Novel Method for Overmolding of NdFeB Bonded Magnets Into a 3-D Printed Rotor
Not Available
Kemp, James W.↗
Engineering topics
Mungale, Kaustubh
Publications and source records attributed to Mungale, Kaustubh.
Packing bimodal magnetic particles to fabricate highly dense anisotropic rare earth bonded permanent magnets
Bimodal particles of NdFeB and SmFeB yielded high-density bonded magnets. The energy product of 20 MGOe with 81 vol% magnet loading was demonstrated.
36 MATERIALS SCIENCE↗
Challenges in Postprocessing of Hybrid Manufacturing of Magnet Polymer Composites to Enhance the Energy Product of NdFeB Bonded Magnets
Bonded permanent magnets need to process magnetic filler particles and binder together which is a form of hybrid or composite manufacturing that needs to simultaneously process multimaterials. Polymer bonding of the permanent magnets decreases the energy product of the bonded magnets which varies with square of loading fraction of magnetic materials. However, due to high viscosity of bonding polymer prohibits loading higher than 80 volume % of magnetic materials in most efficient loading process such as compression molding. To further increase the loading of magnetic fraction in the bonded permanent magnets, it is expected to be beneficial to introduce a fraction of nonreacting thermally sacrificial polymer along with permanent bonding polymer in the least permissible of about 20 volume % of the polymer. This process of first adding the sacrificial polymer for higher processability for composites and later removing it via post processing such as heat treatment provides a simple example of inclusion of both the additive and the subtractive stages of hybrid manufacturing. These hybrid composite magnets can be heat treated to remove the sacrificial polymer to further increase the density and energy product which might require to implement hot isostatic pressing for compaction. Although the identification of such ideal polymer requires an extensive polymer chemistry research, we have compression molded several permanent bonding polymers such as nylon, polycarbonate (PC) and polyphenyl sulfide (PPS) and potential sacrificial polymer such as polyoxymethylene (POM), polystyrene (PS), and Acrylonitrile Butadiene Styrene (ABS) and heat treated to remove the sacrificial polymers. It is discovered that oxygen free low temperature pyrolizable polymers could be the potential candidates for increasing the magnet particles loading for achieving high energy products.
36 MATERIALS SCIENCE↗
Compression molding of anisotropic NdFeB bonded magnets in a polycarbonate matrix
Anisotropic bonded Nd 2 Fe 14 B (NdFeB) magnets in a polycarbonate (PC) binder matrix are fabricated using a compression molding process. The weight fractions (w.f.) of NdFeB in PC on the batch mixer are 20, 50, 75, 85 and 95% compared to the twin screw extruder with 20, 50 and 75% respectively. The density of the 95% batch mixed magnets fabricated was 5.34 g/cm 3 and the magnetic properties are, intrinsic coercivity H ci = 942.99 kA/m, remanence B r = 0.86 T, and energy product (BH) max = 120.96 kJ/m 3 . Furthermore, the measured tensile properties are in the range of 27-59 MPa, comparable to that of polyamide (PA), polyphenylene sulfide (PPS) bonded magnets and demonstrating potential for bonded magnet applications. Scanning electron microscopy showed that the onset of failure occurs in the magnetic particle- matrix interface. This study demonstrates that compression additive molding technique can be used to fabricate high performance NdFeB polycarbonate composite magnets with improved mechanical properties.
36 MATERIALS SCIENCE↗
HYBRID MANUFACTURING TECHNIQUE USING LARGE-SCALE ADDITIVE MANUFACTURING AND COMPRESSION MOLDING FOR HIGH PERFORMANCE COMPOSITES
Additive Manufacturing (AM) or 3-D printing has moved from small-scale prototypes to large-scale functional structures. With the introduction of large-scale 3D printers into the market a new industry has been born. For the first time, we are presenting the idea of preparing large-scale 3-D printed β-stage preforms to be used in traditional compression molding (CM) manufacturing technique to prepare final functional structures. Short carbon fiber (CF) reinforced material acrylonitrile butadiene Styrene i.e. ABS with 20% CF is used in present work. It is shown that highly aligned 3D printed short carbon fiber composite maintains its orientation after compression molding. A sandwich panel is prepared to show the capability to prepare complicated parts by integrating AM and CM. Interphase of the prepared dissimilar material is also studied using SEM. Samples prepared using AM-CM integration showed 11% and 79 % improvement in tensile strength and tensile modulus respectively compared to the traditional extrusion compression molding (ECM) process.
Kumar, Vipin↗