CST:In /CdTe:I) /CdTe:P /Cu /Mo configuration was performed. The best device performance was achieved with CdTe:I including CdS aiding in band alignment, resulting in a power conversion efficiency (..eta..) of 2.61% with open circuit voltage (Voc) of 850 mV, fill factor (FF) of 47.8%, and short-circuit current (Jsc) of 6.44 mA/cm 2 . The observed low Jsc and efficiency may be attributed to a buried junction and a poor interface, due to dopant interdiffusion. Consequently, further investigations focusing on interface optimization, diffusion blocking, and reduced recombination through passivation, are crucial to enhancing the efficiency of CSSE CdTe homojunction devices in the future.

cadmium compounds↗
DOE OSTI2023

Degradation-related defect level in weathered silicon heterojunction modules characterized by deep level transient spectroscopy

Commercial silicon heterojunction photovoltaic modules, known as amorphous-silicon-based heterojunction with intrinsic thin-film layer (HIT) modules, show average degradation after 10 years in the field. HIT modules weathered outdoors in Colorado and Florida display mostly uniform decreases in intensity when mapped with photoluminescence (PL) imaging compared to a control module. Flash-table-based current-voltage curves show that degradation is dominated by voltage loss. Samples are cored from each of the modules, and deep level transient spectroscopy (DLTS) detects three electron-trap defect states in all modules with activation energies of electron emission from the defects of 0.07, 0.16, and 0.50 eV. DLTS measurements on the weathered modules show an additional deep-level, electron-trap defect state with an activation energy of 0.51 eV and a trap density of approximately 10 12 cm –3 . The capture rate is measured using varying short filling pulse times, and the resulting capture cross section is estimated to be 1.1x10 –16 cm 2 . The development of the weathering-related defect level correlates to decreases in carrier lifetime, PL intensity, and module voltage. Various depths of the space charge region are probed with increments in applied reverse bias and filling-pulse bias. Furthermore, this DLTS depth profiling shows a trend of trap density increasing with less applied reverse bias, suggesting that the weathering-related defect increases carrier recombination toward the interface between the bulk silicon wafer and the junction-forming amorphous-silicon passivation layers.

14 SOLAR ENERGY↗
DOE OSTI2023

Molecular Beam Epitaxy of Monocrystalline GaAs on Water-Soluble NaCl Thin Films

The goal of this project was to demonstrate the feasibility of employing an epitaxial NaCl thin film as a water-soluble release layer for III-V photovoltaic devices and GaAs substrate reuse. Over the course of this project efforts were focused on: 1) achieving crystalline NaCl thin films on GaAs (100) substrate, 2) exploring the growth parameters for subsequent GaAs on NaCl thin films in effort to improve crystallinity of the semiconductor layer, 3) deposition and removal of single crystalline solar cell devices from the parent substrate, and 4) improving morphology and reducing large scale defects in the removed layers to fabricate a working a solar cell device. There was no previous work on direct integration of GaAs/NaCl/GaAs heterostructures at the time of this study. We used molecular beam epitaxy (MBE) to deposit both the alkali halide salt and subsequent III-V material in the same chamber, with no vacuum break. Single crystalline GaAs films were achieved on NaCl layers through careful tuning of the growth parameters and exposure to the reflection high energy electron diffraction (RHEED) beam. Dissolution of the NaCl layer in water provided rapid release of the semiconductor layer from the substrate. Monocrystalline solar cells were grown on the III-V templates using MBE and dynamic hydride vapor phase epitaxy (HVPE). However, the extended time at elevated temperatures required for the cell growth resulted in large area defects from fusion of the semiconductor overlayer to the substrate, causing shorts in fabricated devices. By changing the way that the template layer was grown, the density of these defects could be reduced. Unfortunately, the defects were not reduced to a level allowing for fabrication of a working device.

14 SOLAR ENERGY↗
DOE OSTI2022

Nanometer-Scale Measurement of Grid Finger Electrical Conduction Pathways to Detect Series Resistance Degradation of Utility-Scale Silicon Solar Cells

Here, we report on an electrical conduction mechanism for series resistance (Rs) degradation observed in a utility-scale photovoltaic power plant by imaging the local resistance at the Ag/Si interface of the c-Si front metallization. Scanning spreading resistance microscopy imaging with nanometer (nm) scale spatial resolution revealed that the number of point or small-area electrical contacts decreased substantially in a degraded cell compared to an unaffected cell, demonstrating the root cause of Rs degradation. The decrease in electrical contacts is likely caused by a structural change - the Ag particles in contact with the Si cell (or via a nm-thickness tunneling glass layer) aggregate into bulk Ag, and a highly resistive glass frit forms a belt shape at the Ag/Si interface. This resistive belt, with a thickness of ~1 um, blocks the current conduction from the cell emitter to the Ag grid. Our microscopy results help to unravel unambiguously the degradation mechanism and demonstrate an example of the multiscale characterization approach for understanding degradation in field-weathered PV module.

14 SOLAR ENERGY↗
DOE OSTI2022

Local nm-Scale Imaging of Electrical Contact for Series Resistance Degradation of Silicon Solar Cells

We report on an electrical conduction mechanism for series resistance (Rs) degradation observed in a utility scale solar farm by nm-scale imaging of the local resistance at the Ag/Si interface of c-Si cell front metallization. Our previous work showed that the I-V measurement of individual cells demonstrated exclusively the cell Rs degradation, and the "beads pattern" of electroluminescence indicated the degradation at the Ag grid of front metallization. Scanning spreading resistance microscopy (SSRM) imaging, which is based on the contact mode of atomic force microscopy and taken on the cross-sections of Ag/Si contact, revealed the electrical conduction pathway of Ag particles in point or small area contact with Si cell emitter. The SSRM results illustrated that the number of electrical contacts in the degraded cell decreased largely compared with the unaffected cell, demonstrating the direct cause of the Rs degradation. This reduction in electrical contact in the degraded cell could be caused by a structural change in the Ag grid during long-term field service: The Ag particles in contact with Si aggregate into the Ag bulk and a highly resistive ceramic oxide is formed in a "belt" shape at the Ag/Si interface. This resistive belt with a thickness of ~1 m blocks the current conduction from cell emitter to the Ag grid. The degraded cell shows both a morphological and chemical difference in the screen-printed finger contact compared to the unaffected cell, which likely caused the different degradation susceptibility during the long-term field service. Our results demonstrate an example of the multi-scale characterization approach for understanding photovoltaic degradation mechanisms.

ENGINEERING,SOLAR ENERGY↗
DOE OSTI2022

Metastability and Degradation of CdTe Solar Cells Investigated by nm-Scale Electrical Potential Imaging

We report on investigations of reversible metastability and irreversible degradation of MZO/CdSeTe/CdTe devices from the perspective of electric field across the device using Kelvin probe force microscopy (KPFM). The device showed reversible transitions between the light-soak state (LSS) with the best device efficiency and the dark-soak state (DSS) with an inferior efficiency. However, it showed an irreversible degradation state (DgS) driven by long-hour light soaking at an elevated temperature. The nm-scale KPFM electric field imaging on cross-sections of the devices revealed different anomalous electric field profiles. The electric field at the LSS exhibits a main peak inside the CdSeTe layer but not at the MZO/CdSeTe heterointerface, demonstrating that working junction of the device is a buried homojunction (BHJ). At the DSS, a second electric field peak was observed at the MZO/CdSeTe interface with a similar strength to the main BHJ, which probably caused the decrease in fill factor at the DSS. At the DgS, the electric field peak at the MZO/CdSeTe interface increased significantly and a third electric field was measured at the back contact of the device. Device modeling using COMSOL and in alignment with both the electric field and device current-voltage curves suggest that a slightly low n-doped CdSeTe in the region near the MZO/CdSeTe interface caused the BHJ, and that either a loss of MZO doping or increase of the conduction band offset spike due to long-term stress caused the fill factor-dominated degradation and the increased electric field near the MZO/CdSeTe interface at the DgS. The former, MZO doping decrease, is more plausible by referring the related literature.

BHJ↗
DOE OSTI2022

Molecular beam epitaxy of GaAs templates on water soluble NaCl thin films

Expensive III-V substrates are cost limiting for the adoption of many technologies. Consequently, being able to reuse the original substrate is highly desirable. Existing substrate reuse techniques have significant drawbacks, but this work discusses a new method using molecular beam epitaxy deposition of water soluble NaCl thin films on commonly employed (0 0 1) GaAs substrates. Single-crystal GaAs templates are grown on continuous NaCl layers utilizing careful exposure of the NaCl to an in-situ electron beam and a low temperature nucleation layer. The template layers can be quickly removed from the substrate via dissolution of the NaCl. After liftoff, the original wafer shows an increase in rms surface roughness of only 0.2 nm.

14 SOLAR ENERGY↗
DOE OSTI2022

Electrical Potential Investigation of Reversible Metastability and Irreversible Degradation of CdTe Solar Cells

In this paper, we report on the stability of CdTe devices with a structure of TCO/MZO/CdSeTe/CdTe/back-contact. The device showed reversible transitions between the light-soak state (LSS) with the best device efficiency and the dark-soak state (DSS) with an inferior efficiency. However, it showed an irreversible degradation state (DgS) driven by long-hour light soaking at an elevated temperature. We have investigated transitions between these three states from the perspective of the electric field by nm-resolution potential imaging across the devices using Kelvin probe force microscopy (KPFM). The results exhibit different anomalous electric field profiles. At the LSS, the electric field exhibits a main peak inside the CdSeTe layer instead of the MZO/CdSeTe heterointerface, illustrating a buried homojunction (BHJ) of the device. At the DSS, a large electric field peak at the MZO/CdSeTe interface was measured, which probably resulted in the inferior fill factor at the DSS. At the DgS, the electric field peak at the MZO/CdSeTe interface increased further and a third electric field was measured at the back contact of the device. Device modeling using COMSOL software, in alignment with both the electric field and device current-voltage curves, elucidates that a low n-doped CdSeTe in the region near the MZO/CdSeTe interface caused the BHJ in the LSS and a loss of MZO doping and/or increase of the conduction band offset spike due to long-term stress caused the increased electric field near the MZO/CdSeTe interface at the DgS.

CdTe solar cell↗
DOE OSTI2022

Potential-induced degradation of Cu(In,Ga)Se 2 can occur by shunting the front i-ZnO and by damaging the p-n junction

In this work we test field-relevant potential-induced degradation (PID) behavior by encapsulating laboratory Cu(In,Ga)Se 2 (CIGS) solar cells and applying +1000 V uniformly on the face of the front glass. In this configuration, we find that K-rich borosilicate glass reduces the extent of PID relative to Na-rich soda-lime glass. We also find that the standard testing protocol of stressing cells at short-circuit leads to faster PID than stressing cells at open-circuit. We characterize two types of CIGS PID: The first, front shunting PID, is driven by front-glass stress and occurs when alkali metal cations accumulate in the i-ZnO buffer, where they increase shunt conductance to reduce fill factor. The second, p-n junction PID, results from back-glass stress as alkali metal cations pile up near the CIGS surface/CdS buffer, where they reduce charge carrier concentration, open-circuit voltage, and fill factor to degrade efficiency ~160 times faster than front shunting PID.

14 SOLAR ENERGY↗
DOE OSTI2021

Application of electron backscatter diffraction techniques to quantify effects of aging on sub-grain and spatial heterogeneity in NMC cathodes

Identification and evaluation of structural heterogeneity in spent cathode materials is crucial to developing appropriate remediation strategies for novel recycling processes. Native heterogeneities may be exacerbated during the cell's operational lifetime, as sub-particle-scale variations induce anisotropic expansion and contraction upon cycling. Structural transformations resulting from repeated cycling and calendar aging predominantly occur at the secondary particle surface and at the grain boundaries (GBs) between primary particles. However, the diffusion and stress build up around and across GBs are poorly understood. In this study, electron backscatter diffraction (EBSD) is employed to track sub-grain lattice structure across a statistically relevant number of Li(Ni0.33Mn0.33Co0.33)O2 (NMC-111) particles. Specifically, differences in lattice misorientation – measured as the deviation from the grain's average orientation – are tracked as a function of position within the electrode (near current collector, middle, and near separator) and as a function of electrochemical cycling. Further, a novel method of structural analysis is developed, offering insight into sub-grain diffusion behavior by comparing lattice misorientation near the grain boundary versus in the grain bulk. The present results suggest that electrode-scale spatial heterogeneity in lattice structure is induced by initial manufacturing conditions, and that radial gradients in lattice misorientation evolve at the primary particle scale with repeated electrochemical cycling.

25 ENERGY STORAGE↗
DOE OSTI2021

Local Resistance Measurement for Degradation of c-Si Heterojunction with Intrinsic Thin Layer (HIT) Solar Modules

Silicon heterojunction with intrinsic thin layer (or HIT) modules typically degrade at a rate of less than 1% annually in solar fields with dominant degradation in open-circuit voltage and some degradation in series resistance. However, detailed mechanisms can differ from module to module. Here, we study increases in local series resistance that occur over long-term field deployment, indicated by cell areas where the photoluminescence intensity does not degrade but the electroluminescence degrades significantly. To directly measure the local series resistance, we have cored out the local electroluminescence-degraded area, and we measured the sheet resistance by 4-point-probe and local nm-scale resistance using scanning spreading resistance microscopy (SSRM). The results by 4-point-probe show scattered sheet resistance that can be caused, for example, by nonuniform current paths through the transparent conductive oxide layer, the a-Si:H emitter, or the near-junction c-Si inversion layer. In contrast, the SSRM results indicate a relatively uniform and non-degraded resistivity on smaller nanometer spatial scales. SSRM is an atomic force microscopy-based two-terminal resistance mapping technique that measures the local resistance in nm-volume beneath the probe. The consistent resistances measured on the control and degraded samples can exclude the degradation of transparent conductive oxide resistance.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2020

Se diffusion in CdTe thin films for photovoltaics

Manipulating CdSeTe bandgrading to enhance photocurrent and carrier lifetime is an essential part of high-performance CdTe photovoltaics (PVs). Here, we examine Se diffusion kinetics in single-crystal and polycrystalline CdTe during deposition, thermal annealing, and CdCl 2 treatments. Se distributions are determined by dynamic secondary-ion-mass spectroscopy and Auger electron spectroscopy depth profiling and coupled with electron backscatter diffraction images of the crystalline structure. Effective bulk and grain boundary diffusion coefficients are determined by analytical models and discussed in the context of processing and film morphology. Se is found to diffuse in CdTe at much higher rates during CdCl 2 treatments than with thermal processing alone. GB diffusion also occurs at a significantly faster rate than bulk diffusion. As a result of these two effects, the near interface bulk and GB Se diffusion during CdCl 2 treatments dominates the bandgrading profiles in CdTe PVs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

High Efficiency Silicon Module Degradation - From Atoms to Systems: Preprint

For PV to be cost competitive with traditional energy sources reliability is of critical importance. Historically, PV reliability has focused on the module packaging because degradation and failure modes were directly linked to the packaging. Today, in addition to module packaging cell related reliability issues can be observed. We show that silicon heterojunction (SHJ) degradation is directly linked to the re-distribution of hydrogen (H) near the interface between the amorphous-silicon (a-Si) and silicon bulk. PERC modules show a similar decline in carrier lifetime indicating that not the packaging but the cells are also changing during field exposure. Examination of a stressed PERC cell showed a similar H redistribution in the cell. Understanding the degradation mechanism at the atomic level is important in facilitating possible mitigating mechanisms and more accurately projecting performance.

degradation↗
DOE OSTI2020

Thin-Film Solar Cells with 19% Efficiency by Thermal Evaporation of CdSe and CdTe

CdTe-based solar cells exhibiting 19% power conversion efficiency were produced using widely available thermal evaporation deposition of the absorber layers on SnO2-coated glass with or without a transparent MgZnO buffer layer. Evaporating CdSe and CdTe sequentially by thermal evaporation and subsequent CdCl2 annealing establishes efffective CdSeTe band grading as well as dense, large-grain films. These results show that high-performance II-VI photovoltaics can be made by inexpensive, commercially available evaporation systems without the need to build customized equipment, enabling CdTe photovoltaics research and manufacturing to be more accessible to the broader photovoltaics community.

14 SOLAR ENERGY↗