Search NASA⌕ Search

Engineering topics

Mueller, D.

Publications and source records attributed to Mueller, D..

At least 37 records · Page 2

The Physics of Tokamak Start-up

Tokamak start-up on present-day devices usually relies on inductively induced voltage from a central solenoid. In some cases inductive startup is assisted with auxiliary power from electron cyclotron radio frequency heating. ITER, the National Spherical Torus eXperiment Upgrade and JT60, now under construction, will make use of the understanding gained from present-day devices to ensure successful start-up. Design of a spherical tokamak (ST) with DT capability for nuclear component testing would require an alternative to a central solenoid because the small central column in an ST has insufficient space to provide shielding for the insulators in the solenoid. Alternative start-up techniques such as induction using outer poloidal field coils, electron Bernstein wave start-up, coaxial helicity injection and point source helicity injection have been used with success, but require demonstration of scaling to higher plasma current.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Disruptions, Disruptivity, and Safer Operating Windows in the High-β Spherical Torus NSTX

This paper discusses disruption rates, disruption causes, and disruptivity statistics in the high- βN National Spherical Torus Experiment (NSTX) [M. Ono, et al. Nuclear Fusion 40, 557 (2000)]. While the overall disruption rate is rather high, configurations with high βN , moderate q*, strong boundary shaping, sufficient rotation, and broad pressure and current profiles are found to have the lowest disruptivity; active n=1 control further reduces the disruptivity. The disruptivity increases rapidly for q*<2.7, which is substantially above the ideal MHD current limit. In quiescent conditions, q min >1.25 is generally acceptable for avoiding the onset of core rotating n=1 kink/tearing modes; when EPM and ELM disturbances are present, the required q min for avoiding those modes is raised to ~1.5. The current ramp and early flat-top phase of the discharges are prone to n=1 core rotating modes locking to the wall, leading to a disruption. Small changes to the discharge fueling during this phase can often mitigate the rotation damping associated with these modes and eliminate the disruption. The largest stored energy disruptions are those that occur at high current when a plasma current rampdown is initiated incorrectly.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Implementation of β N Control in the National Spherical Torus Experiment

We have designed and constructed a system for control of the normalized B in the National Spherical Torus Experiment [M. Ono, et al., Nuclear Fusion 40, 557 (2000)]. A PID operator is applied to the difference between the present value of B N (from realtime equilibrium reconstruction) and a time-dependent request, in order to calculate the required injected power. This injected power request is then turned into modulations of the neutral beams. The details of this algorithm are described, including the techniques used to develop the appropriate control gains. Example uses of the system are shown

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Generation Of High Non-inductive Plasma Current Fraction H-mode Discharges By High-harmonic Last Wave Heating In The National Spherical Torus Experiment

1.4 MW of 30 MHz high-harmonic fast wave (HHFW) heating, with current drive antenna phasing, has generated a Ip = 300kA, BT (0) = 0.55T deuterium H-mode plasma in the National Spherical Torus Experiment that has a non-inductive plasma current fraction, fNI = 0.7-1. Seventy-five percent of the non-inductive current was generated inside an internal transport barrier that formed at a normalized minor radius, r/a ~ 0.4 . Three quarters of the non-inductive current was bootstrap current and the remaining non-inductive current was generated directly by HHFW power inside r/a ~ 0.2.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Lidar Measurements for Desert Dust Characterization: An Overview

We provide an overview of light detection and ranging (lidar) capability for describing and characterizing desert dust. This paper summarizes lidar techniques, observations, and fallouts of desert dust lidar measurements. The main objective is to provide the scientific community, including non-practitioners of lidar observations with a reference paper on dust lidar measurements. In particular, it will fill the current gap of communication between research-oriented lidar community and potential desert dust data users, such as air quality monitoring agencies and aviation advisory centers. The current capability of the different lidar techniques for the characterization of aerosol in general and desert dust in particular is presented. Technical aspects and required assumptions of these techniques are discussed, providing readers with the pros and cons of each technique. Information about desert dust collected up to date using lidar techniques is reviewed. Lidar techniques for aerosol characterization have a maturity level appropriate for addressing air quality and transportation issues, as demonstrated by some first results reported in this paper

Mona, L.↗

Plasma Modeling Results and shape control improvements for NSTX

New control implementations and dynamics studies on the National Spherical Torus eXperiment (NSTX) are summarized. In particular, strike point (SP) position, X-point height and squareness control, and two new system-identification methods / control-tuning algorithms were put into operation.The PID controller for the SP was tuned by analyzing the step response of the SP position to the poloidal coil currents, employing the Ziegler-Nichols method. The resulting SP controller was successfully employed to achieve the “snowflake” divertor configuration in NSTX. An offline system identification of the plasma response to the control inputs based on ARMAX input-output models was implemented. With this tool, rough estimates of the improvements were realized and several control improvements were identified.An online automatic relay-feedback PID tuning algorithm was implemented, which has the advantage of tuning the controller in one shot, thus optimizing the use of experimental time. Furthermore, using these new capabilities, we implemented LLD scenarios with control for theall four upper/lower/inner/outer SPs and with a combined X-point height, SP radius control. Separately, an independent squareness control was implemented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Be/X-Ray Binary A0535+26 During Its Recent 2009/2010 Outbursts

The Be/X-ray binary A0535+26 showed a giant outburst in December 2009 that reached approximately 5.14 Crab in thc 15-50 keV range. Unfortunately, due to Sun constraints it could not be observed by most X-ray satellites. The outburst was preceded by four weaker outbursts associated with the periastron passage of the neutron star. The fourth of them, in August 2009, presented a peculiar double-peaked light curve, with a first peak lasting about 9 days that reached a (15- 50 keV) flux of 440 mCrab. The tl ux then decreased to less than 220 mCrab, and increased again reaching 440 mCrab around the periastron. The outburst was monitored with INTEGRAL, RXTE, and Suzaku TOO observations. One orbital period (approximately 111 days) after the 2009 giant outburst, a new and unexpectedly bright outburst took place (approximately 1.4Crab in the 15-50 keV range). It was monitored with TOO observations with INTEGRAL, RXTE, Suzaku, and Swift. First results of the spectral and timing analysis of these observations are presented. with a specific focus on the cyclotron lines present in thc system and its variation with the mass accretion rate.

Caballero, I.↗

Recent progress toward an advanced spherical torus operating point in NSTX

Progress in the development of integrated advanced ST plasma scenarios in NSTX (Ono et al., 2000 Nucl. Fusion 40 557) is reported. Recent high-performance plasmas in NSTX following lithium coating of the plasma facing surfaces have achieved higher elongation and lower internal inductance than previously. Analysis of the thermal confinement in these lithiumized discharges shows a stronger plasma current and weaker toroidal field dependence than in previous ST confinement scaling studies; the ITER-98(y, 2) scaling expression describes these scenarios reasonably well. Analysis during periods free of MHD activity has shown that the reconstructed current profile can be understood as the sum of pressure driven, inductive and neutral beam driven currents, without requiring any anomalous fast-ion transport. Non-inductive fractions of 65–70%, and βP > 2, have been achieved at lower plasma current. Some of these low-inductance discharges have a significantly reduced no-wall βN limit, and often have βN at or near the with-wall limit. Coupled m/n = 1/1 + 2/1 kink/tearing modes can limit the sustained β values when rapidly growing ideal modes are avoided. A βN controller has been commissioned and utilized in sustaining high-performance plasmas. 'Snowflake' divertors compatible with high-performance plasmas have been developed. Scenarios with significantly larger aspect ratios have also been developed, in support of next-step ST devices. Furthermore, these NSTX plasmas have many characteristics required for next-step ST devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Demonstration of 300 kA CHI-startup current, coupling to transformer drive and flux savings on NSTX

Discharges formed by transient coaxial helicity injection (CHI) in the National Spherical Torus Experiment (NSTX) have attained peak currents of 300 kA for the first time. CHI-started discharges are coupled to induction, and ramped up to over 1 MA. Up to an additional 400 kA of toroidal current is produced, compared with discharges with the same inductive drive without CHI. These CHI-inductively coupled discharges demonstrate flux savings over standard NSTX inductive-only discharges, requiring significantly less transformer flux to reach 1 MA of toroidal current, as well as exhibiting higher elongation and lower internal inductance. These results indicate the potential for substantial current generation capability by CHI in NSTX and in future toroidal devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Pedestal characterization and stability of small-ELM regimes in NSTX

An instability near the plasma edge known as the edge harmonic oscillation (EHO) is thought to enable access to the ELM-free quiescent H-mode (QH-mode) in tokamaks, which is a highly desirable operational regime for ITER because of the avoidance of periodic ELM heat loads. The EHO has been hypothesized to be a saturated kink driven unstable by toroidal rotational shear that provides sufficient transport near the plasma edge to keep the edge plasma below the peeling-ballooning stability limit. NSTX has observed unstable modes with similar characteristics to the EHO coincident with transition to a small-ELM regime (called Type-V). These small ELMs do not have a measurable effect on the plasma stored energy (< 1%). Transition to this regime is associated with a downward biased plasma as evidenced by drsep < -5 mm. Soft x-ray emission indicates that these modes are localized just inside the pedestal and are correlated with increased density fluctuations in the pedestal as measured by microwave reflectometry. The lowest order mode rotates at the plasma rotation frequency, indicating n=1, and harmonics up to n=6 have been observed simultaneously with the n=1, as determined by the rotation frequency of the higher harmonics. Increased edge collisionality is required to access Type-V ELMs. Stability analysis during the observed modes indicates instability to n=1-3 with n=3 having the highest growth rate and unstable mode eigenfunctions peaked near the plasma edge. Discharges with Type-V and Type-I ELMs are both calculated to be on the peeling unstable side of the peeling ballooning stability curve, with the Type-V case at higher normalized pressure gradient.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reduction of low-Z impurities during plasma start-up

Reduction of low-Z impurities is essential during the plasma start-up in tokamaks. For plasma start-up using the method of Coaxial Helicity Injection (CHI) it has been found here that conventional wall conditioning methods have been inadequate to generate a plasma with acceptably low levels of low-Z impurities. NSTX has now used a new combination of techniques to improve CHI start-up performance. These are the use of high-current discharge cleaning of the lower divertor surfaces, which function as the CHI electrodes, to remove loosely bound impurities, controlling the poloidal magnetic field to avoid plasma wall contact and the use of evaporated lithium coatings of the electrodes and other plasma-facing surfaces. Together, these techniques have enabled significant improvement in NSTX CHI performance leading to a saving of central solenoid flux and the first observation of electron temperatures during CHI exceeding the oxygen radiation barrier temperature.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Strike Point Control for the National Spherical Torus Experiment (NSTX)

This paper presents the first control algorithm for the inner and outer strike point position for a Spherical Torus (ST) fusion experiment and the performance analysis of the controller. A liquid lithium divertor (LLD) will be installed on NSTX which is believed to provide better pumping than lithium coatings on carbon PFCs. The shape of the plasma dictates the pumping rate of the lithium by channeling the plasma to LLD, where strike point location is the most important shape parameter. Simulations show that the density reduction depends on the proximity of strike point to LLD. Experiments were performed to study the dynamics of the strike point, design a new controller to change the location of the strike point to desired location and stabilize it. The most effective PF coils in changing inner and outer strike points were identified using equilibrium code. The PF coil inputs were changed in a step fashion between various set points and the step response of the strike point position was obtained. From the analysis of the step responses, PID controllers for the strike points were obtained and the controller was tuned experimentally for better performance. The strike controller was extended to include the outer-strike point on the inner plate to accommodate the desired low outer-strike points for the experiment with the aim of achieving "snowflake" divertor configuration in NSTX.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Pedestal Characterization and Stability of Small-ELM Regimes in NSTX

An instability near the plasma edge known as the edge harmonic oscillation (EHO) is thought to enable access to the ELM-free quiescent H-mode (QH-mode) in tokamaks, which is a highly desirable operational regime for ITER because of the avoidance of periodic ELM heat loads. The EHO has been hypothesized to be a saturated kink driven unstable by toroidal rotational shear that provides sufficient transport near the plasma edge to keep the edge plasma below the peeling-ballooning stability limit. NSTX has observed unstable modes with similar characteristics to the EHO coincident with transition to a small-ELM regime (called Type-V). These small ELMs do not have a measurable effect on the plasma stored energy (< 1%). Transition to this regime is associated with a downward biased plasma as evidenced by drsep < -5 mm. Soft x-ray emission indicates that these modes are localized just inside the pedestal and are correlated with increased density fluctuations in the pedestal as measured by microwave reflectometry. The lowest order mode rotates at the plasma rotation frequency, indicating n=1, and harmonics up to n=6 have been observed simultaneously with the n=1, as determined by the rotation frequency of the higher harmonics. Increased edge collisionality is required to access Type-V ELMs. Stability analysis during the observed modes indicates instability to n=1-3 with n=3 having the highest growth rate and unstable mode eigenfunctions peaked near the plasma edge. Discharges with Type-V and Type-I ELMs are both calculated to be on the peeling unstable side of the peeling ballooning stability curve, with the Type-V case at higher normalized pressure gradient.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Evaporated Lithium Surface Coatings in NSTX

Two lithium evaporators were used to evaporate more than 100 g of lithium on to the NSTX lower divertor region. Prior to each discharge, the evaporators were withdrawn behind shutters, where they also remained during the subsequent HeGDC applied for periods up to 9.5 min. After the HeGDC, the shutters were opened and the LITERs were reinserted to deposit lithium on the lower divertor target for 10 min, at rates of 10-70 mg/min, prior to the next discharge. The major improvements in plasma performance from these lithium depositions include: 1) plasma density reduction as a result of lithium deposition; 2) suppression of ELMs; 3) improvement of energy confinement in a low-triangularity shape; 4) improvement in plasma performance for standard, high-triangularity discharges; 5) reduction of the required HeGDC time between discharges; 6) increased pedestal electron and ion temperature; 7) reduced SOL plasma density; and 8) reduced edge neutral density.

10100 Impurities↗

Overview of Results from the National Spherical Torus Experiment (NSTX)

The mission of NSTX is the demonstration of the physics basis required to extrapolate to the next steps for the spherical torus (ST), such as a plasma facing component test facility (NHTX) or an ST based component test facility (ST-CTF), and to support ITER. Key issues for the ST are transport, and steady state high β operation. To better understand electron transport, a new high-k scattering diagnostic was used extensively to investigate electron gyro-scale fluctuations with varying electron temperature gradient scale-length. Results from n = 3 braking studies are consistent with the flow shear dependence of ion transport. New results from electron Bernstein wave emission measurements from plasmas with lithium wall coating applied indicate transmission efficiencies near 70% in H-mode as a result of reduced collisionality. Improved coupling of High Harmonic Fast-Waves has been achieved by reducing the edge density relative to the critical density for surface wave coupling. In order to achieve high bootstrap current fraction, future ST designs envision running at very high elongation. Plasmas have been maintained on NSTX at very low internal inductance l i ~0.4 with strong shaping (κ ~ 2.7, δ ~ 0.8) with β N approaching the with-wall beta limit for several energy confinement times. By operating at lower collisionality in this regime, NSTX has achieved record non-inductive current drive fraction f NI ~71%. Instabilities driven by super-Alfv´enic ions will be an important issue for all burning plasmas, including ITER. Fast ions from NBI on NSTX are super-Alfv´enic. Linear TAE thresholds and appreciable fast-ion loss during multi-mode bursts are measured and these results are compared to theory. The impact of n > 1 error fields on stability is a important result for ITER. RWM/RFA feedback combined with n=3 error field control was used on NSTX to maintain plasma rotation with β above the no-wall limit. Other highlights are: results of lithium coating experiments, momentum confinement studies, scrape-off layer width scaling, demonstration of divertor heat load mitigation in strongly shaped plasmas, and coupling of CHI plasmas to OH ramp-up. These results advance the ST towards next step fusion energy devices such as NHTX and ST-CTF

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Solenoid-free plasma startup in NSTX using transient CHI

Experiments in NSTX have now demonstrated the coupling of toroidal plasmas produced by the technique of coaxial helicity injection (CHI) to inductive sustainment and ramp-up of the toroidal plasma current. In these discharges, the central Ohmic transformer was used to apply an inductive loop voltage to discharges with a toroidal current of about 100 kA created by CHI. The coupled discharges have ramped up to > 700 kA and transitioned into an H-mode demonstrating compatibility of this startup method with conventional operation. The electron temperature in the coupled discharges reached over 800 eV and the resulting plasma had low inductance, which is preferred for long-pulse high-performance discharges. These results from NSTX in combination with the previously obtained record 160 kA non-inductively generated startup currents in an ST or tokamak in NSTX demonstrate that CHI is a viable solenoid-free plasma startup method for future STs and tokamaks.

Raman, R↗

Divertor heat flux mitigation in high-performance H-mode discharges in the National Spherical Torus Experiment

Experiments conducted in high-performance 1.0 and 1.2 MA 6 MW NBI-heated H-mode discharges with a high magnetic flux expansion radiative divertor in NSTX demonstrate that significant divertor peak heat flux reduction and access to detachment may be facilitated naturally in a highly shaped spherical torus (ST) configuration. Improved plasma performance with high beta(t) = 15-25%, a high bootstrap current fraction f(BS) = 45-50%, longer plasma pulses and an H-mode regime with smaller ELMs has been achieved in the strongly shaped lower single null configuration with elongation kappa = 2.2-2.4 and triangularity delta = 0.7-0.8. Divertor peak heat fluxes were reduced from 6-12 to 0.5-2 MW m(-2) in ELMy H-mode discharges using the inherently high magnetic flux expansion f(m) = 15-25 and the partial detachment of the outer strike point at several D-2 injection rates. A good core confinement and pedestal characteristics were maintained, while the core carbon concentration and the associated Z(eff) were reduced. The partially detached divertor regime was characterized by an increase in divertor radiated power, a reduction in ion flux to the plate and a large neutral compression ratio. Spectroscopic measurements indicated the formation of a high-density, low-temperature region adjacent to the outer strike point, where substantial increases in the volume recombination rate and C II, CIII emission rates were measured.

Soukhanovskii, V. A.↗