Engineering topics

Murphy, Patrick C.

Publications and source records attributed to Murphy, Patrick C..

At least 19 records

NASA NTRS2019

Computational Study of a Generic T-tail Transport

This paper presents a computational study on the static and dynamic stability characteristics of a generic transport T-tail configuration under a NASA research program to improve stall models for civil transports. The NASA Tetrahedral Unstructured Software System (TetrUSS) was used to obtain both static and periodic dynamic solutions at low speed conditions for three Reynolds number conditions up to 60 deg angle of attack. The computational results are compared to experimental data. The dominant effects of Reynolds number for the static conditions were found to occur in the stall region. The pitch and roll damping coefficients compared well to experimental results up to up to 40 deg angle of attack whereas yaw damping coefficient agreed only up to 20 deg angle of attack.

McMillin, S. Naomi↗

NASA NTRS2019

Unsteady Model Estimation for Generic T-Tail Transport Aircraft Using Computational Data

Models including nonlinear and unsteady behaviors are developed for the longitudinal axis of the NASA Generic T-Tail Aircraft over a large range of angle of attack. These models are based on computational simulations of forced-oscillation tests in a wind tunnel. This work continues a recent study and an ongoing effort by NASA to improve aircraft simulations for pilot training in loss-of-control and stalled conditions. The objective of this work is to develop appropriate aerodynamic models that provide representative responses in simulation for a given class of aircraft. In the stall region, nonlinear unsteady responses are often present and may require an extended aerodynamic model compared to that used in the conventional flight envelope. In this study, two objectives are addressed. The first is to obtain representative models for the NASA Generic T-Tail aircraft over a wide range of angle of attack and the second is to continue development of a specialized CFD test technique that uses Schroeder sweeps to create information rich responses for unsteady aerodynamic model identification.

Murphy, Patrick C.↗

NASA NTRS2019

Investigation of Reduced-Order Modeling for Aircraft Stability and Control Prediction

High-fidelity computational fluid dynamics tools offer the potential to approximate increments for ground-to-flight scaling effects, as well as to augment the dynamic damping derivative data for motion-based flight simulators. Unfortunately, the computational expense is currently prohibitive for populating a complete simulator database. This work investigates an existing surrogate-based, indicial response reduced-order model methodology as a means to efficiently augment a flight simulator database with high-fidelity nonlinear aerodynamic damping derivatives. Creation of the reduced-order model is based on the superposition integrals of the step response with the derivative of its corresponding input signal. Step responses are calculated using a computational grid motion approach that separates the effects of angle of attack and sideslip angle from angular rates, and rates from angle of attack and sideslip. It is demonstrated that the transients produced during the start of a forced-oscillation motion are captured by the reduced-order model to the level of fidelity of a comparable computational solution. Aerodynamic coefficients computed within minutes by the reduced-order model for an aircraft undergoing an 18-second half Lazy-8 maneuver and a 25-second Immelmann turn maneuver are compared with those from full computational flight solutions that required days to complete. Finally, a cost-benefit assessment is included that demonstrates a compelling advantage for this approach. d for maneuvering, flexible vehicles.

Frink, Neal T.↗

NASA NTRS2019

Pilot Sensitivity to Simulator Flight Dynamics Model Formulation for Stall Training

A piloted simulation study was performed in the Cockpit Motion Facility at the National Aeronautics and Space Administration Langley Research Center. The research was motivated by the desire to reduce the commercial transport airplane fatal accident rate due to in-flight loss of control. The purpose of this study, which focused on a generic T-tail transport airplane, was to assess pilot sensitivity to flight dynamics model formulation used during a simulator stall recognition and recovery training/demonstration profile. To accomplish this, the flight dynamics model was designed with many configuration options. The model options were based on recently acquired static and dynamic stability and control data from sources that included wind tunnel, water tunnel, and computational fluid dynamics. The results, which are specific to a transport airplane stall recognition and recovery guided demonstration scenario, showed the two most important aerodynamic effects (other than stick pusher) to model were stall roll- off and the longitudinal static stability characteristic associated with the pitch break.

Cunningham, Kevin↗

NASA NTRS2018

Efficient Unsteady Model Estimation Using Computational and Experimental Data

Improving aircraft simulations for pilot training in loss-of-control and stalled conditions is one goal of NASA research in the System Wide Safety Program. One part of this effort is to develop appropriate generic aerodynamic models that provide representative responses in simulation for a given class of aircraft. In this part of the flight envelope nonlinear unsteady responses are often present and may require an extended aerodynamic model compared to that used in the conventional flight envelope. In this preliminary study, two objectives are addressed. First, to obtain a representative model for a NASA generic aircraft at an unsteady condition in the flight envelope and second, to evaluate the techniques involved. To meet these objectives, two different generic aircraft configurations are modeled using both experimental and analytical data. With these results, an initial assessment of the efficiency and quality of the tools and test techniques are evaluated to develop guidance for analytical and experimental approaches to unsteady modeling.

Murphy, Patrick C.↗

NASA NTRS2018

Preliminary Test Results for Stability and Control Characteristics of a Generic T-Tail Transport Airplane at High Angle of Attack

Tests of a generic T-tail transport airplane, in flaps-up configuration, were conducted using two wind tunnels, a water tunnel, and computational fluid dynamics. Static force and moment testing, forced oscillation testing and dye flow visualization test techniques were used. The purpose of the testing was to obtain stability and control characteristics for development of a research flight simulator aerodynamic database. The purpose of that database was for assessment of aerodynamic model fidelity requirements to train airline pilots to recognize and recover from full stall conditions. Preliminary results, at initial stall conditions, include: an unstable stall pitch break, and near-neutral roll damping. Preliminary results, at deep stall conditions, include: a potential static longitudinal trim condition at approximately 35 degrees angle of attack, large aerodynamic asymmetries, and localized unstable dynamic stability.

Cunningham, Kevin↗

NASA NTRS2017

Efficient Testing Combining Design of Experiment and Learn-to-Fly Strategies

Rapid modeling and efficient testing methods are important in a number of aerospace applications. In this study efficient testing strategies were evaluated in a wind tunnel test environment and combined to suggest a promising approach for both ground-based and flight-based experiments. Benefits of using Design of Experiment techniques, well established in scientific, military, and manufacturing applications are evaluated in combination with newly developing methods for global nonlinear modeling. The nonlinear modeling methods, referred to as Learn-to-Fly methods, utilize fuzzy logic and multivariate orthogonal function techniques that have been successfully demonstrated in flight test. The blended approach presented has a focus on experiment design and identifies a sequential testing process with clearly defined completion metrics that produce increased testing efficiency.

Murphy, Patrick C.↗

NASA NTRS2016

Status of Computational Aerodynamic Modeling Tools for Aircraft Loss-of-Control

A concerted effort has been underway over the past several years to evolve computational capabilities for modeling aircraft loss-of-control under the NASA Aviation Safety Program. A principal goal has been to develop reliable computational tools for predicting and analyzing the non-linear stability & control characteristics of aircraft near stall boundaries affecting safe flight, and for utilizing those predictions for creating augmented flight simulation models that improve pilot training. Pursuing such an ambitious task with limited resources required the forging of close collaborative relationships with a diverse body of computational aerodynamicists and flight simulation experts to leverage their respective research efforts into the creation of NASA tools to meet this goal. Considerable progress has been made and work remains to be done. This paper summarizes the status of the NASA effort to establish computational capabilities for modeling aircraft loss-of-control and offers recommendations for future work.

Frink, Neal T.↗

NASA NTRS2016

Nonlinear Unsteady Aerodynamic Modeling Using Wind Tunnel and Computational Data

Extensions to conventional aircraft aerodynamic models are required to adequately predict responses when nonlinear unsteady flight regimes are encountered, especially at high incidence angles and under maneuvering conditions. For a number of reasons, such as loss of control, both military and civilian aircraft may extend beyond normal and benign aerodynamic flight conditions. In addition, military applications may require controlled flight beyond the normal envelope, and civilian flight may require adequate recovery or prevention methods from these adverse conditions. These requirements have led to the development of more general aerodynamic modeling methods and provided impetus for researchers to improve both techniques and the degree of collaboration between analytical and experimental research efforts. In addition to more general mathematical model structures, dynamic test methods have been designed to provide sufficient information to allow model identification. This paper summarizes research to develop a modeling methodology appropriate for modeling aircraft aerodynamics that include nonlinear unsteady behaviors using both experimental and computational test methods. This work was done at Langley Research Center, primarily under the NASA Aviation Safety Program, to address aircraft loss of control, prevention, and recovery aerodynamics.

Murphy, Patrick C.↗

NASA NTRS2015

Experiment Design for Complex VTOL Aircraft with Distributed Propulsion and Tilt Wing

Selected experimental results from a wind tunnel study of a subscale VTOL concept with distributed propulsion and tilt lifting surfaces are presented. The vehicle complexity and automated test facility were ideal for use with a randomized designed experiment. Design of Experiments and Response Surface Methods were invoked to produce run efficient, statistically rigorous regression models with minimized prediction error. Static tests were conducted at the NASA Langley 12-Foot Low-Speed Tunnel to model all six aerodynamic coefficients over a large flight envelope. This work supports investigations at NASA Langley in developing advanced configurations, simulations, and advanced control systems.

Murphy, Patrick C.↗

NASA NTRS2014

Enabling Advanced Wind-Tunnel Research Methods Using the NASA Langley 12-Foot Low Speed Tunnel

Design of Experiment (DOE) testing methods were used to gather wind tunnel data characterizing the aerodynamic and propulsion forces and moments acting on a complex vehicle configuration with 10 motor-driven propellers, 9 control surfaces, a tilt wing, and a tilt tail. This paper describes the potential benefits and practical implications of using DOE methods for wind tunnel testing - with an emphasis on describing how it can affect model hardware, facility hardware, and software for control and data acquisition. With up to 23 independent variables (19 model and 2 tunnel) for some vehicle configurations, this recent test also provides an excellent example of using DOE methods to assess critical coupling effects in a reasonable timeframe for complex vehicle configurations. Results for an exploratory test using conventional angle of attack sweeps to assess aerodynamic hysteresis is summarized, and DOE results are presented for an exploratory test used to set the data sampling time for the overall test. DOE results are also shown for one production test characterizing normal force in the Cruise mode for the vehicle.

Busan, Ronald C.↗

NASA NTRS2014

NASA Langley Distributed Propulsion VTOL Tilt-Wing Aircraft Testing, Modeling, Simulation, Control, and Flight Test Development

Control of complex Vertical Take-Off and Landing (VTOL) aircraft traversing from hovering to wing born flight mode and back poses notoriously difficult modeling, simulation, control, and flight-testing challenges. This paper provides an overview of the techniques and advances required to develop the GL-10 tilt-wing, tilt-tail, long endurance, VTOL aircraft control system. The GL-10 prototype's unusual and complex configuration requires application of state-of-the-art techniques and some significant advances in wind tunnel infrastructure automation, efficient Design Of Experiments (DOE) tunnel test techniques, modeling, multi-body equations of motion, multi-body actuator models, simulation, control algorithm design, and flight test avionics, testing, and analysis. The following compendium surveys key disciplines required to develop an effective control system for this challenging vehicle in this on-going effort.

Rothhaar, Paul M.↗

NASA NTRS2014

Low-speed Aerodynamic Investigations of a Hybrid Wing Body Configuration

Two low-speed static wind tunnel tests and a water tunnel static and dynamic forced-motion test have been conducted on a hybrid wing-body (HWB) twinjet configuration. These tests, in addition to computational fluid dynamics (CFD) analysis, have provided a comprehensive dataset of the low-speed aerodynamic characteristics of this nonproprietary configuration. In addition to force and moment measurements, the tests included surface pressures, flow visualization, and off-body particle image velocimetry measurements. This paper will summarize the results of these tests and highlight the data that is available for code comparison or additional analysis.

Vicroy, Dan D.↗

NASA NTRS2014

Hybrid Wing Body Model Identification Using Forced-Oscillation Water Tunnel Data

Static and dynamic testing of the NASA 0.7 percent scale Hybrid Wing Body (HWB) configuration was conducted in the Rolling Hills Research Corporation water tunnel to investigate aerodynamic behavior over a large range of angle-of-attack and to develop models that can predict aircraft response in nonlinear unsteady flight regimes. This paper reports primarily on the longitudinal axis results. Flow visualization tests were also performed. These tests provide additional static data and new dynamic data that complement tests conducted at NASA Langley 14- by 22-Foot Subsonic Tunnel. HWB was developed to support the NASA Environmentally Responsible Aviation Project goals of lower noise, emissions, and fuel burn. This study also supports the NASA Aviation Safety Program efforts to model and control advanced transport configurations in loss-of-control conditions.

Murphy, Patrick C.↗

NASA NTRS2014

Roll Damping Derivatives from Generalized Lifting-Surface Theory and Wind Tunnel Forced-Oscillation Tests

Improving aerodynamic models for adverse loss-of-control conditions in flight is an area being researched under the NASA Aviation Safety Program. Aerodynamic models appropriate for loss of control conditions require a more general mathematical representation to predict nonlinear unsteady behaviors. As more general aerodynamic models are studied that include nonlinear higher order effects, the possibility of measurements that confound aerodynamic and structural responses are probable. In this study an initial step is taken to look at including structural flexibility in analysis of rigid-body forced-oscillation testing that accounts for dynamic rig, sting and balance flexibility. Because of the significant testing required and associated costs in a general study, it makes sense to capitalize on low cost analytical methods where possible, especially where structural flexibility can be accounted for by a low cost method. This paper provides an initial look at using linear lifting surface theory applied to rigid-body aircraft roll forced-oscillation tests.

Pototzky, Anthony S↗

NASA NTRS2012

Unsteady Aerodynamic Modeling in Roll for the NASA Generic Transport Model

Reducing the impact of loss-of-control conditions on commercial transport aircraft is a primary goal of the NASA Aviation Safety Program. One aspect in developing the supporting technologies is to improve the aerodynamic models that represent these adverse conditions. Aerodynamic models appropriate for loss of control conditions require a more general mathematical representation to predict nonlinear unsteady behaviors. In this paper, a more general mathematical model is proposed for the subscale NASA Generic Transport Model (GTM) that covers both low and high angles of attack. Particular attention is devoted to the stall region where full-scale transports have demonstrated a tendency for roll instability. The complete aerodynamic model was estimated from dynamic wind-tunnel data. Advanced computational methods are used to improve understanding and visualize the flow physics within the region where roll instability is a factor.

Murphy, Patrick C.↗

NASA NTRS2012

Aerodynamic Effects of Simulated Ice Accretion on a Generic Transport Model

An experimental research effort was begun to develop a database of airplane aerodynamic characteristics with simulated ice accretion over a large range of incidence and sideslip angles. Wind-tunnel testing was performed at the NASA Langley 12-ft Low-Speed Wind Tunnel using a 3.5 percent scale model of the NASA Langley Generic Transport Model. Aerodynamic data were acquired from a six-component force and moment balance in static-model sweeps from alpha = -5deg to 85deg and beta = -45 deg to 45 deg at a Reynolds number of 0.24 x10(exp 6) and Mach number of 0.06. The 3.5 percent scale GTM was tested in both the clean configuration and with full-span artificial ice shapes attached to the leading edges of the wing, horizontal and vertical tail. Aerodynamic results for the clean airplane configuration compared favorably with similar experiments carried out on a 5.5 percent scale GTM. The addition of the large, glaze-horn type ice shapes did result in an increase in airplane drag coefficient but had little effect on the lift and pitching moment. The lateral-directional characteristics showed mixed results with a small effect of the ice shapes observed in some cases. The flow visualization images revealed the presence and evolution of a spanwise-running vortex on the wing that was the dominant feature of the flowfield for both clean and iced configurations. The lack of ice-induced performance and flowfield effects observed in this effort was likely due to Reynolds number effects for the clean configuration. Estimates of full-scale baseline performance were included in this analysis to illustrate the potential icing effects.

Broeren, Andy P.↗

NASA NTRS2012

The Effect of Systematic Error in Forced Oscillation Testing

One of the fundamental problems in flight dynamics is the formulation of aerodynamic forces and moments acting on an aircraft in arbitrary motion. Classically, conventional stability derivatives are used for the representation of aerodynamic loads in the aircraft equations of motion. However, for modern aircraft with highly nonlinear and unsteady aerodynamic characteristics undergoing maneuvers at high angle of attack and/or angular rates the conventional stability derivative model is no longer valid. Attempts to formulate aerodynamic model equations with unsteady terms are based on several different wind tunnel techniques: for example, captive, wind tunnel single degree-of-freedom, and wind tunnel free-flying techniques. One of the most common techniques is forced oscillation testing. However, the forced oscillation testing method does not address the systematic and systematic correlation errors from the test apparatus that cause inconsistencies in the measured oscillatory stability derivatives. The primary objective of this study is to identify the possible sources and magnitude of systematic error in representative dynamic test apparatuses. Sensitivities of the longitudinal stability derivatives to systematic errors are computed, using a high fidelity simulation of a forced oscillation test rig, and assessed using both Design of Experiments and Monte Carlo methods.

Williams, Brianne Y.↗