Search NASA⌕ Search

Engineering topics

Munshi, Amit

Publications and source records attributed to Munshi, Amit.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

CdTe-based thin film photovoltaics: Recent advances, current challenges and future prospects

Cadmium telluride (CdTe)-based cells have emerged as the leading commercialized thin film photovoltaic technology and has intrinsically better temperature coefficients, energy yield, and degradation rates than Si technologies. More than 30 GW peak (GWp) of CdTe-based modules are installed worldwide, multiple companies are in production, modules are shipping at up to 18.6% efficiency, and lab cell efficiency is above 22%. We review developments in the science and technology that have occurred over approximately the past decade. These achievements were enabled by manufacturing innovations and scaling module production, as well as maximizing photocurrent through window layer optimization and alloyed CdSe x Te 1-x (CST) absorbers. Improved chlorine passivation processes, film microstructure, and serendipitous Se defect passivation significantly increased minority carrier lifetime. Efficiencies >22% have been realized for both Cu and As doped CST-based cells. The path to further efficiency gains hinges primarily on increasing open circuit voltage (V oc ) and fill factor (FF) through innovations in materials, fabrication methods, and device stacks. Replacing the longstanding Cu doping with As doping is resulting in better module stability and is being translated to large-scale production. To realize 25% efficiency and >1 V V oc , research and development is needed to increase the minority carrier lifetime beyond 100 ns, reduce grain boundary and interface recombination, and tailor band diagrams at the front and back interfaces. Many of these goals have been realized separately however combining them together using scalable manufacturing approaches has been elusive to date. We review these achievements and outstanding opportunities for this remarkable photovoltaic technology.

14 SOLAR ENERGY↗
DOE OSTI2022

Electro-Optical Characterization of Arsenic-Doped CdSeTe and CdTe Solar Cell Absorbers Doped in-situ During Close Space Sublimation

Most contemporary device models predict that an acceptor concentration of at least 10^16 cm^-3 is required to reach an open circuit voltage of 1 V in polycrystalline CdTe-based solar cells. While copper has traditionally been used as the de facto p-type dopant in polycrystalline cadmium telluride (CdTe) and cadmium selenide telluride (CdSeTe), reaching high acceptor concentrations has proved to be challenging in such devices due to significant dopant compensation. The acceptor concentration in copper-doped CdTe and CdSeTe typically ranges from 10^13 to 10^15 cm^-3 and routinely exhibit low external radiative efficiencies below 0.01%, limiting their implied voltage (i.e., quasi-Fermi level splitting) to approximately 900 mV. As an alternative to copper, this work explores the use of arsenic as a p-type dopant for CdTe and CdSeTe. Using a novel technique in which a thin layer of arsenic-containing material is deposited and used as a reservoir for arsenic to diffuse into a front layer of previously undoped material, this contribution demonstrates that high external radiative efficiencies are achievable, a direct result of combined high acceptor concentrations and long minority-carrier lifetimes in the absorber. This leads to improved implied voltages, and indicates that As-doping represents a promising pathway towards improving the external voltage of CdSeTe/CdTe solar cells.

cadmium telluride↗
DOE OSTI2021

Understanding the Role of CdTe in Polycrystalline CdSe x Te 1– x /CdTe-Graded Bilayer Photovoltaic Devices

Grading of bandgap by alloying CdTe with selenium to form a CdSe x Te 1–x /CdTe-graded bilayer device has led to a device efficiency over 19%. A CdSe x Te 1–x absorber would increase the short-circuit current due to its lower bandgap but at the expense of open-circuit voltage. It has been demonstrated that adding a CdTe layer at the back of such a CdSe x Te 1–x film reduces the voltage deficit caused by the lower bandgap of absorber from selenium alloying while maintaining the higher short-circuit current. This leads to a photovoltaic device that draws advantage from both materials with an efficiency greater than either of them. In this report there is a detailed account using device data, ultraviolet photoelectron spectroscopy, electron microscopy, and first-principles density functional theory modeling is provided, which shows that CdTe acts as an electron reflector for CdSe x Te 1–x .

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Mitigation of J–V distortion in CdTe solar cells by Ga-doping of MgZnO emitter

Distortions in the current–voltage curves of CdTe-based thin-film solar cells with MgZnO emitter layers are not uncommon. Even when such distortions are very subtle with standard sunlight, they can be greatly accentuated by the removal of short-wavelength photons with optical filters, and the dark-curve turn-on voltage can be noticeably increased. The strong suggestion is that good J–V curves with full-spectrum light often rely on photogeneration of electrons from trap states in the MgZnO emitter. When the carrier concentration of the CdTe absorber is increased with external doping, there is a corresponding need for a larger MgZnO carrier concentration. Based on the assumption that the emitter carrier concentration needs to be comparable to that of the absorber, Ga-doping of the MgZnO was shown to very nearly eliminate the large filtered-light distortions and is arguably superior to MgZnO that relies on photogeneration. In addition, it was shown that photogeneration and recovery in MgZnO is relatively slow, so that without Ga-doping, the cell efficiency improves gradually for most of an hour in the light, and the turn-on voltage of the dark curve increases on a similar time scale when the light is removed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Transparent MgO for Back-Contact Passivation of CdTe-Based Solar Cells

The passivating effects of MgO have been studied by integrating into an existing superstrate CdTe thin film solar cell device architecture. When implemented as an emitter to replace the typical MZO, the device performance was below par, but improved PL and TRPL was detected with significant carrier lifetimes in comparison to the MZO devices. However, when integrated at the back, the PL signal was detected upon the illumination of excitation laser from the back. This has opened the possibility of probing the back of the CdTe thin film solar cells with transparent back contact with improved back passivation and a bifacial device structure. Further, the TRPL measurements suggests that the MgO shows passivating effects to a CdTe surface irrespective of method of deposition implemented.

bifacial↗
DOE OSTI2021

CdTe‐Based Solar Cells with Variations in Mg Concentration in the MgZnO Emitter

The optimal fraction of Mg incorporation in sputter-deposited Mg X Zn 1−X O (MZO) emitters for thin-film CdTe-based solar cells is evaluated by varying it over a range of x from 0 to 0.35. This range allows a variation in the conduction band offset from −0.1 eV (cliff like) to +0.32 eV (spike like). Here, a maximum efficiency of 18.5% for cells with the bilayer CdSeTe/CdTe absorber occurs at x = 0.15, which corresponds to a spike-like band offset near 0.2 eV, as confirmed by X-ray photoelectron spectroscopy. In addition, good cell performance is seen over a fairly broad range of x extending from 0.1 to 0.25. The MZO optical bandgap increases with the Mg fraction, consistent with an increasing conduction band offset. Temperature-dependent current−voltage measurements and time-resolved photoluminescence show improvement in the emitter/absorber interface with the incorporation of Mg. Capacitance−voltage measurements show that the depletion region extends further into the absorber with more Mg, and X-ray diffraction confirms a change from a hexagonal-dominant crystal structure toward zinc blende at x = 0.35.

14 SOLAR ENERGY↗
DOE OSTI2021

CdSexTe1-x/CdTe Devices with Reduced Interface Recombination Through Novel Back Contacts and Group-V Doping

Since excellent carrier lifetimes and front interface electronic quality are now achieved, rear interface recombination can limit V OC in CdSexTe1-x/CdTe solar cells. Several back-contact structures for devices were fabricated using combinations of tellurium, aluminum oxide, amorphous silicon, and indium tin oxide (ITO). Time-resolved photoluminescence was used to characterize such structures. We show increasingly improved interface passivation through the subsequent use of aluminum oxide, amorphous silicon, and ITO. Additionally, we show that arsenic-doped absorbers form a more passive interface with numerous back contact structures.

aluminum oxide↗
DOE OSTI2021

Microsecond Carrier Lifetimes in Polycrystalline CdSeTe Heterostructures and in CdSeTe Thin Film Solar Cells

We report significant advances in understanding and reducing nonradiative Shockley-Read-Hall recombination in polycrystalline CdSe x Te 1-x , leading to microsecond charge carrier lifetimes. In undoped Al 2 O 3 -passivated heterostructures we find external radiative efficiency 0.2%, quasi-Fermi level splitting 950 mV, mobility 100 cm 2 /(Vs), and diffusion length 14 µm. In solar cells measured lifetimes can exceed 1 µs. We interpret this data to indicate MgZnO/CdSeTe interface recombination velocity <; 100 cm/s. Based on our results, it appears CdTe PV technology has potentially overcome longstanding “recombination lifetime” limitation and in the near future will transition to improving other aspects of device design.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2021

Calculation of the Thermodynamic Voltage Limit of CdSeTe Solar Cells

The first step to understand the origin of losses in any photovoltaic solar cell is to determine the fundamental thermodynamic efficiency and voltage limits of such a device. In this contribution, we detail techniques to calculate the voltage limit in the case of cadmium selenium telluride (CdSeTe) solar cells, and how approaches based on bandgap alone—i.e., the Shockley-Queisser approach with step-function absorptance—can overestimate the thermodynamic open-circuit voltage limit Voc,ideal . This is particularly true for arsenic-doped samples, which tend to exhibit below-bandgap absorptance.

absorptance↗
DOE OSTI2020

Impact of Carrier Concentration and Carrier Lifetime on MgZnO/CdSeTe/CdTe Solar Cells

Here, the performance impact of multiple parameters related to the use of MgZnO (MZO) as the emitter for bilayer CdSeTe/CdTe solar cells has been investigated in detail through numerical simulations. Such a comprehensive study is particularly important, because while cell fabrication using MZO has been highly successful in some cases, it has been less so in others, and it has not been clear which combinations of parameter values are most effective. The parameters considered here include the recombination velocity at the emitter/absorber interface, bulk recombination lifetime, and the carrier concentrations of the emitter and absorber. The ranges chosen for the simulation parameters are those most likely to be found experimentally. The primary finding is that independent of the interfacial recombination velocity and bulk recombination lifetime, the MZO carrier density should be > 1017 cm-3 and in any case greater than that of the absorber to reduce interface recombination. At the same time, a shallow dopant the order of 50 meV or less should reduce SRH recombination in the bulk and enable VOC > 1V.

14 SOLAR ENERGY↗
DOE OSTI2020

Analysis of CdTe photovoltaic cells for ambient light energy harvesting

This paper investigates the suitability of CdTe photovoltaic cells to be used as power sources for wireless sensors located in buildings. We fabricate and test a CdTe photovoltaic cell with a transparent conducting oxide front contact that provides for high photocurrents and low series resistance at low light intensities and measures the photovoltaic response of this cell across five orders of magnitude of AM1.5G light intensity. Efficiencies of 10% and 17.1% are measured under ~1 W m -2 AM1.5G and LED irradiance respectively, the highest values for a CdTe device under ambient lighting measured to date. We use our results to assess the potential of CdTe for internet of things devices from an optoelectronic, as well as a techno-economic perspective, considering its established manufacturing know-how, potential for low-cost, proven long-term stability and issues around the use of cadmium.

14 SOLAR ENERGY↗
DOE OSTI2020

CdSexTe1-x /CdTe Devices With Reduced Interface Recombination Through Novel Back Contacts and Doping Strategies

In order to study rear interface recombination in CdSexTe1-x/CdTe solar cells, several back contact structures were fabricated using combinations of tellurium, alumina, amorphous silicon, and indium tin oxide. Film side Time-Resolved Photoluminescence measurements were taken to measure carrier lifetimes and interface recombination at the back interface. We show increasingly improved interface passivation through the subsequent use of alumina, amorphous silicon, and ITO. Additionally, we provide evidence that an arsenic-doped absorber forms a better interface with numerous back contact structures. Reductions in the back interface recombination velocity are shown to correlate with improvements in device external radiative efficiency.

13 HYDRO ENERGY↗
DOE OSTI2020

Arsenic Doping of Polycrystalline CdSeTe Devices for Microsecond Life-times with High Carrier Concentrations

We report seminal advances in fabrication and understanding of group V (As) doped thin-film polycrystalline CdTe-based solar cells. The devices are fabricated using a novel approach, by sublimating layers of CdSeTe and CdSeTe:As. This new method allowed us to achieve minority carrier lifetime of over 1 μs, carrier concentration of more than 5x1015 cc-1 and external radiative efficiency of over 2% in a device configuration. We find an increase in open-circuit voltage when comparing As-doped, Cu-doped and undoped devices. The choice of CdSeTe instead of a CdTe-only absorber has been explained using first-principle density functional theory model. A SCAPS device model is used to analyze the potential causes for lower open-circuit voltage.

14 SOLAR ENERGY↗
DOE OSTI2020

Light-Induced Metastabilities in Highly Efficient MZO/CdSeTe/CdTe Thin Film Solar Cells

Metastability effects have been investigated in high efficiency MZO/CdSeTe/CdTe solar cells. Two different preconditioning procedures have been studied to recover the performance of the devices. These preconditioning procedures include light soaking, annealing and cooling down the device under different atmospheric conditions. J-V curves before any preconditioning showed a `S` shaped behavior and disappears after 15 minutes of light soaking under 1000 Wm-2. Both Atmospheric and Vacuum preconditioning showed similar recovery of the device performance. However, this recovery only lasts for 3 days when the devices were kept under vacuum in the dark.

14 SOLAR ENERGY↗
DOE OSTI2020

Influence of Process Parameters and Absorber Thickness on Efficiency of Polycrystalline CdSeTe/CdTe Thin Film Solar Cells

Graded absorbers devices with with CdSe 0.4 Te 0.6 (molar basis) and CdTe were fabricated. CdCl 2 treatment time, post-deposition CdCl 2 anneal time and thicknesses of CdSeTe and CdTe layers were varied. Photoluminescence and electrical measurements were performed on the fabricated devices. Results revealed that the individual thicknesses of CdSeTe and CdTe is critical to overall efficiency of the devices. Device fabricated on substrate with 0.5 μm CdSeTe, 3 μm CdTe with rest of process parameters kept unchanged, produced an efficiency of 20.14%. We report highest device efficiency among academia and research institutions.

Shimpi, Tushar↗
DOE OSTI2020

Sputtered Aluminum Oxide and p+ Amorphous Silicon Back-Contact for Improved Hole Extraction in Polycrystalline CdSexTe1-x and CdTe Photovoltaics

A thin layer of Al 2 O 3 at the back of CdSe x T e1-x /CdTe devices is shown to passivate the back interface and drastically improve surface recombination lifetimes and photoluminescent response. Despite this, such devices do not show an improvement in open-circuit voltage (VOC.) Adding a p + amorphous silicon layer behind the Al 2 O 3 bends the conduction band upward, reducing the barrier to hole extraction and improving collection. Further optimization of the Al 2 O 3 , amorphous silicon (a-Si), and indium-doped tin oxide (ITO) layers, as well as their interaction with the CdCl 2 passivation process, are necessary to translate these electro-optical improvements into gains in voltage.

14 SOLAR ENERGY↗